# I2C Self-Test Example (See the README.md file in the upper level 'examples' directory for more information about examples.) ## Overview This example demonstrates basic usage of I2C driver by running two tasks on I2C bus: 1. Read external I2C sensor, here we take the BH1750 ambient light sensor (GY-30 module) for an example. 2. Use one of the ESP device's I2C port (master mode) to read and write another I2C port (slave mode) in ESP device. If you have a new I2C application to go (for example, read the temperature data from external sensor with I2C interface), try this as a basic template, then add your own code. ## How to use example ### Hardware Required To run this example, you should have one ESP development board (e.g. ESP32-WROVER Kit) or ESP core board (e.g. ESP32-DevKitC). Optionally, you can also connect an external sensor. Here we choose the BH1750 just as an example. BH1750 is a digital ambient light sensor. For more information about it, you can read the [datasheet](http://rohmfs.rohm.com/en/products/databook/datasheet/ic/sensor/light/bh1721fvc-e.pdf) of this sensor. #### Pin Assignment(esp32, esp32s2): **Note:** The following pin assignments are used by default, you can change these in the `menuconfig` . | | SDA | SCL | | ------------------------- | ------ | ------ | | ESP32/ESP32-S2 I2C Master | GPIO18 | GPIO19 | | ESP32/ESP32-S2 I2C Slave | GPIO4 | GPIO5 | | BH1750 Sensor | SDA | SCL | - slave: - GPIO4 is assigned as the data signal of I2C slave port - GPIO5 is assigned as the clock signal of I2C slave port - master: - GPIO18 is assigned as the data signal of I2C master port - GPIO19 is assigned as the clock signal of I2C master port - Connection: - connect GPIO18 with GPIO4 - connect GPIO19 with GPIO5 - connect SDA/SCL of BH1750 sensor with GPIO18/GPIO19 **Note:** It is recommended to add external pull-up resistors for SDA/SCL pins to make the communication more stable, though the driver will enable internal pull-up resistors. #### Pin Assignment(esp32s3): **Note:** The following pin assignments are used by default, you can change these in the `menuconfig` . | | SDA | SCL | | ------------------------- | ------ | ------ | | ESP32-S3 I2C Master | GPIO1 | GPIO2 | | ESP32-S3 I2C Slave | GPIO4 | GPIO5 | | BH1750 Sensor | SDA | SCL | - slave: - GPIO4 is assigned as the data signal of I2C slave port - GPIO5 is assigned as the clock signal of I2C slave port - master: - GPIO1 is assigned as the data signal of I2C master port - GPIO2 is assigned as the clock signal of I2C master port - Connection: - connect GPIO1 with GPIO4 - connect GPIO2 with GPIO5 - connect SDA/SCL of BH1750 sensor with GPIO18/GPIO19 **Note:** It is recommended to add external pull-up resistors for SDA/SCL pins to make the communication more stable, though the driver will enable internal pull-up resistors. #### Pin Assignment(esp32c3, esp32c2, esp32h2): **Note:** The following pin assignments are used by default, you can change these in the `menuconfig` . | | SDA | SCL | | ------------------------------------------- | ------ | ------ | | ESP32-C3/ESP32-C2/ESP32-H2 I2C Master(Slave)| GPIO5 | GPIO6 | | BH1750 Sensor | SDA | SCL | - master: - GPIO5 is assigned to the data signal of the I2C master port - GPIO6 is assigned to the clock signal of the I2C master port - Connection: - connect SDA/SCL of BH1750 sensor to GPIO5/GPIO6 **Note:** There is only one i2c device on ESP32-C3/ESP32-C2/ESP32-H2, so it is not possible to perform any ESP32/ESP32-S2 self-test example from this repo. However it is possible to test I2C with external devices. If you find anything wrong with your device, please try connecting external pull-up resistors. ### Configure the project Open the project configuration menu (`idf.py menuconfig`). Then go into `Example Configuration` menu. - In the `I2C Master` submenu, you can set the pin number of SDA/SCL according to your board. Also you can modify the I2C port number and freauency of the master. - In the `I2C Slave` submenu, you can set the pin number of SDA/SCL according to your board. Also you can modify the I2C port number and address of the slave. - In the `BH1750 Sensor` submenu, you can choose the slave address of BH1750 accroding to the pin level of ADDR pin (if the pin level of ADDR is low then the address is `0x23`, otherwise it is `0x5c`). Here you can also control the operation mode of BH1750, each mode has a different resolution and measurement time. For example, in the `One Time L-Resolution` mode, the resolution is 4 Lux and measurement time is typically 16ms (higher resolution means longer measurement time). For more information, you can consult the datasheet of BH1750. ### Build and Flash Enter `idf.py -p PORT flash monitor` to build, flash and monitor the project. (To exit the serial monitor, type ``Ctrl-]``.) See the [Getting Started Guide](https://docs.espressif.com/projects/esp-idf/en/latest/get-started/index.html) for full steps to configure and use ESP-IDF to build projects. ## Example Output ```bash I (6495) i2c-example: TASK[1] test cnt: 1 ******************* TASK[1] MASTER READ SENSOR( BH1750 ) ******************* data_h: 01 data_l: d0 sensor val: 386.67 [Lux] I (6695) i2c-example: TASK[0] test cnt: 2 ******************* TASK[0] MASTER READ SENSOR( BH1750 ) ******************* data_h: 01 data_l: d0 sensor val: 386.67 [Lux] ******************* TASK[0] MASTER READ FROM SLAVE ******************* ====TASK[0] Slave buffer data ==== 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16 17 18 19 1a 1b 1c 1d 1e 1f 20 21 22 23 24 25 26 27 28 29 2a 2b 2c 2d 2e 2f 30 31 32 33 34 35 36 37 38 39 3a 3b 3c 3d 3e 3f 40 41 42 43 44 45 46 47 48 49 4a 4b 4c 4d 4e 4f 50 51 52 53 54 55 56 57 58 59 5a 5b 5c 5d 5e 5f 60 61 62 63 64 65 66 67 68 69 6a 6b 6c 6d 6e 6f 70 71 72 73 74 75 76 77 78 79 7a 7b 7c 7d 7e 7f ====TASK[0] Master read ==== 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16 17 18 19 1a 1b 1c 1d 1e 1f 20 21 22 23 24 25 26 27 28 29 2a 2b 2c 2d 2e 2f 30 31 32 33 34 35 36 37 38 39 3a 3b 3c 3d 3e 3f 40 41 42 43 44 45 46 47 48 49 4a 4b 4c 4d 4e 4f 50 51 52 53 54 55 56 57 58 59 5a 5b 5c 5d 5e 5f 60 61 62 63 64 65 66 67 68 69 6a 6b 6c 6d 6e 6f 70 71 72 73 74 75 76 77 78 79 7a 7b 7c 7d 7e 7f ******************* TASK[1] MASTER READ FROM SLAVE ******************* ====TASK[1] Slave buffer data ==== 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16 17 18 19 1a 1b 1c 1d 1e 1f 20 21 22 23 24 25 26 27 28 29 2a 2b 2c 2d 2e 2f 30 31 32 33 34 35 36 37 38 39 3a 3b 3c 3d 3e 3f 40 41 42 43 44 45 46 47 48 49 4a 4b 4c 4d 4e 4f 50 51 52 53 54 55 56 57 58 59 5a 5b 5c 5d 5e 5f 60 61 62 63 64 65 66 67 68 69 6a 6b 6c 6d 6e 6f 70 71 72 73 74 75 76 77 78 79 7a 7b 7c 7d 7e 7f ====TASK[1] Master read ==== 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16 17 18 19 1a 1b 1c 1d 1e 1f 20 21 22 23 24 25 26 27 28 29 2a 2b 2c 2d 2e 2f 30 31 32 33 34 35 36 37 38 39 3a 3b 3c 3d 3e 3f 40 41 42 43 44 45 46 47 48 49 4a 4b 4c 4d 4e 4f 50 51 52 53 54 55 56 57 58 59 5a 5b 5c 5d 5e 5f 60 61 62 63 64 65 66 67 68 69 6a 6b 6c 6d 6e 6f 70 71 72 73 74 75 76 77 78 79 7a 7b 7c 7d 7e 7f ******************* TASK[0] MASTER WRITE TO SLAVE ******************* ----TASK[0] Master write ---- 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16 17 18 19 1a 1b 1c 1d 1e 1f 20 21 22 23 24 25 26 27 28 29 2a 2b 2c 2d 2e 2f 30 31 32 33 34 35 36 37 38 39 3a 3b 3c 3d 3e 3f 40 41 42 43 44 45 46 47 48 49 4a 4b 4c 4d 4e 4f 50 51 52 53 54 55 56 57 58 59 5a 5b 5c 5d 5e 5f 60 61 62 63 64 65 66 67 68 69 6a 6b 6c 6d 6e 6f 70 71 72 73 74 75 76 77 78 79 7a 7b 7c 7d 7e 7f 80 81 82 83 84 85 86 87 88 89 ----TASK[0] Slave read: [128] bytes ---- 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16 17 18 19 1a 1b 1c 1d 1e 1f 20 21 22 23 24 25 26 27 28 29 2a 2b 2c 2d 2e 2f 30 31 32 33 34 35 36 37 38 39 3a 3b 3c 3d 3e 3f 40 41 42 43 44 45 46 47 48 49 4a 4b 4c 4d 4e 4f 50 51 52 53 54 55 56 57 58 59 5a 5b 5c 5d 5e 5f 60 61 62 63 64 65 66 67 68 69 6a 6b 6c 6d 6e 6f 70 71 72 73 74 75 76 77 78 79 7a 7b 7c 7d 7e 7f 80 81 82 83 84 85 86 87 88 89 ``` ## Troubleshooting - BH1750 has two I2C address, which is decided by the voltage level of `ADDR` pin at start up. Make sure to check your schemetic before run this example. (For any technical queries, please open an [issue](https://github.com/espressif/esp-idf/issues) on GitHub. We will get back to you as soon as possible.)