/* * SPDX-FileCopyrightText: 2015-2023 Espressif Systems (Shanghai) CO LTD * * SPDX-License-Identifier: Apache-2.0 */ #pragma once #include "esp_err.h" #include "esp_intr_alloc.h" #include "hal/ledc_types.h" #include "driver/gpio.h" #ifdef __cplusplus extern "C" { #endif #if SOC_LEDC_SUPPORT_APB_CLOCK /** * @brief Frequency of one of the LEDC peripheral clock sources, APB_CLK * @note This macro should have no use in your application, we keep it here only for backward compatible */ #define LEDC_APB_CLK_HZ _Pragma ("GCC warning \"'LEDC_APB_CLK_HZ' macro is deprecated\"") (APB_CLK_FREQ) #endif #if SOC_LEDC_SUPPORT_REF_TICK /** * @brief Frequency of one of the LEDC peripheral clock sources, REF_TICK * @note This macro should have no use in your application, we keep it here only for backward compatible */ #define LEDC_REF_CLK_HZ _Pragma ("GCC warning \"'LEDC_REF_CLK_HZ' macro is deprecated\"") (REF_CLK_FREQ) #endif #define LEDC_ERR_DUTY (0xFFFFFFFF) #define LEDC_ERR_VAL (-1) /** * @brief Configuration parameters of LEDC channel for ledc_channel_config function */ typedef struct { int gpio_num; /*!< the LEDC output gpio_num, if you want to use gpio16, gpio_num = 16 */ ledc_mode_t speed_mode; /*!< LEDC speed speed_mode, high-speed mode (only exists on esp32) or low-speed mode */ ledc_channel_t channel; /*!< LEDC channel (0 - LEDC_CHANNEL_MAX-1) */ ledc_intr_type_t intr_type; /*!< configure interrupt, Fade interrupt enable or Fade interrupt disable */ ledc_timer_t timer_sel; /*!< Select the timer source of channel (0 - LEDC_TIMER_MAX-1) */ uint32_t duty; /*!< LEDC channel duty, the range of duty setting is [0, (2**duty_resolution)] */ int hpoint; /*!< LEDC channel hpoint value, the range is [0, (2**duty_resolution)-1] */ struct { unsigned int output_invert: 1;/*!< Enable (1) or disable (0) gpio output invert */ } flags; /*!< LEDC flags */ } ledc_channel_config_t; /** * @brief Configuration parameters of LEDC timer for ledc_timer_config function */ typedef struct { ledc_mode_t speed_mode; /*!< LEDC speed speed_mode, high-speed mode (only exists on esp32) or low-speed mode */ ledc_timer_bit_t duty_resolution; /*!< LEDC channel duty resolution */ ledc_timer_t timer_num; /*!< The timer source of channel (0 - LEDC_TIMER_MAX-1) */ uint32_t freq_hz; /*!< LEDC timer frequency (Hz) */ ledc_clk_cfg_t clk_cfg; /*!< Configure LEDC source clock from ledc_clk_cfg_t. Note that LEDC_USE_RC_FAST_CLK and LEDC_USE_XTAL_CLK are non-timer-specific clock sources. You can not have one LEDC timer uses RC_FAST_CLK as the clock source and have another LEDC timer uses XTAL_CLK as its clock source. All chips except esp32 and esp32s2 do not have timer-specific clock sources, which means clock source for all timers must be the same one. */ bool deconfigure; /*!< Set this field to de-configure a LEDC timer which has been configured before Note that it will not check whether the timer wants to be de-configured is binded to any channel. Also, the timer has to be paused first before it can be de-configured. When this field is set, duty_resolution, freq_hz, clk_cfg fields are ignored. */ } ledc_timer_config_t; typedef intr_handle_t ledc_isr_handle_t; /** * @brief LEDC callback event type */ typedef enum { LEDC_FADE_END_EVT /**< LEDC fade end event */ } ledc_cb_event_t; /** * @brief LEDC callback parameter */ typedef struct { ledc_cb_event_t event; /**< Event name */ uint32_t speed_mode; /**< Speed mode of the LEDC channel group */ uint32_t channel; /**< LEDC channel (0 - LEDC_CHANNEL_MAX-1) */ uint32_t duty; /**< LEDC current duty of the channel, the range of duty is [0, (2**duty_resolution)] */ } ledc_cb_param_t; /** * @brief Type of LEDC event callback * @param param LEDC callback parameter * @param user_arg User registered data * @return Whether a high priority task has been waken up by this function */ typedef bool (*ledc_cb_t)(const ledc_cb_param_t *param, void *user_arg); /** * @brief Group of supported LEDC callbacks * @note The callbacks are all running under ISR environment */ typedef struct { ledc_cb_t fade_cb; /**< LEDC fade_end callback function */ } ledc_cbs_t; /** * @brief LEDC channel configuration * Configure LEDC channel with the given channel/output gpio_num/interrupt/source timer/frequency(Hz)/LEDC duty * * @param ledc_conf Pointer of LEDC channel configure struct * * @return * - ESP_OK Success * - ESP_ERR_INVALID_ARG Parameter error */ esp_err_t ledc_channel_config(const ledc_channel_config_t *ledc_conf); /** * @brief Helper function to find the maximum possible duty resolution in bits for ledc_timer_config() * * @param src_clk_freq LEDC timer source clock frequency (Hz) (See doxygen comments of `ledc_clk_cfg_t` or get from `esp_clk_tree_src_get_freq_hz`) * @param timer_freq Desired LEDC timer frequency (Hz) * * @return * - 0 The timer frequency cannot be achieved * - Others The largest duty resolution value to be set */ uint32_t ledc_find_suitable_duty_resolution(uint32_t src_clk_freq, uint32_t timer_freq); /** * @brief LEDC timer configuration * Configure LEDC timer with the given source timer/frequency(Hz)/duty_resolution * * @param timer_conf Pointer of LEDC timer configure struct * * @return * - ESP_OK Success * - ESP_ERR_INVALID_ARG Parameter error * - ESP_FAIL Can not find a proper pre-divider number base on the given frequency and the current duty_resolution. * - ESP_ERR_INVALID_STATE Timer cannot be de-configured because timer is not configured or is not paused */ esp_err_t ledc_timer_config(const ledc_timer_config_t *timer_conf); /** * @brief LEDC update channel parameters * * @note Call this function to activate the LEDC updated parameters. * After ledc_set_duty, we need to call this function to update the settings. * And the new LEDC parameters don't take effect until the next PWM cycle. * @note ledc_set_duty, ledc_set_duty_with_hpoint and ledc_update_duty are not thread-safe, do not call these functions to * control one LEDC channel in different tasks at the same time. * A thread-safe version of API is ledc_set_duty_and_update * @note If `CONFIG_LEDC_CTRL_FUNC_IN_IRAM` is enabled, this function will be placed in the IRAM by linker, * makes it possible to execute even when the Cache is disabled. * @note This function is allowed to run within ISR context. * * @param speed_mode Select the LEDC channel group with specified speed mode. Note that not all targets support high speed mode. * @param channel LEDC channel (0 - LEDC_CHANNEL_MAX-1), select from ledc_channel_t * * @return * - ESP_OK Success * - ESP_ERR_INVALID_ARG Parameter error */ esp_err_t ledc_update_duty(ledc_mode_t speed_mode, ledc_channel_t channel); /** * @brief Set LEDC output gpio. * * @note This function only routes the LEDC signal to GPIO through matrix, other LEDC resources initialization are not involved. * Please use `ledc_channel_config()` instead to fully configure a LEDC channel. * * @param gpio_num The LEDC output gpio * @param speed_mode Select the LEDC channel group with specified speed mode. Note that not all targets support high speed mode. * @param ledc_channel LEDC channel (0 - LEDC_CHANNEL_MAX-1), select from ledc_channel_t * * @return * - ESP_OK Success * - ESP_ERR_INVALID_ARG Parameter error */ esp_err_t ledc_set_pin(int gpio_num, ledc_mode_t speed_mode, ledc_channel_t ledc_channel); /** * @brief LEDC stop. * Disable LEDC output, and set idle level * * @note If `CONFIG_LEDC_CTRL_FUNC_IN_IRAM` is enabled, this function will be placed in the IRAM by linker, * makes it possible to execute even when the Cache is disabled. * @note This function is allowed to run within ISR context. * * @param speed_mode Select the LEDC channel group with specified speed mode. Note that not all targets support high speed mode. * @param channel LEDC channel (0 - LEDC_CHANNEL_MAX-1), select from ledc_channel_t * @param idle_level Set output idle level after LEDC stops. * * @return * - ESP_OK Success * - ESP_ERR_INVALID_ARG Parameter error */ esp_err_t ledc_stop(ledc_mode_t speed_mode, ledc_channel_t channel, uint32_t idle_level); /** * @brief LEDC set channel frequency (Hz) * * @param speed_mode Select the LEDC channel group with specified speed mode. Note that not all targets support high speed mode. * @param timer_num LEDC timer index (0-3), select from ledc_timer_t * @param freq_hz Set the LEDC frequency * * @return * - ESP_OK Success * - ESP_ERR_INVALID_ARG Parameter error * - ESP_FAIL Can not find a proper pre-divider number base on the given frequency and the current duty_resolution. */ esp_err_t ledc_set_freq(ledc_mode_t speed_mode, ledc_timer_t timer_num, uint32_t freq_hz); /** * @brief LEDC get channel frequency (Hz) * * @param speed_mode Select the LEDC channel group with specified speed mode. Note that not all targets support high speed mode. * @param timer_num LEDC timer index (0-3), select from ledc_timer_t * * @return * - 0 error * - Others Current LEDC frequency */ uint32_t ledc_get_freq(ledc_mode_t speed_mode, ledc_timer_t timer_num); /** * @brief LEDC set duty and hpoint value * Only after calling ledc_update_duty will the duty update. * * @note ledc_set_duty, ledc_set_duty_with_hpoint and ledc_update_duty are not thread-safe, do not call these functions to * control one LEDC channel in different tasks at the same time. * A thread-safe version of API is ledc_set_duty_and_update * @note For ESP32, hardware does not support any duty change while a fade operation is running in progress on that channel. * Other duty operations will have to wait until the fade operation has finished. * * @param speed_mode Select the LEDC channel group with specified speed mode. Note that not all targets support high speed mode. * @param channel LEDC channel (0 - LEDC_CHANNEL_MAX-1), select from ledc_channel_t * @param duty Set the LEDC duty, the range of duty setting is [0, (2**duty_resolution)] * @param hpoint Set the LEDC hpoint value, the range is [0, (2**duty_resolution)-1] * * @return * - ESP_OK Success * - ESP_ERR_INVALID_ARG Parameter error */ esp_err_t ledc_set_duty_with_hpoint(ledc_mode_t speed_mode, ledc_channel_t channel, uint32_t duty, uint32_t hpoint); /** * @brief LEDC get hpoint value, the counter value when the output is set high level. * * @param speed_mode Select the LEDC channel group with specified speed mode. Note that not all targets support high speed mode. * @param channel LEDC channel (0 - LEDC_CHANNEL_MAX-1), select from ledc_channel_t * * @return * - LEDC_ERR_VAL if parameter error * - Others Current hpoint value of LEDC channel */ int ledc_get_hpoint(ledc_mode_t speed_mode, ledc_channel_t channel); /** * @brief LEDC set duty * This function do not change the hpoint value of this channel. if needed, please call ledc_set_duty_with_hpoint. * only after calling ledc_update_duty will the duty update. * * @note ledc_set_duty, ledc_set_duty_with_hpoint and ledc_update_duty are not thread-safe, do not call these functions to * control one LEDC channel in different tasks at the same time. * A thread-safe version of API is ledc_set_duty_and_update. * @note For ESP32, hardware does not support any duty change while a fade operation is running in progress on that channel. * Other duty operations will have to wait until the fade operation has finished. * * @param speed_mode Select the LEDC channel group with specified speed mode. Note that not all targets support high speed mode. * @param channel LEDC channel (0 - LEDC_CHANNEL_MAX-1), select from ledc_channel_t * @param duty Set the LEDC duty, the range of duty setting is [0, (2**duty_resolution)] * * @return * - ESP_OK Success * - ESP_ERR_INVALID_ARG Parameter error */ esp_err_t ledc_set_duty(ledc_mode_t speed_mode, ledc_channel_t channel, uint32_t duty); /** * @brief LEDC get duty * This function returns the duty at the present PWM cycle. * You shouldn't expect the function to return the new duty in the same cycle of calling ledc_update_duty, * because duty update doesn't take effect until the next cycle. * * @param speed_mode Select the LEDC channel group with specified speed mode. Note that not all targets support high speed mode. * @param channel LEDC channel (0 - LEDC_CHANNEL_MAX-1), select from ledc_channel_t * * @return * - LEDC_ERR_DUTY if parameter error * - Others Current LEDC duty */ uint32_t ledc_get_duty(ledc_mode_t speed_mode, ledc_channel_t channel); /** * @brief LEDC set gradient * Set LEDC gradient, After the function calls the ledc_update_duty function, the function can take effect. * * @note For ESP32, hardware does not support any duty change while a fade operation is running in progress on that channel. * Other duty operations will have to wait until the fade operation has finished. * * @param speed_mode Select the LEDC channel group with specified speed mode. Note that not all targets support high speed mode. * @param channel LEDC channel (0 - LEDC_CHANNEL_MAX-1), select from ledc_channel_t * @param duty Set the start of the gradient duty, the range of duty setting is [0, (2**duty_resolution)] * @param fade_direction Set the direction of the gradient * @param step_num Set the number of the gradient * @param duty_cycle_num Set how many LEDC tick each time the gradient lasts * @param duty_scale Set gradient change amplitude * * @return * - ESP_OK Success * - ESP_ERR_INVALID_ARG Parameter error */ esp_err_t ledc_set_fade(ledc_mode_t speed_mode, ledc_channel_t channel, uint32_t duty, ledc_duty_direction_t fade_direction, uint32_t step_num, uint32_t duty_cycle_num, uint32_t duty_scale); /** * @brief Register LEDC interrupt handler, the handler is an ISR. * The handler will be attached to the same CPU core that this function is running on. * * @param fn Interrupt handler function. * @param arg User-supplied argument passed to the handler function. * @param intr_alloc_flags Flags used to allocate the interrupt. One or multiple (ORred) * ESP_INTR_FLAG_* values. See esp_intr_alloc.h for more info. * @param handle Pointer to return handle. If non-NULL, a handle for the interrupt will * be returned here. * * @return * - ESP_OK Success * - ESP_ERR_INVALID_ARG Parameter error * - ESP_ERR_NOT_FOUND Failed to find available interrupt source */ esp_err_t ledc_isr_register(void (*fn)(void *), void *arg, int intr_alloc_flags, ledc_isr_handle_t *handle); /** * @brief Configure LEDC settings * * @param speed_mode Select the LEDC channel group with specified speed mode. Note that not all targets support high speed mode. * @param timer_sel Timer index (0-3), there are 4 timers in LEDC module * @param clock_divider Timer clock divide value, the timer clock is divided from the selected clock source * @param duty_resolution Resolution of duty setting in number of bits. The range is [1, SOC_LEDC_TIMER_BIT_WIDTH] * @param clk_src Select LEDC source clock. * * @return * - (-1) Parameter error * - Other Current LEDC duty */ esp_err_t ledc_timer_set(ledc_mode_t speed_mode, ledc_timer_t timer_sel, uint32_t clock_divider, uint32_t duty_resolution, ledc_clk_src_t clk_src); /** * @brief Reset LEDC timer * * @param speed_mode Select the LEDC channel group with specified speed mode. Note that not all targets support high speed mode. * @param timer_sel LEDC timer index (0-3), select from ledc_timer_t * * @return * - ESP_ERR_INVALID_ARG Parameter error * - ESP_OK Success */ esp_err_t ledc_timer_rst(ledc_mode_t speed_mode, ledc_timer_t timer_sel); /** * @brief Pause LEDC timer counter * * @param speed_mode Select the LEDC channel group with specified speed mode. Note that not all targets support high speed mode. * @param timer_sel LEDC timer index (0-3), select from ledc_timer_t * * @return * - ESP_ERR_INVALID_ARG Parameter error * - ESP_OK Success */ esp_err_t ledc_timer_pause(ledc_mode_t speed_mode, ledc_timer_t timer_sel); /** * @brief Resume LEDC timer * * @param speed_mode Select the LEDC channel group with specified speed mode. Note that not all targets support high speed mode. * @param timer_sel LEDC timer index (0-3), select from ledc_timer_t * * @return * - ESP_ERR_INVALID_ARG Parameter error * - ESP_OK Success */ esp_err_t ledc_timer_resume(ledc_mode_t speed_mode, ledc_timer_t timer_sel); /** * @brief Bind LEDC channel with the selected timer * * @param speed_mode Select the LEDC channel group with specified speed mode. Note that not all targets support high speed mode. * @param channel LEDC channel index (0 - LEDC_CHANNEL_MAX-1), select from ledc_channel_t * @param timer_sel LEDC timer index (0-3), select from ledc_timer_t * * @return * - ESP_ERR_INVALID_ARG Parameter error * - ESP_OK Success */ esp_err_t ledc_bind_channel_timer(ledc_mode_t speed_mode, ledc_channel_t channel, ledc_timer_t timer_sel); /** * @brief Set LEDC fade function. * * @note Call ledc_fade_func_install() once before calling this function. * Call ledc_fade_start() after this to start fading. * @note ledc_set_fade_with_step, ledc_set_fade_with_time and ledc_fade_start are not thread-safe, do not call these functions to * control one LEDC channel in different tasks at the same time. * A thread-safe version of API is ledc_set_fade_step_and_start * @note For ESP32, hardware does not support any duty change while a fade operation is running in progress on that channel. * Other duty operations will have to wait until the fade operation has finished. * * @param speed_mode Select the LEDC channel group with specified speed mode. Note that not all targets support high speed mode. * @param channel LEDC channel index (0 - LEDC_CHANNEL_MAX-1), select from ledc_channel_t * @param target_duty Target duty of fading [0, (2**duty_resolution)] * @param scale Controls the increase or decrease step scale. * @param cycle_num increase or decrease the duty every cycle_num cycles * * @return * - ESP_OK Success * - ESP_ERR_INVALID_ARG Parameter error * - ESP_ERR_INVALID_STATE Channel not initialized * - ESP_FAIL Fade function init error */ esp_err_t ledc_set_fade_with_step(ledc_mode_t speed_mode, ledc_channel_t channel, uint32_t target_duty, uint32_t scale, uint32_t cycle_num); /** * @brief Set LEDC fade function, with a limited time. * * @note Call ledc_fade_func_install() once before calling this function. * Call ledc_fade_start() after this to start fading. * @note ledc_set_fade_with_step, ledc_set_fade_with_time and ledc_fade_start are not thread-safe, do not call these functions to * control one LEDC channel in different tasks at the same time. * A thread-safe version of API is ledc_set_fade_step_and_start * @note For ESP32, hardware does not support any duty change while a fade operation is running in progress on that channel. * Other duty operations will have to wait until the fade operation has finished. * * @param speed_mode Select the LEDC channel group with specified speed mode. Note that not all targets support high speed mode. * @param channel LEDC channel index (0 - LEDC_CHANNEL_MAX-1), select from ledc_channel_t * @param target_duty Target duty of fading [0, (2**duty_resolution)] * @param max_fade_time_ms The maximum time of the fading ( ms ). * * @return * - ESP_OK Success * - ESP_ERR_INVALID_ARG Parameter error * - ESP_ERR_INVALID_STATE Channel not initialized * - ESP_FAIL Fade function init error */ esp_err_t ledc_set_fade_with_time(ledc_mode_t speed_mode, ledc_channel_t channel, uint32_t target_duty, int max_fade_time_ms); /** * @brief Install LEDC fade function. This function will occupy interrupt of LEDC module. * * @param intr_alloc_flags Flags used to allocate the interrupt. One or multiple (ORred) * ESP_INTR_FLAG_* values. See esp_intr_alloc.h for more info. * * @return * - ESP_OK Success * - ESP_ERR_INVALID_ARG Intr flag error * - ESP_ERR_NOT_FOUND Failed to find available interrupt source * - ESP_ERR_INVALID_STATE Fade function already installed */ esp_err_t ledc_fade_func_install(int intr_alloc_flags); /** * @brief Uninstall LEDC fade function. */ void ledc_fade_func_uninstall(void); /** * @brief Start LEDC fading. * * @note Call ledc_fade_func_install() once before calling this function. * Call this API right after ledc_set_fade_with_time or ledc_set_fade_with_step before to start fading. * @note Starting fade operation with this API is not thread-safe, use with care. * @note For ESP32, hardware does not support any duty change while a fade operation is running in progress on that channel. * Other duty operations will have to wait until the fade operation has finished. * * @param speed_mode Select the LEDC channel group with specified speed mode. Note that not all targets support high speed mode. * @param channel LEDC channel number * @param fade_mode Whether to block until fading done. See ledc_types.h ledc_fade_mode_t for more info. * Note that this function will not return until fading to the target duty if LEDC_FADE_WAIT_DONE mode is selected. * * @return * - ESP_OK Success * - ESP_ERR_INVALID_STATE Channel not initialized or fade function not installed. * - ESP_ERR_INVALID_ARG Parameter error. */ esp_err_t ledc_fade_start(ledc_mode_t speed_mode, ledc_channel_t channel, ledc_fade_mode_t fade_mode); #if SOC_LEDC_SUPPORT_FADE_STOP /** * @brief Stop LEDC fading. The duty of the channel is garanteed to be fixed at most one PWM cycle after the function returns. * * @note This API can be called if a new fixed duty or a new fade want to be set while the last fade operation is still running in progress. * @note Call this API will abort the fading operation only if it was started by calling ledc_fade_start with LEDC_FADE_NO_WAIT mode. * @note If a fade was started with LEDC_FADE_WAIT_DONE mode, calling this API afterwards has no use in stopping the fade. Fade will continue until it reachs the target duty. * * @param speed_mode Select the LEDC channel group with specified speed mode. Note that not all targets support high speed mode. * @param channel LEDC channel number * * @return * - ESP_OK Success * - ESP_ERR_INVALID_STATE Channel not initialized * - ESP_ERR_INVALID_ARG Parameter error * - ESP_FAIL Fade function init error */ esp_err_t ledc_fade_stop(ledc_mode_t speed_mode, ledc_channel_t channel); #endif //SOC_LEDC_SUPPORT_FADE_STOP /** * @brief A thread-safe API to set duty for LEDC channel and return when duty updated. * * @note For ESP32, hardware does not support any duty change while a fade operation is running in progress on that channel. * Other duty operations will have to wait until the fade operation has finished. * * @param speed_mode Select the LEDC channel group with specified speed mode. Note that not all targets support high speed mode. * @param channel LEDC channel (0 - LEDC_CHANNEL_MAX-1), select from ledc_channel_t * @param duty Set the LEDC duty, the range of duty setting is [0, (2**duty_resolution)] * @param hpoint Set the LEDC hpoint value, the range is [0, (2**duty_resolution)-1] * * @return * - ESP_OK Success * - ESP_ERR_INVALID_STATE Channel not initialized * - ESP_ERR_INVALID_ARG Parameter error * - ESP_FAIL Fade function init error */ esp_err_t ledc_set_duty_and_update(ledc_mode_t speed_mode, ledc_channel_t channel, uint32_t duty, uint32_t hpoint); /** * @brief A thread-safe API to set and start LEDC fade function, with a limited time. * * @note Call ledc_fade_func_install() once, before calling this function. * @note For ESP32, hardware does not support any duty change while a fade operation is running in progress on that channel. * Other duty operations will have to wait until the fade operation has finished. * * @param speed_mode Select the LEDC channel group with specified speed mode. Note that not all targets support high speed mode. * @param channel LEDC channel index (0 - LEDC_CHANNEL_MAX-1), select from ledc_channel_t * @param target_duty Target duty of fading [0, (2**duty_resolution)] * @param max_fade_time_ms The maximum time of the fading ( ms ). * @param fade_mode choose blocking or non-blocking mode * * @return * - ESP_OK Success * - ESP_ERR_INVALID_ARG Parameter error * - ESP_ERR_INVALID_STATE Channel not initialized * - ESP_FAIL Fade function init error */ esp_err_t ledc_set_fade_time_and_start(ledc_mode_t speed_mode, ledc_channel_t channel, uint32_t target_duty, uint32_t max_fade_time_ms, ledc_fade_mode_t fade_mode); /** * @brief A thread-safe API to set and start LEDC fade function. * * @note Call ledc_fade_func_install() once before calling this function. * @note For ESP32, hardware does not support any duty change while a fade operation is running in progress on that channel. * Other duty operations will have to wait until the fade operation has finished. * * @param speed_mode Select the LEDC channel group with specified speed mode. Note that not all targets support high speed mode. * @param channel LEDC channel index (0 - LEDC_CHANNEL_MAX-1), select from ledc_channel_t * @param target_duty Target duty of fading [0, (2**duty_resolution)] * @param scale Controls the increase or decrease step scale. * @param cycle_num increase or decrease the duty every cycle_num cycles * @param fade_mode choose blocking or non-blocking mode * * @return * - ESP_OK Success * - ESP_ERR_INVALID_ARG Parameter error * - ESP_ERR_INVALID_STATE Channel not initialized * - ESP_FAIL Fade function init error */ esp_err_t ledc_set_fade_step_and_start(ledc_mode_t speed_mode, ledc_channel_t channel, uint32_t target_duty, uint32_t scale, uint32_t cycle_num, ledc_fade_mode_t fade_mode); /** * @brief LEDC callback registration function * * @note The callback is called from an ISR, it must never attempt to block, and any FreeRTOS API called must be ISR capable. * * @param speed_mode Select the LEDC channel group with specified speed mode. Note that not all targets support high speed mode. * @param channel LEDC channel index (0 - LEDC_CHANNEL_MAX-1), select from ledc_channel_t * @param cbs Group of LEDC callback functions * @param user_arg user registered data for the callback function * * @return * - ESP_OK Success * - ESP_ERR_INVALID_ARG Parameter error * - ESP_ERR_INVALID_STATE Channel not initialized * - ESP_FAIL Fade function init error */ esp_err_t ledc_cb_register(ledc_mode_t speed_mode, ledc_channel_t channel, ledc_cbs_t *cbs, void *user_arg); #if SOC_LEDC_GAMMA_CURVE_FADE_SUPPORTED /** * @brief Structure for the fade parameters for one hardware fade to be written to gamma wr register * * @verbatim * duty ^ ONE HW LINEAR FADE * | * | * | * | * start_duty + scale * n = end_duty |. . . . . . . . . . . . . . . . . . . . . . . . . .+- * | | * | | * | +--------+ * | | . * | | . * | -------+ . * | . . * | . . * | . . * | . . * ^ --- |. . . . . . . . . .+-------- . * scale| | | . * | | | . * v --- |. . . . .+---------+ . * | | . . * | | . . * start_duty +---------+ . . * | . . . * | . . . * +-----------------------------------------------------------> * PWM cycle * | | | | * | 1 step | 1 step | | * |<------->|<------->| | * | m cycles m cycles | * | | * <---------------------------------------------------> * n total steps * cycles = m * n * @endverbatim * * @note Be aware of the maximum value available on each element */ typedef struct { uint32_t dir : 1; /*!< Duty change direction. Set 1 as increase, 0 as decrease */ uint32_t cycle_num : SOC_LEDC_FADE_PARAMS_BIT_WIDTH; /*!< Number of PWM cycles of each step [0, 2**SOC_LEDC_FADE_PARAMS_BIT_WIDTH-1] */ uint32_t scale : SOC_LEDC_FADE_PARAMS_BIT_WIDTH; /*!< Duty change of each step [0, 2**SOC_LEDC_FADE_PARAMS_BIT_WIDTH-1] */ uint32_t step_num : SOC_LEDC_FADE_PARAMS_BIT_WIDTH; /*!< Total number of steps in one hardware fade [0, 2**SOC_LEDC_FADE_PARAMS_BIT_WIDTH-1] */ } ledc_fade_param_config_t; /** * @brief Set a LEDC multi-fade * * @note Call `ledc_fade_func_install()` once before calling this function. * Call `ledc_fade_start()` after this to start fading. * @note This function is not thread-safe, do not call it to control one LEDC channel in different tasks at the same time. * A thread-safe version of API is ledc_set_multi_fade_and_start * @note This function does not prohibit from duty overflow. User should take care of this by themselves. If duty * overflow happens, the PWM signal will suddenly change from 100% duty cycle to 0%, or the other way around. * * @param speed_mode Select the LEDC channel group with specified speed mode. Note that not all targets support high speed mode. * @param channel LEDC channel index (0 - LEDC_CHANNEL_MAX-1), select from ledc_channel_t * @param start_duty Set the start of the gradient duty, the range of duty setting is [0, (2**duty_resolution)] * @param fade_params_list Pointer to the array of fade parameters for a multi-fade * @param list_len Length of the fade_params_list, i.e. number of fade ranges for a multi-fade (1 - SOC_LEDC_GAMMA_CURVE_FADE_RANGE_MAX) * * @return * - ESP_OK Success * - ESP_ERR_INVALID_ARG Parameter error * - ESP_ERR_INVALID_STATE Channel not initialized * - ESP_FAIL Fade function init error */ esp_err_t ledc_set_multi_fade(ledc_mode_t speed_mode, ledc_channel_t channel, uint32_t start_duty, const ledc_fade_param_config_t *fade_params_list, uint32_t list_len); /** * @brief A thread-safe API to set and start LEDC multi-fade function * * @note Call `ledc_fade_func_install()` once before calling this function. * @note Fade will always begin from the current duty cycle. Make sure it is stable and synchronized to the desired * initial value before calling this function. Otherwise, you may see unexpected duty change. * @note This function does not prohibit from duty overflow. User should take care of this by themselves. If duty * overflow happens, the PWM signal will suddenly change from 100% duty cycle to 0%, or the other way around. * * @param speed_mode Select the LEDC channel group with specified speed mode. Note that not all targets support high speed mode. * @param channel LEDC channel index (0 - LEDC_CHANNEL_MAX-1), select from ledc_channel_t * @param start_duty Set the start of the gradient duty, the range of duty setting is [0, (2**duty_resolution)] * @param fade_params_list Pointer to the array of fade parameters for a multi-fade * @param list_len Length of the fade_params_list, i.e. number of fade ranges for a multi-fade (1 - SOC_LEDC_GAMMA_CURVE_FADE_RANGE_MAX) * @param fade_mode Choose blocking or non-blocking mode * * @return * - ESP_OK Success * - ESP_ERR_INVALID_ARG Parameter error * - ESP_ERR_INVALID_STATE Channel not initialized * - ESP_FAIL Fade function init error */ esp_err_t ledc_set_multi_fade_and_start(ledc_mode_t speed_mode, ledc_channel_t channel, uint32_t start_duty, const ledc_fade_param_config_t *fade_params_list, uint32_t list_len, ledc_fade_mode_t fade_mode); /** * @brief Helper function to fill the fade params for a multi-fade. Useful if desires a gamma curve fading. * * @note The fade params are calculated based on the given start_duty and end_duty. If the duty is not at * the start duty (gamma-corrected) when the fade begins, you may see undesired brightness change. * Therefore, please always remember thet when passing the fade_params to either `ledc_set_multi_fade` or * `ledc_set_multi_fade_and start`, the start_duty argument has to be the gamma-corrected start_duty. * * @param[in] speed_mode Select the LEDC channel group with specified speed mode. Note that not all targets support high speed mode. * @param[in] channel LEDC channel index (0 - LEDC_CHANNEL_MAX-1), select from ledc_channel_t * @param[in] start_duty Duty cycle [0, (2**duty_resolution)] where the multi-fade begins with. This value should be a non-gamma-corrected duty cycle. * @param[in] end_duty Duty cycle [0, (2**duty_resolution)] where the multi-fade ends with. This value should be a non-gamma-corrected duty cycle. * @param[in] linear_phase_num Number of linear fades to simulate a gamma curved fade (1 - SOC_LEDC_GAMMA_CURVE_FADE_RANGE_MAX) * @param[in] max_fade_time_ms The maximum time of the fading ( ms ). * @param[in] gamma_correction_operator User provided gamma correction function. The function argument should be able to * take any value within [0, (2**duty_resolution)]. And returns the gamma-corrected duty cycle. * @param[in] fade_params_list_size The size of the fade_params_list user allocated (1 - SOC_LEDC_GAMMA_CURVE_FADE_RANGE_MAX) * @param[out] fade_params_list Pointer to the array of ledc_fade_param_config_t structure * @param[out] hw_fade_range_num Number of fade ranges for this multi-fade * * @return * - ESP_OK Success * - ESP_ERR_INVALID_ARG Parameter error * - ESP_ERR_INVALID_STATE Channel not initialized * - ESP_FAIL Required number of hardware ranges exceeds the size of the ledc_fade_param_config_t array user allocated */ esp_err_t ledc_fill_multi_fade_param_list(ledc_mode_t speed_mode, ledc_channel_t channel, uint32_t start_duty, uint32_t end_duty, uint32_t linear_phase_num, uint32_t max_fade_time_ms, uint32_t (* gamma_correction_operator)(uint32_t), uint32_t fade_params_list_size, ledc_fade_param_config_t *fade_params_list, uint32_t *hw_fade_range_num); /** * @brief Get the fade parameters that are stored in gamma ram for a certain fade range * * Gamma ram is where saves the fade parameters for each fade range. The fade parameters are written in during fade * configuration. When fade begins, the duty will change according to the parameters in gamma ram. * * @param[in] speed_mode Select the LEDC channel group with specified speed mode. Note that not all targets support high speed mode. * @param[in] channel LEDC channel index (0 - LEDC_CHANNEL_MAX-1), select from ledc_channel_t * @param[in] range Range index (0 - (SOC_LEDC_GAMMA_CURVE_FADE_RANGE_MAX-1)), it specifies to which range in gamma ram to read * @param[out] dir Pointer to accept fade direction value * @param[out] cycle Pointer to accept fade cycle value * @param[out] scale Pointer to accept fade scale value * @param[out] step Pointer to accept fade step value * * @return * - ESP_OK Success * - ESP_ERR_INVALID_ARG Parameter error * - ESP_ERR_INVALID_STATE Channel not initialized */ esp_err_t ledc_read_fade_param(ledc_mode_t speed_mode, ledc_channel_t channel, uint32_t range, uint32_t *dir, uint32_t *cycle, uint32_t *scale, uint32_t *step); #endif // SOC_LEDC_GAMMA_CURVE_FADE_SUPPORTED #ifdef __cplusplus } #endif