alex/esp-idf
alex/esp-idf
1
0
Fork 0
mirror of https://github.com/espressif/esp-idf.git synced 2024-10-05 20:47:46 -04:00
Code Issues Actions 2 Packages Projects Releases Wiki Activity
master
esp-idf/examples/peripherals/mcpwm/mcpwm_servo_control
History
laokaiyao cb22b8aaf7 ci(esp32c5): enable c5 target test
2024-07-02 16:45:49 +08:00
..
main refactor(examples): reformat peripheral examples with astyle_py 2023-09-28 10:08:04 +08:00
CMakeLists.txt tools: Increase the minimal supported CMake version to 3.16 2022-06-01 06:35:02 +00:00
pytest_servo_mg996r.py ci(esp32c5): enable c5 target test 2024-07-02 16:45:49 +08:00
README.md remove(c5beta3): remove c5 beta3 doxy files 2024-06-17 12:02:15 +08:00

README.md

Supported Targets ESP32 ESP32-C5 ESP32-C6 ESP32-H2 ESP32-P4 ESP32-S3

MCPWM RC Servo Control Example

(See the README.md file in the upper level 'examples' directory for more information about examples.)

This example illustrates how to drive a typical RC Servo by sending a PWM signal using the MCPWM driver. The PWM pulse has a frequency of 50Hz (period of 20ms), and the active-high time (which controls the rotation) ranges from 0.5s to 2.5ms with 1.5ms always being center of range.

How to Use Example

Hardware Required

  • A development board with any Espressif SoC which features MCPWM peripheral (e.g., ESP32-DevKitC, ESP-WROVER-KIT, etc.)
  • A USB cable for Power supply and programming
  • A RC servo motor, e.g. SG90

Connection :

      ESP Board              Servo Motor      5V
+-------------------+     +---------------+    ^
|  SERVO_PULSE_GPIO +-----+PWM        VCC +----+
|                   |     |               |
|               GND +-----+GND            |
+-------------------+     +---------------+

Note that, some kind of servo might need a higher current supply than the development board usually can provide. It's recommended to power the servo separately.

Build and Flash

Run idf.py -p PORT flash monitor to build, flash and monitor the project.

(To exit the serial monitor, type Ctrl-].)

See the Getting Started Guide for full steps to configure and use ESP-IDF to build projects.

Example Output

Run the example, you will see the following output log:

...
I (0) cpu_start: Starting scheduler on APP CPU.
I (305) example: Create timer and operator
I (305) example: Connect timer and operator
I (305) example: Create comparator and generator from the operator
I (315) gpio: GPIO[44]| InputEn: 0| OutputEn: 1| OpenDrain: 0| Pullup: 1| Pulldown: 0| Intr:0
I (325) example: Set generator action on timer and compare event
I (335) example: Enable and start timer
I (335) example: Angle of rotation: 0
I (1345) example: Angle of rotation: 2
I (2345) example: Angle of rotation: 4
I (3345) example: Angle of rotation: 6
I (4345) example: Angle of rotation: 8
I (5345) example: Angle of rotation: 10
I (6345) example: Angle of rotation: 12
I (7345) example: Angle of rotation: 14
I (8345) example: Angle of rotation: 16
I (9345) example: Angle of rotation: 18
...

The servo will rotate from -60 degree to 60 degree, and then turn back again.

Troubleshooting

For any technical queries, please open an [issue] (https://github.com/espressif/esp-idf/issues) on GitHub. We will get back to you soon.