menu "ESP32-specific" # TODO: this component simply shouldn't be included # in the build at the CMake level, but this is currently # not working so we just hide all items here visible if IDF_TARGET_ESP32 config ESP32_ECO3_CACHE_LOCK_FIX bool default y depends on !FREERTOS_UNICORE && ESP32_SPIRAM_SUPPORT choice ESP32_REV_MIN prompt "Minimum Supported ESP32 Revision" default ESP32_REV_MIN_0 help Minimum revision that ESP-IDF would support. ESP-IDF performs different strategy on different esp32 revision. config ESP32_REV_MIN_0 bool "Rev 0" config ESP32_REV_MIN_1 bool "Rev 1" config ESP32_REV_MIN_2 bool "Rev 2" config ESP32_REV_MIN_3 bool "Rev 3" select ESP_INT_WDT if ESP32_ECO3_CACHE_LOCK_FIX endchoice config ESP32_REV_MIN int default 0 if ESP32_REV_MIN_0 default 1 if ESP32_REV_MIN_1 default 2 if ESP32_REV_MIN_2 default 3 if ESP32_REV_MIN_3 config ESP32_DPORT_WORKAROUND bool default "y" if !FREERTOS_UNICORE && ESP32_REV_MIN < 2 choice ESP32_DEFAULT_CPU_FREQ_MHZ prompt "CPU frequency" default ESP32_DEFAULT_CPU_FREQ_160 help CPU frequency to be set on application startup. config ESP32_DEFAULT_CPU_FREQ_80 bool "80 MHz" config ESP32_DEFAULT_CPU_FREQ_160 bool "160 MHz" config ESP32_DEFAULT_CPU_FREQ_240 bool "240 MHz" endchoice config ESP32_DEFAULT_CPU_FREQ_MHZ int default 80 if ESP32_DEFAULT_CPU_FREQ_80 default 160 if ESP32_DEFAULT_CPU_FREQ_160 default 240 if ESP32_DEFAULT_CPU_FREQ_240 # Note: to support SPIRAM across multiple chips, check CONFIG_SPIRAM # instead config ESP32_SPIRAM_SUPPORT bool "Support for external, SPI-connected RAM" default "n" select SPIRAM help This enables support for an external SPI RAM chip, connected in parallel with the main SPI flash chip. menu "SPI RAM config" depends on ESP32_SPIRAM_SUPPORT choice SPIRAM_TYPE prompt "Type of SPI RAM chip in use" default SPIRAM_TYPE_AUTO config SPIRAM_TYPE_AUTO bool "Auto-detect" config SPIRAM_TYPE_ESPPSRAM16 bool "ESP-PSRAM16 or APS1604" config SPIRAM_TYPE_ESPPSRAM32 bool "ESP-PSRAM32 or IS25WP032" config SPIRAM_TYPE_ESPPSRAM64 bool "ESP-PSRAM64 or LY68L6400" endchoice config SPIRAM_SIZE int default -1 if SPIRAM_TYPE_AUTO default 2097152 if SPIRAM_TYPE_ESPPSRAM16 default 4194304 if SPIRAM_TYPE_ESPPSRAM32 default 8388608 if SPIRAM_TYPE_ESPPSRAM64 default 0 choice SPIRAM_SPEED prompt "Set RAM clock speed" default SPIRAM_SPEED_40M help Select the speed for the SPI RAM chip. If SPI RAM is enabled, we only support three combinations of SPI speed mode we supported now: 1. Flash SPI running at 40Mhz and RAM SPI running at 40Mhz 2. Flash SPI running at 80Mhz and RAM SPI running at 40Mhz 3. Flash SPI running at 80Mhz and RAM SPI running at 80Mhz Note: If the third mode(80Mhz+80Mhz) is enabled for SPI RAM of type 32MBit, one of the HSPI/VSPI host will be occupied by the system. Which SPI host to use can be selected by the config item SPIRAM_OCCUPY_SPI_HOST. Application code should never touch HSPI/VSPI hardware in this case. The option to select 80MHz will only be visible if the flash SPI speed is also 80MHz. (ESPTOOLPY_FLASHFREQ_80M is true) config SPIRAM_SPEED_40M bool "40MHz clock speed" config SPIRAM_SPEED_80M depends on ESPTOOLPY_FLASHFREQ_80M bool "80MHz clock speed" endchoice # insert non-chip-specific items here source "$IDF_PATH/components/esp_common/Kconfig.spiram.common" config SPIRAM_CACHE_WORKAROUND bool "Enable workaround for bug in SPI RAM cache for Rev1 ESP32s" depends on (SPIRAM_USE_MEMMAP || SPIRAM_USE_CAPS_ALLOC || SPIRAM_USE_MALLOC) && (ESP32_REV_MIN < 3) default "y" help Revision 1 of the ESP32 has a bug that can cause a write to PSRAM not to take place in some situations when the cache line needs to be fetched from external RAM and an interrupt occurs. This enables a fix in the compiler (-mfix-esp32-psram-cache-issue) that makes sure the specific code that is vulnerable to this will not be emitted. This will also not use any bits of newlib that are located in ROM, opting for a version that is compiled with the workaround and located in flash instead. The workaround is not required for ESP32 revision 3 and above. menu "SPIRAM cache workaround debugging" choice SPIRAM_CACHE_WORKAROUND_STRATEGY prompt "Workaround strategy" depends on SPIRAM_CACHE_WORKAROUND default SPIRAM_CACHE_WORKAROUND_STRATEGY_MEMW help Select the workaround strategy. Note that the strategy for precompiled libraries (libgcc, newlib, bt, wifi) is not affected by this selection. Unless you know you need a different strategy, it's suggested you stay with the default MEMW strategy. Note that DUPLDST can interfere with hardware encryption and this will be automatically disabled if this workaround is selected. 'Insert nops' is the workaround that was used in older esp-idf versions. This workaround still can cause faulty data transfers from/to SPI RAM in some situation. config SPIRAM_CACHE_WORKAROUND_STRATEGY_MEMW bool "Insert memw after vulnerable instructions (default)" config SPIRAM_CACHE_WORKAROUND_STRATEGY_DUPLDST bool "Duplicate LD/ST for 32-bit, memw for 8/16 bit" config SPIRAM_CACHE_WORKAROUND_STRATEGY_NOPS bool "Insert nops between vulnerable loads/stores (old strategy, obsolete)" endchoice #This needs to be Y only for the dupldst workaround config SPIRAM_WORKAROUND_NEED_VOLATILE_SPINLOCK bool default "y" if SPIRAM_CACHE_WORKAROUND_STRATEGY_DUPLDST endmenu config SPIRAM_BANKSWITCH_ENABLE bool "Enable bank switching for >4MiB external RAM" default y depends on SPIRAM_USE_MEMMAP || SPIRAM_USE_CAPS_ALLOC || SPIRAM_USE_MALLOC help The ESP32 only supports 4MiB of external RAM in its address space. The hardware does support larger memories, but these have to be bank-switched in and out of this address space. Enabling this allows you to reserve some MMU pages for this, which allows the use of the esp_himem api to manage these banks. #Note that this is limited to 62 banks, as esp_spiram_writeback_cache needs some kind of mapping of #some banks below that mark to work. We cannot at this moment guarantee this to exist when himem is #enabled. If spiram 2T mode is enabled, the size of 64Mbit psram will be changed as 32Mbit, so himem will be unusable. config SPIRAM_BANKSWITCH_RESERVE int "Amount of 32K pages to reserve for bank switching" depends on SPIRAM_BANKSWITCH_ENABLE default 8 range 1 62 help Select the amount of banks reserved for bank switching. Note that the amount of RAM allocatable with malloc/esp_heap_alloc_caps will decrease by 32K for each page reserved here. Note that this reservation is only actually done if your program actually uses the himem API. Without any himem calls, the reservation is not done and the original amount of memory will be available to malloc/esp_heap_alloc_caps. config SPIRAM_ALLOW_STACK_EXTERNAL_MEMORY bool "Allow external memory as an argument to xTaskCreateStatic" default n depends on SPIRAM_USE_MALLOC help Because some bits of the ESP32 code environment cannot be recompiled with the cache workaround, normally tasks cannot be safely run with their stack residing in external memory; for this reason xTaskCreate and friends always allocate stack in internal memory and xTaskCreateStatic will check if the memory passed to it is in internal memory. If you have a task that needs a large amount of stack and does not call on ROM code in any way (no direct calls, but also no Bluetooth/WiFi), you can try to disable this and use xTaskCreateStatic to create the tasks stack in external memory. choice SPIRAM_OCCUPY_SPI_HOST prompt "SPI host to use for 32MBit PSRAM" default SPIRAM_OCCUPY_VSPI_HOST depends on SPIRAM_SPEED_80M help When both flash and PSRAM is working under 80MHz, and the PSRAM is of type 32MBit, one of the HSPI/VSPI host will be used to output the clock. Select which one to use here. config SPIRAM_OCCUPY_HSPI_HOST bool "HSPI host (SPI2)" config SPIRAM_OCCUPY_VSPI_HOST bool "VSPI host (SPI3)" config SPIRAM_OCCUPY_NO_HOST bool "Will not try to use any host, will abort if not able to use the PSRAM" endchoice menu "PSRAM clock and cs IO for ESP32-DOWD" config D0WD_PSRAM_CLK_IO int "PSRAM CLK IO number" depends on ESP32_SPIRAM_SUPPORT range 0 33 default 17 help The PSRAM CLOCK IO can be any unused GPIO, user can config it based on hardware design. If user use 1.8V flash and 1.8V psram, this value can only be one of 6, 7, 8, 9, 10, 11, 16, 17. config D0WD_PSRAM_CS_IO int "PSRAM CS IO number" depends on ESP32_SPIRAM_SUPPORT range 0 33 default 16 help The PSRAM CS IO can be any unused GPIO, user can config it based on hardware design. If user use 1.8V flash and 1.8V psram, this value can only be one of 6, 7, 8, 9, 10, 11, 16, 17. endmenu menu "PSRAM clock and cs IO for ESP32-D2WD" config D2WD_PSRAM_CLK_IO int "PSRAM CLK IO number" depends on ESP32_SPIRAM_SUPPORT range 0 33 default 9 help User can config it based on hardware design. For ESP32-D2WD chip, the psram can only be 1.8V psram, so this value can only be one of 6, 7, 8, 9, 10, 11, 16, 17. config D2WD_PSRAM_CS_IO int "PSRAM CS IO number" depends on ESP32_SPIRAM_SUPPORT range 0 33 default 10 help User can config it based on hardware design. For ESP32-D2WD chip, the psram can only be 1.8V psram, so this value can only be one of 6, 7, 8, 9, 10, 11, 16, 17. endmenu menu "PSRAM clock and cs IO for ESP32-PICO" config PICO_PSRAM_CS_IO int "PSRAM CS IO number" depends on ESP32_SPIRAM_SUPPORT range 0 33 default 10 help The PSRAM CS IO can be any unused GPIO, user can config it based on hardware design. For ESP32-PICO chip, the psram share clock with flash, so user do not need to configure the clock IO. For the reference hardware design, please refer to https://www.espressif.com/sites/default/files/documentation/esp32-pico-d4_datasheet_en.pdf endmenu config SPIRAM_CUSTOM_SPIWP_SD3_PIN bool "Use custom SPI PSRAM WP(SD3) Pin when flash pins set in eFuse (read help)" depends on IDF_TARGET_ESP32 && (ESPTOOLPY_FLASHMODE_DIO || ESPTOOLPY_FLASHMODE_DOUT) default y if SPIRAM_SPIWP_SD3_PIN != 7 # backwards compatibility, can remove in IDF 5 default n help This setting is only used if the SPI flash pins have been overridden by setting the eFuses SPI_PAD_CONFIG_xxx, and the SPI flash mode is DIO or DOUT. When this is the case, the eFuse config only defines 3 of the 4 Quad I/O data pins. The WP pin (aka ESP32 pin "SD_DATA_3" or SPI flash pin "IO2") is not specified in eFuse. The psram only has QPI mode, so a WP pin setting is necessary. If this config item is set to N (default), the correct WP pin will be automatically used for any Espressif chip or module with integrated flash. If a custom setting is needed, set this config item to Y and specify the GPIO number connected to the WP pin. When flash mode is set to QIO or QOUT, the PSRAM WP pin will be set the same as the SPI Flash WP pin configured in the bootloader. config SPIRAM_SPIWP_SD3_PIN int "Custom SPI PSRAM WP(SD3) Pin" depends on IDF_TARGET_ESP32 && (ESPTOOLPY_FLASHMODE_DIO || ESPTOOLPY_FLASHMODE_DOUT) #depends on SPIRAM_CUSTOM_SPIWP_SD3_PIN # backwards compatibility, can uncomment in IDF 5 range 0 33 default 7 help The option "Use custom SPI PSRAM WP(SD3) pin" must be set or this value is ignored If burning a customized set of SPI flash pins in eFuse and using DIO or DOUT mode for flash, set this value to the GPIO number of the SPIRAM WP pin. config SPIRAM_2T_MODE bool "Enable SPI PSRAM 2T mode" depends on ESP32_SPIRAM_SUPPORT default "n" help Enable this option to fix single bit errors inside 64Mbit PSRAM. Some 64Mbit PSRAM chips have a hardware issue in the RAM which causes bit errors at multiple fixed bit positions. Note: If this option is enabled, the 64Mbit PSRAM chip will appear to be 32Mbit in size. Applications will not be affected unless the use the esp_himem APIs, which are not supported in 2T mode. endmenu # "SPI RAM config" config ESP32_MEMMAP_TRACEMEM bool default "n" config ESP32_MEMMAP_TRACEMEM_TWOBANKS bool default "n" config ESP32_TRAX bool "Use TRAX tracing feature" default "n" select ESP32_MEMMAP_TRACEMEM help The ESP32 contains a feature which allows you to trace the execution path the processor has taken through the program. This is stored in a chunk of 32K (16K for single-processor) of memory that can't be used for general purposes anymore. Disable this if you do not know what this is. config ESP32_TRAX_TWOBANKS bool "Reserve memory for tracing both pro as well as app cpu execution" default "n" depends on ESP32_TRAX && !FREERTOS_UNICORE select ESP32_MEMMAP_TRACEMEM_TWOBANKS help The ESP32 contains a feature which allows you to trace the execution path the processor has taken through the program. This is stored in a chunk of 32K (16K for single-processor) of memory that can't be used for general purposes anymore. Disable this if you do not know what this is. # Memory to reverse for trace, used in linker script config ESP32_TRACEMEM_RESERVE_DRAM hex default 0x8000 if ESP32_MEMMAP_TRACEMEM && ESP32_MEMMAP_TRACEMEM_TWOBANKS default 0x4000 if ESP32_MEMMAP_TRACEMEM && !ESP32_MEMMAP_TRACEMEM_TWOBANKS default 0x0 choice ESP32_UNIVERSAL_MAC_ADDRESSES bool "Number of universally administered (by IEEE) MAC address" default ESP32_UNIVERSAL_MAC_ADDRESSES_FOUR help Configure the number of universally administered (by IEEE) MAC addresses. During initialization, MAC addresses for each network interface are generated or derived from a single base MAC address. If the number of universal MAC addresses is four, all four interfaces (WiFi station, WiFi softap, Bluetooth and Ethernet) receive a universally administered MAC address. These are generated sequentially by adding 0, 1, 2 and 3 (respectively) to the final octet of the base MAC address. If the number of universal MAC addresses is two, only two interfaces (WiFi station and Bluetooth) receive a universally administered MAC address. These are generated sequentially by adding 0 and 1 (respectively) to the base MAC address. The remaining two interfaces (WiFi softap and Ethernet) receive local MAC addresses. These are derived from the universal WiFi station and Bluetooth MAC addresses, respectively. When using the default (Espressif-assigned) base MAC address, either setting can be used. When using a custom universal MAC address range, the correct setting will depend on the allocation of MAC addresses in this range (either 2 or 4 per device.) config ESP32_UNIVERSAL_MAC_ADDRESSES_TWO bool "Two" select ESP_MAC_ADDR_UNIVERSE_WIFI_STA select ESP_MAC_ADDR_UNIVERSE_BT config ESP32_UNIVERSAL_MAC_ADDRESSES_FOUR bool "Four" select ESP_MAC_ADDR_UNIVERSE_WIFI_STA select ESP_MAC_ADDR_UNIVERSE_WIFI_AP select ESP_MAC_ADDR_UNIVERSE_BT select ESP_MAC_ADDR_UNIVERSE_ETH endchoice config ESP32_UNIVERSAL_MAC_ADDRESSES int default 2 if ESP32_UNIVERSAL_MAC_ADDRESSES_TWO default 4 if ESP32_UNIVERSAL_MAC_ADDRESSES_FOUR config ESP32_ULP_COPROC_ENABLED bool "Enable Ultra Low Power (ULP) Coprocessor" default "n" help Set to 'y' if you plan to load a firmware for the coprocessor. If this option is enabled, further coprocessor configuration will appear in the Components menu. config ESP32_ULP_COPROC_RESERVE_MEM int prompt "RTC slow memory reserved for coprocessor" if ESP32_ULP_COPROC_ENABLED default 512 if ESP32_ULP_COPROC_ENABLED range 32 8192 if ESP32_ULP_COPROC_ENABLED default 0 if !ESP32_ULP_COPROC_ENABLED range 0 0 if !ESP32_ULP_COPROC_ENABLED help Bytes of memory to reserve for ULP coprocessor firmware & data. Data is reserved at the beginning of RTC slow memory. config ESP32_DEBUG_OCDAWARE bool "Make exception and panic handlers JTAG/OCD aware" default y select FREERTOS_DEBUG_OCDAWARE help The FreeRTOS panic and unhandled exception handers can detect a JTAG OCD debugger and instead of panicking, have the debugger stop on the offending instruction. config ESP32_BROWNOUT_DET bool "Hardware brownout detect & reset" default y help The ESP32 has a built-in brownout detector which can detect if the voltage is lower than a specific value. If this happens, it will reset the chip in order to prevent unintended behaviour. choice ESP32_BROWNOUT_DET_LVL_SEL prompt "Brownout voltage level" depends on ESP32_BROWNOUT_DET default ESP32_BROWNOUT_DET_LVL_SEL_0 help The brownout detector will reset the chip when the supply voltage is approximately below this level. Note that there may be some variation of brownout voltage level between each ESP32 chip. #The voltage levels here are estimates, more work needs to be done to figure out the exact voltages #of the brownout threshold levels. config ESP32_BROWNOUT_DET_LVL_SEL_0 bool "2.43V +/- 0.05" config ESP32_BROWNOUT_DET_LVL_SEL_1 bool "2.48V +/- 0.05" config ESP32_BROWNOUT_DET_LVL_SEL_2 bool "2.58V +/- 0.05" config ESP32_BROWNOUT_DET_LVL_SEL_3 bool "2.62V +/- 0.05" config ESP32_BROWNOUT_DET_LVL_SEL_4 bool "2.67V +/- 0.05" config ESP32_BROWNOUT_DET_LVL_SEL_5 bool "2.70V +/- 0.05" config ESP32_BROWNOUT_DET_LVL_SEL_6 bool "2.77V +/- 0.05" config ESP32_BROWNOUT_DET_LVL_SEL_7 bool "2.80V +/- 0.05" endchoice config ESP32_BROWNOUT_DET_LVL int default 0 if ESP32_BROWNOUT_DET_LVL_SEL_0 default 1 if ESP32_BROWNOUT_DET_LVL_SEL_1 default 2 if ESP32_BROWNOUT_DET_LVL_SEL_2 default 3 if ESP32_BROWNOUT_DET_LVL_SEL_3 default 4 if ESP32_BROWNOUT_DET_LVL_SEL_4 default 5 if ESP32_BROWNOUT_DET_LVL_SEL_5 default 6 if ESP32_BROWNOUT_DET_LVL_SEL_6 default 7 if ESP32_BROWNOUT_DET_LVL_SEL_7 #Reduce PHY TX power when brownout reset config ESP32_REDUCE_PHY_TX_POWER bool "Reduce PHY TX power when brownout reset" depends on ESP32_BROWNOUT_DET default y help When brownout reset occurs, reduce PHY TX power to keep the code running # Note about the use of "FRC1" name: currently FRC1 timer is not used for # high resolution timekeeping anymore. Instead the esp_timer API is used. # FRC1 name in the option name is kept for compatibility. choice ESP32_TIME_SYSCALL prompt "Timers used for gettimeofday function" default ESP32_TIME_SYSCALL_USE_RTC_FRC1 help This setting defines which hardware timers are used to implement 'gettimeofday' and 'time' functions in C library. - If both high-resolution and RTC timers are used, timekeeping will continue in deep sleep. Time will be reported at 1 microsecond resolution. This is the default, and the recommended option. - If only high-resolution timer is used, gettimeofday will provide time at microsecond resolution. Time will not be preserved when going into deep sleep mode. - If only RTC timer is used, timekeeping will continue in deep sleep, but time will be measured at 6.(6) microsecond resolution. Also the gettimeofday function itself may take longer to run. - If no timers are used, gettimeofday and time functions return -1 and set errno to ENOSYS. - When RTC is used for timekeeping, two RTC_STORE registers are used to keep time in deep sleep mode. config ESP32_TIME_SYSCALL_USE_RTC_FRC1 bool "RTC and high-resolution timer" select ESP_TIME_FUNCS_USE_RTC_TIMER select ESP_TIME_FUNCS_USE_ESP_TIMER config ESP32_TIME_SYSCALL_USE_RTC bool "RTC" select ESP_TIME_FUNCS_USE_RTC_TIMER config ESP32_TIME_SYSCALL_USE_FRC1 bool "High-resolution timer" select ESP_TIME_FUNCS_USE_ESP_TIMER config ESP32_TIME_SYSCALL_USE_NONE bool "None" select ESP_TIME_FUNCS_USE_NONE endchoice choice ESP32_RTC_CLK_SRC prompt "RTC clock source" default ESP32_RTC_CLK_SRC_INT_RC help Choose which clock is used as RTC clock source. - "Internal 150kHz oscillator" option provides lowest deep sleep current consumption, and does not require extra external components. However frequency stability with respect to temperature is poor, so time may drift in deep/light sleep modes. - "External 32kHz crystal" provides better frequency stability, at the expense of slightly higher (1uA) deep sleep current consumption. - "External 32kHz oscillator" allows using 32kHz clock generated by an external circuit. In this case, external clock signal must be connected to 32K_XN pin. Amplitude should be <1.2V in case of sine wave signal, and <1V in case of square wave signal. Common mode voltage should be 0.1 < Vcm < 0.5Vamp, where Vamp is the signal amplitude. Additionally, 1nF capacitor must be connected between 32K_XP pin and ground. 32K_XP pin can not be used as a GPIO in this case. - "Internal 8.5MHz oscillator divided by 256" option results in higher deep sleep current (by 5uA) but has better frequency stability than the internal 150kHz oscillator. It does not require external components. config ESP32_RTC_CLK_SRC_INT_RC bool "Internal 150kHz RC oscillator" config ESP32_RTC_CLK_SRC_EXT_CRYS bool "External 32kHz crystal" select ESP_SYSTEM_RTC_EXT_XTAL config ESP32_RTC_CLK_SRC_EXT_OSC bool "External 32kHz oscillator at 32K_XN pin" config ESP32_RTC_CLK_SRC_INT_8MD256 bool "Internal 8.5MHz oscillator, divided by 256 (~33kHz)" endchoice choice ESP32_RTC_EXT_CRYST_ADDIT_CURRENT_METHOD prompt "Additional current for external 32kHz crystal" depends on ESP32_RTC_CLK_SRC_EXT_CRYS depends on ESP32_REV_MIN <= 1 default ESP32_RTC_EXT_CRYST_ADDIT_CURRENT_NONE help With some 32kHz crystal configurations, the X32N and X32P pins may not have enough drive strength to keep the crystal oscillating. Choose the method to provide additional current from touchpad 9 to the external 32kHz crystal. Note that the deep sleep current is slightly high (4-5uA) and the touchpad and the wakeup sources of both touchpad and ULP are not available in method 1 and method 2. This problem is fixed in ESP32 ECO 3, so this workaround is not needed. Setting the project configuration to minimum revision ECO3 will disable this option, , allow all wakeup sources, and save some code size. - "None" option will not provide additional current to external crystal - "Method 1" option can't ensure 100% to solve the external 32k crystal start failed issue, but the touchpad can work in this method. - "Method 2" option can solve the external 32k issue, but the touchpad can't work in this method. config ESP32_RTC_EXT_CRYST_ADDIT_CURRENT_NONE bool "None" config ESP32_RTC_EXT_CRYST_ADDIT_CURRENT bool "Method 1" config ESP32_RTC_EXT_CRYST_ADDIT_CURRENT_V2 bool "Method 2" endchoice config ESP32_RTC_CLK_CAL_CYCLES int "Number of cycles for RTC_SLOW_CLK calibration" default 3000 if ESP32_RTC_CLK_SRC_EXT_CRYS || ESP32_RTC_CLK_SRC_EXT_OSC || ESP32_RTC_CLK_SRC_INT_8MD256 default 1024 if ESP32_RTC_CLK_SRC_INT_RC range 0 27000 if ESP32_RTC_CLK_SRC_EXT_CRYS || ESP32_RTC_CLK_SRC_EXT_OSC || ESP32_RTC_CLK_SRC_INT_8MD256 range 0 32766 if ESP32_RTC_CLK_SRC_INT_RC help When the startup code initializes RTC_SLOW_CLK, it can perform calibration by comparing the RTC_SLOW_CLK frequency with main XTAL frequency. This option sets the number of RTC_SLOW_CLK cycles measured by the calibration routine. Higher numbers increase calibration precision, which may be important for applications which spend a lot of time in deep sleep. Lower numbers reduce startup time. When this option is set to 0, clock calibration will not be performed at startup, and approximate clock frequencies will be assumed: - 150000 Hz if internal RC oscillator is used as clock source. For this use value 1024. - 32768 Hz if the 32k crystal oscillator is used. For this use value 3000 or more. In case more value will help improve the definition of the launch of the crystal. If the crystal could not start, it will be switched to internal RC. config ESP32_RTC_XTAL_CAL_RETRY int "Number of attempts to repeat 32k XTAL calibration" default 1 depends on ESP32_RTC_CLK_SRC_EXT_CRYS help Number of attempts to repeat 32k XTAL calibration before giving up and switching to the internal RC. Increase this option if the 32k crystal oscillator does not start and switches to internal RC. config ESP32_DEEP_SLEEP_WAKEUP_DELAY int "Extra delay in deep sleep wake stub (in us)" default 2000 range 0 5000 help When ESP32 exits deep sleep, the CPU and the flash chip are powered on at the same time. CPU will run deep sleep stub first, and then proceed to load code from flash. Some flash chips need sufficient time to pass between power on and first read operation. By default, without any extra delay, this time is approximately 900us, although some flash chip types need more than that. By default extra delay is set to 2000us. When optimizing startup time for applications which require it, this value may be reduced. If you are seeing "flash read err, 1000" message printed to the console after deep sleep reset, try increasing this value. choice ESP32_XTAL_FREQ_SEL prompt "Main XTAL frequency" default ESP32_XTAL_FREQ_40 help ESP32 currently supports the following XTAL frequencies: - 26 MHz - 40 MHz Startup code can automatically estimate XTAL frequency. This feature uses the internal 8MHz oscillator as a reference. Because the internal oscillator frequency is temperature dependent, it is not recommended to use automatic XTAL frequency detection in applications which need to work at high ambient temperatures and use high-temperature qualified chips and modules. config ESP32_XTAL_FREQ_40 bool "40 MHz" config ESP32_XTAL_FREQ_26 bool "26 MHz" config ESP32_XTAL_FREQ_AUTO bool "Autodetect" endchoice # Keep these values in sync with rtc_xtal_freq_t enum in soc/rtc.h config ESP32_XTAL_FREQ int default 0 if ESP32_XTAL_FREQ_AUTO default 40 if ESP32_XTAL_FREQ_40 default 26 if ESP32_XTAL_FREQ_26 config ESP32_DISABLE_BASIC_ROM_CONSOLE bool "Permanently disable BASIC ROM Console" default n help If set, the first time the app boots it will disable the BASIC ROM Console permanently (by burning an eFuse). Otherwise, the BASIC ROM Console starts on reset if no valid bootloader is read from the flash. (Enabling secure boot also disables the BASIC ROM Console by default.) config ESP32_NO_BLOBS bool "No Binary Blobs" depends on !BT_ENABLED default n help If enabled, this disables the linking of binary libraries in the application build. Note that after enabling this Wi-Fi/Bluetooth will not work. config ESP32_COMPATIBLE_PRE_V2_1_BOOTLOADERS bool "App compatible with bootloaders before IDF v2.1" default n help Bootloaders before IDF v2.1 did less initialisation of the system clock. This setting needs to be enabled to build an app which can be booted by these older bootloaders. If this setting is enabled, the app can be booted by any bootloader from IDF v1.0 up to the current version. If this setting is disabled, the app can only be booted by bootloaders from IDF v2.1 or newer. Enabling this setting adds approximately 1KB to the app's IRAM usage. config ESP32_APP_INIT_CLK bool default y if ESP32_COMPATIBLE_PRE_V2_1_BOOTLOADERS default y if APP_BUILD_TYPE_ELF_RAM config ESP32_RTCDATA_IN_FAST_MEM bool "Place RTC_DATA_ATTR and RTC_RODATA_ATTR variables into RTC fast memory segment" default n depends on FREERTOS_UNICORE help This option allows to place .rtc_data and .rtc_rodata sections into RTC fast memory segment to free the slow memory region for ULP programs. This option depends on the CONFIG_FREERTOS_UNICORE option because RTC fast memory can be accessed only by PRO_CPU core. config ESP32_USE_FIXED_STATIC_RAM_SIZE bool "Use fixed static RAM size" default n help If this option is disabled, the DRAM part of the heap starts right after the .bss section, within the dram0_0 region. As a result, adding or removing some static variables will change the available heap size. If this option is enabled, the DRAM part of the heap starts right after the dram0_0 region, where its length is set with ESP32_FIXED_STATIC_RAM_SIZE config ESP32_FIXED_STATIC_RAM_SIZE hex "Fixed Static RAM size" default 0x1E000 range 0 0x2c200 depends on ESP32_USE_FIXED_STATIC_RAM_SIZE help RAM size dedicated for static variables (.data & .bss sections). Please note that the actual length will be reduced by BT_RESERVE_DRAM if Bluetooth controller is enabled. config ESP32_DPORT_DIS_INTERRUPT_LVL int "Disable the interrupt level for the DPORT workarounds" default 5 help To prevent interrupting DPORT workarounds, need to disable interrupt with a maximum used level in the system. config ESP32_IRAM_AS_8BIT_ACCESSIBLE_MEMORY bool "Enable IRAM as 8 bit accessible memory" depends on FREERTOS_UNICORE help If enabled, application can use IRAM as byte accessible region for storing data (Note: IRAM region cannot be used as task stack) This is possible due to handling of exceptions `LoadStoreError (3)` and `LoadStoreAlignmentError (9)` Each unaligned read/write access will incur a penalty of maximum of 167 CPU cycles. config ESP32_ALLOW_RTC_FAST_MEM_AS_HEAP bool "Enable RTC fast memory for dynamic allocations" default y depends on FREERTOS_UNICORE help This config option allows to add RTC fast memory region to system heap with capability similar to that of DRAM region but without DMA. This memory will be consumed first per heap initialization order by early startup services and scheduler related code. Speed wise RTC fast memory operates on APB clock and hence does not have much performance impact. RTC fast memory is accessible to PRO cpu only and hence this is allowed for single core configuration only for ESP32. endmenu # ESP32-Specific