/* * SPDX-FileCopyrightText: 2018-2021 Espressif Systems (Shanghai) CO LTD * * SPDX-License-Identifier: Apache-2.0 */ #include #include "sdkconfig.h" #include "esp_system.h" #include "esp_private/system_internal.h" #include "esp_attr.h" #include "esp_efuse.h" #include "esp_log.h" #include "riscv/rv_utils.h" #include "esp_rom_uart.h" #include "soc/gpio_reg.h" #include "soc/timer_group_reg.h" #include "esp_cpu.h" #include "soc/rtc.h" #include "esp_private/rtc_clk.h" #include "soc/rtc_periph.h" #include "soc/syscon_reg.h" #include "soc/system_reg.h" #include "soc/uart_reg.h" #include "hal/wdt_hal.h" #include "esp_private/cache_err_int.h" #include "esp32c3/rom/cache.h" #include "esp32c3/rom/rtc.h" void IRAM_ATTR esp_system_reset_modules_on_exit(void) { // Flush any data left in UART FIFOs before reset the UART peripheral esp_rom_uart_tx_wait_idle(0); esp_rom_uart_tx_wait_idle(1); // Reset wifi/bluetooth/ethernet/sdio (bb/mac) SET_PERI_REG_MASK(SYSTEM_CORE_RST_EN_REG, SYSTEM_WIFIBB_RST | SYSTEM_FE_RST | SYSTEM_WIFIMAC_RST | SYSTEM_SDIO_RST | SYSTEM_EMAC_RST | SYSTEM_MACPWR_RST | SYSTEM_BTBB_RST | SYSTEM_BTBB_REG_RST | SYSTEM_RW_BTMAC_RST | SYSTEM_RW_BTLP_RST | SYSTEM_RW_BTMAC_REG_RST | SYSTEM_RW_BTLP_REG_RST); REG_WRITE(SYSTEM_CORE_RST_EN_REG, 0); // Reset uart0 core first, then reset apb side. // rom will clear this bit, as well as SYSTEM_UART_RST SET_PERI_REG_MASK(UART_CLK_CONF_REG(0), UART_RST_CORE_M); // Reset timer/spi/uart SET_PERI_REG_MASK(SYSTEM_PERIP_RST_EN0_REG, SYSTEM_TIMERS_RST | SYSTEM_SPI01_RST | SYSTEM_UART_RST | SYSTEM_SYSTIMER_RST); REG_WRITE(SYSTEM_PERIP_RST_EN0_REG, 0); // Reset dma SET_PERI_REG_MASK(SYSTEM_PERIP_RST_EN1_REG, SYSTEM_DMA_RST); REG_WRITE(SYSTEM_PERIP_RST_EN1_REG, 0); } /* "inner" restart function for after RTOS, interrupts & anything else on this * core are already stopped. Stalls other core, resets hardware, * triggers restart. */ void IRAM_ATTR esp_restart_noos(void) { // Disable interrupts rv_utils_intr_global_disable(); // Enable RTC watchdog for 1 second wdt_hal_context_t rtc_wdt_ctx; wdt_hal_init(&rtc_wdt_ctx, WDT_RWDT, 0, false); uint32_t stage_timeout_ticks = (uint32_t)(1000ULL * rtc_clk_slow_freq_get_hz() / 1000ULL); wdt_hal_write_protect_disable(&rtc_wdt_ctx); wdt_hal_config_stage(&rtc_wdt_ctx, WDT_STAGE0, stage_timeout_ticks, WDT_STAGE_ACTION_RESET_SYSTEM); wdt_hal_config_stage(&rtc_wdt_ctx, WDT_STAGE1, stage_timeout_ticks, WDT_STAGE_ACTION_RESET_RTC); //Enable flash boot mode so that flash booting after restart is protected by the RTC WDT. wdt_hal_set_flashboot_en(&rtc_wdt_ctx, true); wdt_hal_write_protect_enable(&rtc_wdt_ctx); // Disable TG0/TG1 watchdogs wdt_hal_context_t wdt0_context = {.inst = WDT_MWDT0, .mwdt_dev = &TIMERG0}; wdt_hal_write_protect_disable(&wdt0_context); wdt_hal_disable(&wdt0_context); wdt_hal_write_protect_enable(&wdt0_context); wdt_hal_context_t wdt1_context = {.inst = WDT_MWDT1, .mwdt_dev = &TIMERG1}; wdt_hal_write_protect_disable(&wdt1_context); wdt_hal_disable(&wdt1_context); wdt_hal_write_protect_enable(&wdt1_context); // Disable cache Cache_Disable_ICache(); // 2nd stage bootloader reconfigures SPI flash signals. // Reset them to the defaults expected by ROM. WRITE_PERI_REG(GPIO_FUNC0_IN_SEL_CFG_REG, 0x30); WRITE_PERI_REG(GPIO_FUNC1_IN_SEL_CFG_REG, 0x30); WRITE_PERI_REG(GPIO_FUNC2_IN_SEL_CFG_REG, 0x30); WRITE_PERI_REG(GPIO_FUNC3_IN_SEL_CFG_REG, 0x30); WRITE_PERI_REG(GPIO_FUNC4_IN_SEL_CFG_REG, 0x30); WRITE_PERI_REG(GPIO_FUNC5_IN_SEL_CFG_REG, 0x30); esp_system_reset_modules_on_exit(); // Set CPU back to XTAL source, same as hard reset, but keep BBPLL on so that USB Serial JTAG can log at 1st stage bootloader. #if !CONFIG_IDF_ENV_FPGA rtc_clk_cpu_set_to_default_config(); #endif // Reset CPU esp_rom_software_reset_cpu(0); while (true) { ; } }