menu "Hardware Settings" menu "Chip revision" # Insert chip-specific HW config orsource "./port/$IDF_TARGET/Kconfig.hw_support" endmenu orsource "./port/$IDF_TARGET/Kconfig.spiram" menu "MAC Config" config ESP_MAC_ADDR_UNIVERSE_WIFI_STA bool config ESP_MAC_ADDR_UNIVERSE_WIFI_AP bool config ESP_MAC_ADDR_UNIVERSE_BT bool config ESP_MAC_ADDR_UNIVERSE_ETH bool config ESP_MAC_ADDR_UNIVERSE_IEEE802154 bool config ESP_MAC_UNIVERSAL_MAC_ADDRESSES_ONE bool config ESP_MAC_UNIVERSAL_MAC_ADDRESSES_TWO bool config ESP_MAC_UNIVERSAL_MAC_ADDRESSES_FOUR bool # Insert chip-specific MAC config orsource "./port/$IDF_TARGET/Kconfig.mac" endmenu menu "Sleep Config" # This is here since this option affect behavior of esp_light_sleep_start # regardless of power management configuration. config ESP_SLEEP_POWER_DOWN_FLASH bool "Power down flash in light sleep when there is no SPIRAM" depends on !SPIRAM default n help If enabled, chip will try to power down flash as part of esp_light_sleep_start(), which costs more time when chip wakes up. Can only be enabled if there is no SPIRAM configured. This option will power down flash under a strict but relatively safe condition. Also, it is possible to power down flash under a relaxed condition by using esp_sleep_pd_config() to set ESP_PD_DOMAIN_VDDSDIO to ESP_PD_OPTION_OFF. It should be noted that there is a risk in powering down flash, you can refer `ESP-IDF Programming Guide/API Reference/System API/Sleep Modes/Power-down of Flash` for more details. config ESP_SLEEP_RTC_BUS_ISO_WORKAROUND bool default y if IDF_TARGET_ESP32 || IDF_TARGET_ESP32S2 || IDF_TARGET_ESP32S3 config ESP_SLEEP_GPIO_RESET_WORKAROUND bool "light sleep GPIO reset workaround" default y if IDF_TARGET_ESP32C2 || IDF_TARGET_ESP32C3 || IDF_TARGET_ESP32S3 # TODO: IDF-5641 (esp32c6) select PM_SLP_DISABLE_GPIO if FREERTOS_USE_TICKLESS_IDLE help esp32c2, esp32c3 and esp32s3 will reset at wake-up if GPIO is received a small electrostatic pulse during light sleep, with specific condition - GPIO needs to be configured as input-mode only - The pin receives a small electrostatic pulse, and reset occurs when the pulse voltage is higher than 6 V For GPIO set to input mode only, it is not a good practice to leave it open/floating, The hardware design needs to controlled it with determined supply or ground voltage is necessary. This option provides a software workaround for this issue. Configure to isolate all GPIO pins in sleep state. config ESP_SLEEP_PSRAM_LEAKAGE_WORKAROUND bool "PSRAM leakage current workaround in light sleep" depends on SPIRAM default y help When the CS pin of SPIRAM is not pulled up, the sleep current will increase during light sleep. If the CS pin of SPIRAM has an external pull-up, you do not need to select this option, otherwise, you should enable this option. config ESP_SLEEP_FLASH_LEAKAGE_WORKAROUND bool "Flash leakage current workaround in light sleep" default y help When the CS pin of Flash is not pulled up, the sleep current will increase during light sleep. If the CS pin of Flash has an external pull-up, you do not need to select this option, otherwise, you should enable this option. config ESP_SLEEP_MSPI_NEED_ALL_IO_PU bool "All pins of mspi need pull up" depends on ESP_SLEEP_PSRAM_LEAKAGE_WORKAROUND || ESP_SLEEP_FLASH_LEAKAGE_WORKAROUND default y if IDF_TARGET_ESP32C2 || IDF_TARGET_ESP32S3 help To reduce leakage current, some types of SPI Flash/RAM only need to pull up the CS pin during light sleep. But there are also some kinds of SPI Flash/RAM that need to pull up all pins. It depends on the SPI Flash/RAM chip used. config ESP_SLEEP_DEEP_SLEEP_WAKEUP_DELAY int "Extra delay in deep sleep wake stub (in us)" depends on IDF_TARGET_ESP32 || IDF_TARGET_ESP32S3 default 2000 range 0 5000 help When the chip exits deep sleep, the CPU and the flash chip are powered on at the same time. CPU will run deep sleep stub first, and then proceed to load code from flash. Some flash chips need sufficient time to pass between power on and first read operation. By default, without any extra delay, this time is approximately 900us, although some flash chip types need more than that. By default extra delay is set to 2000us. When optimizing startup time for applications which require it, this value may be reduced. If you are seeing "flash read err, 1000" message printed to the console after deep sleep reset, try increasing this value. endmenu menu "RTC Clock Config" orsource "./port/$IDF_TARGET/Kconfig.rtc" config RTC_CLOCK_BBPLL_POWER_ON_WITH_USB # This is used for configure the RTC clock. bool "Keep BBPLL clock always work" depends on ESP_CONSOLE_USB_SERIAL_JTAG || ESP_CONSOLE_SECONDARY_USB_SERIAL_JTAG default y help When software switches the CPU clock source from BBPLL clock to XTAL, usually the BBPLL will be switched off. This helps to save some power consumption in sleep modes. However this may also happen during the software reset, resulting in the inactive (disconnected from host) of the USB_SERIAL_JTAG device during software reset. When USB_SERIAL_JTAG is being used, whether to turn off the clock source during software reset and in sleep modes is determined by RTC_CLOCK_BBPLL_POWER_ON_WITH_USB. - When RTC_CLOCK_BBPLL_POWER_ON_WITH_USB is enabled, the clock will be kept, so that the USB_SERIAL_JTAG will keep alive during software reset. The side-effect is the increasing of power consumption during sleep modes, even though USB_SERIAL_JTAG will not work in sleep modes. - When RTC_CLOCK_BBPLL_POWER_ON_WITH_USB is disabled, the clock will be turned off. USB_SERIAL_JTAG will be inactive during software reset and in sleep modes. This saves some power consumption in sleep modes. When USB_SERIAL_JTAG is not being used, software will always turn off BBPLL regardless of RTC_CLOCK_BBPLL_POWER_ON_WITH_USB is set or not. endmenu menu "Peripheral Control" config PERIPH_CTRL_FUNC_IN_IRAM bool "Place peripheral control functions into IRAM" default n help Place peripheral control functions (e.g. periph_module_reset) into IRAM, so that these functions can be IRAM-safe and able to be called in the other IRAM interrupt context. endmenu menu "ETM Configuration" depends on SOC_ETM_SUPPORTED config ETM_ENABLE_DEBUG_LOG bool "Enable debug log" default n help Wether to enable the debug log message for ETM core driver. Note that, this option only controls the ETM related driver log, won't affect other drivers. endmenu # ETM Configuration menu "MMU Config" # This Config is used for configure the MMU. # Be configured based on flash size selection. # Invisible to users. config MMU_PAGE_SIZE_16KB bool default y if IDF_TARGET_ESP32C2 && ESPTOOLPY_FLASHSIZE_1MB default n config MMU_PAGE_SIZE_32KB bool default y if IDF_TARGET_ESP32C2 && ESPTOOLPY_FLASHSIZE_2MB default n config MMU_PAGE_SIZE_64KB bool default y if !MMU_PAGE_SIZE_32KB && !MMU_PAGE_SIZE_16KB default n config MMU_PAGE_MODE string default "8KB" if MMU_PAGE_SIZE_8KB default "16KB" if MMU_PAGE_SIZE_16KB default "32KB" if MMU_PAGE_SIZE_32KB default "64KB" if MMU_PAGE_SIZE_64KB config MMU_PAGE_SIZE # Some chips support different flash MMU page sizes: 64k, 32k, 16k. # Since the number of MMU pages is limited, the maximum flash size supported # for each page size is reduced proportionally: 4 MB, 2MB, 1MB. To make best # use of small flash sizes (reducing the wasted space due to alignment), we # need to use the smallest possible MMU page size for the given flash size. hex default 0x2000 if MMU_PAGE_SIZE_8KB default 0x4000 if MMU_PAGE_SIZE_16KB default 0x8000 if MMU_PAGE_SIZE_32KB default 0x10000 if MMU_PAGE_SIZE_64KB endmenu menu "GDMA Configuration" depends on SOC_GDMA_SUPPORTED config GDMA_CTRL_FUNC_IN_IRAM bool "Place GDMA control functions into IRAM" default n help Place GDMA control functions (like start/stop/append/reset) into IRAM, so that these functions can be IRAM-safe and able to be called in the other IRAM interrupt context. Enabling this option can improve driver performance as well. config GDMA_ISR_IRAM_SAFE bool "GDMA ISR IRAM-Safe" default n help This will ensure the GDMA interrupt handler is IRAM-Safe, allow to avoid flash cache misses, and also be able to run whilst the cache is disabled. (e.g. SPI Flash write). endmenu # GDMA Configuration menu "Main XTAL Config" choice XTAL_FREQ_SEL prompt "Main XTAL frequency" default XTAL_FREQ_40 if SOC_XTAL_SUPPORT_40M help This option selects the operating frequency of the XTAL (crystal) clock used to drive the ESP target. The selected value MUST reflect the frequency of the given hardware. Note: The XTAL_FREQ_AUTO option allows the ESP target to automatically estimating XTAL clock's operating frequency. However, this feature is only supported on the ESP32. The ESP32 uses the internal 8MHZ as a reference when estimating. Due to the internal oscillator's frequency being temperature dependent, usage of the XTAL_FREQ_AUTO is not recommended in applications that operate in high ambient temperatures or use high-temperature qualified chips and modules. config XTAL_FREQ_24 depends on SOC_XTAL_SUPPORT_24M bool "24 MHz" config XTAL_FREQ_26 depends on SOC_XTAL_SUPPORT_26M bool "26 MHz" config XTAL_FREQ_32 depends on SOC_XTAL_SUPPORT_32M bool "32 MHz" config XTAL_FREQ_40 depends on SOC_XTAL_SUPPORT_40M bool "40 MHz" config XTAL_FREQ_AUTO depends on SOC_XTAL_SUPPORT_AUTO_DETECT bool "Autodetect" endchoice # rtc_xtal_freq_t enum in soc/rtc.h lists the XTAL frequencies can be supported # SOC_XTAL_SUPPORT_XXX in soc_caps.h lists the XTAL frequencies already supported config XTAL_FREQ int default 24 if XTAL_FREQ_24 default 26 if XTAL_FREQ_26 default 32 if XTAL_FREQ_32 default 40 if XTAL_FREQ_40 default 0 if XTAL_FREQ_AUTO endmenu endmenu