menu "SPI Flash driver" config SPI_FLASH_VERIFY_WRITE bool "Verify SPI flash writes" default n help If this option is enabled, any time SPI flash is written then the data will be read back and verified. This can catch hardware problems with SPI flash, or flash which was not erased before verification. config SPI_FLASH_LOG_FAILED_WRITE bool "Log errors if verification fails" depends on SPI_FLASH_VERIFY_WRITE default n help If this option is enabled, if SPI flash write verification fails then a log error line will be written with the address, expected & actual values. This can be useful when debugging hardware SPI flash problems. config SPI_FLASH_WARN_SETTING_ZERO_TO_ONE bool "Log warning if writing zero bits to ones" depends on SPI_FLASH_VERIFY_WRITE default n help If this option is enabled, any SPI flash write which tries to set zero bits in the flash to ones will log a warning. Such writes will not result in the requested data appearing identically in flash once written, as SPI NOR flash can only set bits to one when an entire sector is erased. After erasing, individual bits can only be written from one to zero. Note that some software (such as SPIFFS) which is aware of SPI NOR flash may write one bits as an optimisation, relying on the data in flash becoming a bitwise AND of the new data and any existing data. Such software will log spurious warnings if this option is enabled. config SPI_FLASH_ENABLE_COUNTERS bool "Enable operation counters" default 0 help This option enables the following APIs: - spi_flash_reset_counters - spi_flash_dump_counters - spi_flash_get_counters These APIs may be used to collect performance data for spi_flash APIs and to help understand behaviour of libraries which use SPI flash. config SPI_FLASH_ROM_DRIVER_PATCH bool "Enable SPI flash ROM driver patched functions" default y help Enable this flag to use patched versions of SPI flash ROM driver functions. This option should be enabled, if any one of the following is true: (1) need to write to flash on ESP32-D2WD; (2) main SPI flash is connected to non-default pins; (3) main SPI flash chip is manufactured by ISSI. config SPI_FLASH_ROM_IMPL bool "Use esp_flash implementation in ROM" depends on IDF_TARGET_ESP32S3 || IDF_TARGET_ESP32C3 default n help Enable this flag to use new SPI flash driver functions from ROM instead of ESP-IDF. If keeping this as "n" in your project, you will have less free IRAM. But you can use all of our flash features. If making this as "y" in your project, you will increase free IRAM. But you may miss out on some flash features and support for new flash chips. choice SPI_FLASH_DANGEROUS_WRITE bool "Writing to dangerous flash regions" default SPI_FLASH_DANGEROUS_WRITE_ABORTS help SPI flash APIs can optionally abort or return a failure code if erasing or writing addresses that fall at the beginning of flash (covering the bootloader and partition table) or that overlap the app partition that contains the running app. It is not recommended to ever write to these regions from an IDF app, and this check prevents logic errors or corrupted firmware memory from damaging these regions. Note that this feature *does not* check calls to the esp_rom_xxx SPI flash ROM functions. These functions should not be called directly from IDF applications. config SPI_FLASH_DANGEROUS_WRITE_ABORTS bool "Aborts" config SPI_FLASH_DANGEROUS_WRITE_FAILS bool "Fails" config SPI_FLASH_DANGEROUS_WRITE_ALLOWED bool "Allowed" endchoice config SPI_FLASH_USE_LEGACY_IMPL bool "Use the legacy implementation before IDF v4.0" default n help The implementation of SPI flash has been greatly changed in IDF v4.0. Enable this option to use the legacy implementation. config SPI_FLASH_SHARE_SPI1_BUS bool "Support other devices attached to SPI1 bus" default n # The bus lock on SPI1 is meaningless when the legacy implementation is used, or the SPI # driver does not support SPI1. depends on !SPI_FLASH_USE_LEGACY_IMPL && !IDF_TARGET_ESP32S2 help Each SPI bus needs a lock for arbitration among devices. This allows multiple devices on a same bus, but may reduce the speed of esp_flash driver access to the main flash chip. If you only need to use esp_flash driver to access the main flash chip, disable this option, and the lock will be bypassed on SPI1 bus. Otherwise if extra devices are needed to attach to SPI1 bus, enable this option. config SPI_FLASH_BYPASS_BLOCK_ERASE bool "Bypass a block erase and always do sector erase" default n help Some flash chips can have very high "max" erase times, especially for block erase (32KB or 64KB). This option allows to bypass "block erase" and always do sector erase commands. This will be much slower overall in most cases, but improves latency for other code to run. config SPI_FLASH_YIELD_DURING_ERASE bool "Enables yield operation during flash erase" default y help This allows to yield the CPUs between erase commands. Prevents starvation of other tasks. config SPI_FLASH_ERASE_YIELD_DURATION_MS int "Duration of erasing to yield CPUs (ms)" depends on SPI_FLASH_YIELD_DURING_ERASE default 20 help If a duration of one erase command is large then it will yield CPUs after finishing a current command. config SPI_FLASH_ERASE_YIELD_TICKS int "CPU release time (tick) for an erase operation" depends on SPI_FLASH_YIELD_DURING_ERASE default 1 help Defines how many ticks will be before returning to continue a erasing. config SPI_FLASH_AUTO_SUSPEND bool "Auto suspend long erase/write operations" default n depends on IDF_TARGET_ESP32C3 && !SPI_FLASH_USE_LEGACY_IMPL && !SPI_FLASH_ROM_IMPL help This is made default n, because this needs bootloader support. This feature needs special bootloader support. If you want to OTA to a image with this feature (e.g. turn on this config option for OTA image), please make sure the bootloader has the support for it. (above IDF v4.3) config SPI_FLASH_WRITE_CHUNK_SIZE int "Flash write chunk size" default 8192 range 256 8192 help Flash write is broken down in terms of multiple (smaller) write operations. This configuration options helps to set individual write chunk size, smaller value here ensures that cache (and non-IRAM resident interrupts) remains disabled for shorter duration. config SPI_FLASH_SIZE_OVERRIDE bool "Override flash size in bootloader header by ESPTOOLPY_FLASHSIZE" default n help SPI Flash driver uses the flash size configured in bootloader header by default. Enable this option to override flash size with latest ESPTOOLPY_FLASHSIZE value from the app header if the size in the bootloader header is incorrect. config SPI_FLASH_CHECK_ERASE_TIMEOUT_DISABLED bool "Flash timeout checkout disabled" depends on !SPI_FLASH_USE_LEGACY_IMPL default n help This option is helpful if you are using a flash chip whose timeout is quite large or unpredictable. menu "Auto-detect flash chips" config SPI_FLASH_SUPPORT_ISSI_CHIP bool "ISSI" default y help Enable this to support auto detection of ISSI chips if chip vendor not directly given by ``chip_drv`` member of the chip struct. This adds support for variant chips, however will extend detecting time. config SPI_FLASH_SUPPORT_MXIC_CHIP bool "MXIC" default y help Enable this to support auto detection of MXIC chips if chip vendor not directly given by ``chip_drv`` member of the chip struct. This adds support for variant chips, however will extend detecting time. config SPI_FLASH_SUPPORT_GD_CHIP bool "GigaDevice" default y help Enable this to support auto detection of GD (GigaDevice) chips if chip vendor not directly given by ``chip_drv`` member of the chip struct. If you are using Wrover modules, please don't disable this, otherwise your flash may not work in 4-bit mode. This adds support for variant chips, however will extend detecting time and image size. Note that the default chip driver supports the GD chips with product ID 60H. config SPI_FLASH_SUPPORT_WINBOND_CHIP bool "Winbond" default y help Enable this to support auto detection of Winbond chips if chip vendor not directly given by ``chip_drv`` member of the chip struct. This adds support for variant chips, however will extend detecting time. config SPI_FLASH_SUPPORT_BOYA_CHIP bool "BOYA" depends on !IDF_TARGET_ESP32 default y help Enable this to support auto detection of BOYA chips if chip vendor not directly given by ``chip_drv`` member of the chip struct. This adds support for variant chips, however will extend detecting time. endmenu #auto detect flash chips endmenu