choice BTDM_CTRL_MODE prompt "Bluetooth controller mode (BR/EDR/BLE/DUALMODE)" help Specify the bluetooth controller mode (BR/EDR, BLE or dual mode). config BTDM_CTRL_MODE_BLE_ONLY bool "BLE Only" config BTDM_CTRL_MODE_BR_EDR_ONLY bool "BR/EDR Only" config BTDM_CTRL_MODE_BTDM bool "Bluetooth Dual Mode" endchoice config BTDM_CTRL_BLE_MAX_CONN int "BLE Max Connections" depends on BTDM_CTRL_MODE_BLE_ONLY || BTDM_CTRL_MODE_BTDM default 3 range 1 9 help BLE maximum connections of bluetooth controller. Each connection uses 1KB static DRAM whenever the BT controller is enabled. config BTDM_CTRL_BR_EDR_MAX_ACL_CONN int "BR/EDR ACL Max Connections" depends on BTDM_CTRL_MODE_BR_EDR_ONLY || BTDM_CTRL_MODE_BTDM default 2 range 1 7 help BR/EDR ACL maximum connections of bluetooth controller. Each connection uses 1.2 KB DRAM whenever the BT controller is enabled. config BTDM_CTRL_BR_EDR_MAX_SYNC_CONN int "BR/EDR Sync(SCO/eSCO) Max Connections" depends on BTDM_CTRL_MODE_BR_EDR_ONLY || BTDM_CTRL_MODE_BTDM default 0 range 0 3 help BR/EDR Synchronize maximum connections of bluetooth controller. Each connection uses 2 KB DRAM whenever the BT controller is enabled. choice BTDM_CTRL_BR_EDR_SCO_DATA_PATH prompt "BR/EDR Sync(SCO/eSCO) default data path" depends on BTDM_CTRL_MODE_BR_EDR_ONLY || BTDM_CTRL_MODE_BTDM default BTDM_CTRL_BR_EDR_SCO_DATA_PATH_PCM help SCO data path, i.e. HCI or PCM. SCO data can be sent/received through HCI synchronous packets, or the data can be routed to on-chip PCM module on ESP32. PCM input/output signals can be "matrixed" to GPIOs. The default data path can also be set using API "esp_bredr_sco_datapath_set" config BTDM_CTRL_BR_EDR_SCO_DATA_PATH_HCI bool "HCI" config BTDM_CTRL_BR_EDR_SCO_DATA_PATH_PCM bool "PCM" endchoice config BTDM_CTRL_BR_EDR_SCO_DATA_PATH_EFF int default 0 if BTDM_CTRL_BR_EDR_SCO_DATA_PATH_HCI default 1 if BTDM_CTRL_BR_EDR_SCO_DATA_PATH_PCM default 0 menuconfig BTDM_CTRL_PCM_ROLE_EDGE_CONFIG bool "PCM Signal Config (Role and Polar)" depends on BTDM_CTRL_BR_EDR_SCO_DATA_PATH_PCM default y choice BTDM_CTRL_PCM_ROLE prompt "PCM Role" depends on BTDM_CTRL_PCM_ROLE_EDGE_CONFIG help PCM role can be configured as PCM master or PCM slave config BTDM_CTRL_PCM_ROLE_MASTER bool "PCM Master" config BTDM_CTRL_PCM_ROLE_SLAVE bool "PCM Slave" endchoice choice BTDM_CTRL_PCM_POLAR prompt "PCM Polar" depends on BTDM_CTRL_PCM_ROLE_EDGE_CONFIG help PCM polarity can be configured as Falling Edge or Rising Edge config BTDM_CTRL_PCM_POLAR_FALLING_EDGE bool "Falling Edge" config BTDM_CTRL_PCM_POLAR_RISING_EDGE bool "Rising Edge" endchoice config BTDM_CTRL_PCM_ROLE_EFF int default 0 if BTDM_CTRL_PCM_ROLE_MASTER default 1 if BTDM_CTRL_PCM_ROLE_SLAVE default 0 config BTDM_CTRL_PCM_POLAR_EFF int default 0 if BTDM_CTRL_PCM_POLAR_FALLING_EDGE default 1 if BTDM_CTRL_PCM_POLAR_RISING_EDGE default 0 config BTDM_CTRL_AUTO_LATENCY bool "Auto latency" depends on BTDM_CTRL_MODE_BTDM default n help BLE auto latency, used to enhance classic BT performance while classic BT and BLE are enabled at the same time. config BTDM_CTRL_AUTO_LATENCY_EFF bool default BTDM_CTRL_AUTO_LATENCY if BTDM_CTRL_MODE_BTDM default n config BTDM_CTRL_LEGACY_AUTH_VENDOR_EVT bool "Legacy Authentication Vendor Specific Event Enable" depends on BTDM_CTRL_MODE_BR_EDR_ONLY || BTDM_CTRL_MODE_BTDM default y help To protect from BIAS attack during Legacy authentication, Legacy authentication Vendor specific event should be enabled config BTDM_CTRL_LEGACY_AUTH_VENDOR_EVT_EFF bool default BTDM_CTRL_LEGACY_AUTH_VENDOR_EVT if BTDM_CTRL_MODE_BR_EDR_ONLY || BTDM_CTRL_MODE_BTDM default 0 config BTDM_CTRL_BLE_MAX_CONN_EFF int default BTDM_CTRL_BLE_MAX_CONN if BTDM_CTRL_MODE_BLE_ONLY || BTDM_CTRL_MODE_BTDM default 0 config BTDM_CTRL_BR_EDR_MAX_ACL_CONN_EFF int default BTDM_CTRL_BR_EDR_MAX_ACL_CONN if BTDM_CTRL_MODE_BR_EDR_ONLY || BTDM_CTRL_MODE_BTDM default 0 config BTDM_CTRL_BR_EDR_MAX_SYNC_CONN_EFF int default BTDM_CTRL_BR_EDR_MAX_SYNC_CONN if BTDM_CTRL_MODE_BR_EDR_ONLY || BTDM_CTRL_MODE_BTDM default 0 choice BTDM_CTRL_PINNED_TO_CORE_CHOICE prompt "The cpu core which bluetooth controller run" depends on !FREERTOS_UNICORE help Specify the cpu core to run bluetooth controller. Can not specify no-affinity. config BTDM_CTRL_PINNED_TO_CORE_0 bool "Core 0 (PRO CPU)" config BTDM_CTRL_PINNED_TO_CORE_1 bool "Core 1 (APP CPU)" depends on !FREERTOS_UNICORE endchoice config BTDM_CTRL_PINNED_TO_CORE int default 0 if BTDM_CTRL_PINNED_TO_CORE_0 default 1 if BTDM_CTRL_PINNED_TO_CORE_1 default 0 choice BTDM_CTRL_HCI_MODE_CHOICE prompt "HCI mode" help Speicify HCI mode as VHCI or UART(H4) config BTDM_CTRL_HCI_MODE_VHCI bool "VHCI" help Normal option. Mostly, choose this VHCI when bluetooth host run on ESP32, too. config BTDM_CTRL_HCI_MODE_UART_H4 bool "UART(H4)" help If use external bluetooth host which run on other hardware and use UART as the HCI interface, choose this option. endchoice menu "HCI UART(H4) Options" visible if BTDM_CTRL_HCI_MODE_UART_H4 config BTDM_CTRL_HCI_UART_NO int "UART Number for HCI" depends on BTDM_CTRL_HCI_MODE_UART_H4 range 1 2 default 1 help Uart number for HCI. The available uart is UART1 and UART2. config BTDM_CTRL_HCI_UART_BAUDRATE int "UART Baudrate for HCI" depends on BTDM_CTRL_HCI_MODE_UART_H4 range 115200 921600 default 921600 help UART Baudrate for HCI. Please use standard baudrate. endmenu menu "MODEM SLEEP Options" config BTDM_CTRL_MODEM_SLEEP bool "Bluetooth modem sleep" default y help Enable/disable bluetooth controller low power mode. choice BTDM_CTRL_MODEM_SLEEP_MODE prompt "Bluetooth Modem sleep mode" depends on BTDM_CTRL_MODEM_SLEEP help To select which strategy to use for modem sleep config BTDM_CTRL_MODEM_SLEEP_MODE_ORIG bool "ORIG Mode(sleep with low power clock)" help ORIG mode is a bluetooth sleep mode that can be used for dual mode controller. In this mode, bluetooth controller sleeps between BR/EDR frames and BLE events. A low power clock is used to maintain bluetooth reference clock. config BTDM_CTRL_MODEM_SLEEP_MODE_EVED bool "EVED Mode(For internal test only)" help EVED mode is for BLE only and is only for internal test. Do not use it for production. this mode is not compatible with DFS nor light sleep endchoice choice BTDM_CTRL_LOW_POWER_CLOCK prompt "Bluetooth low power clock" depends on BTDM_CTRL_MODEM_SLEEP_MODE_ORIG help Select the low power clock source for bluetooth controller. Bluetooth low power clock is the clock source to maintain time in sleep mode. - "Main crystal" option provides good accuracy and can support Dynamic Frequency Scaling to be used with Bluetooth modem sleep. Light sleep is not supported. - "External 32kHz crystal" option allows user to use a 32.768kHz crystal as Bluetooth low power clock. This option is allowed as long as External 32kHz crystal is configured as the system RTC clock source. This option provides good accuracy and supports Bluetooth modem sleep to be used alongside Dynamic Frequency Scaling or light sleep. config BTDM_CTRL_LPCLK_SEL_MAIN_XTAL bool "Main crystal" help Main crystal can be used as low power clock for bluetooth modem sleep. If this option is selected, bluetooth modem sleep can work under Dynamic Frequency Scaling(DFS) enabled, but cannot work when light sleep is enabled. Main crystal has a good performance in accuracy as the bluetooth low power clock source. config BTDM_CTRL_LPCLK_SEL_EXT_32K_XTAL bool "External 32kHz crystal" depends on ESP32_RTC_CLK_SRC_EXT_CRYS help External 32kHz crystal has a nominal frequency of 32.768kHz and provides good frequency stability. If used as Bluetooth low power clock, External 32kHz can support Bluetooth modem sleep to be used with both DFS and light sleep. endchoice endmenu choice BTDM_BLE_SLEEP_CLOCK_ACCURACY prompt "BLE Sleep Clock Accuracy" depends on BTDM_CTRL_MODE_BLE_ONLY || BTDM_CTRL_MODE_BTDM default BTDM_BLE_DEFAULT_SCA_250PPM help BLE Sleep Clock Accuracy(SCA) for the local device is used to estimate window widening in BLE connection events. With a lower level of clock accuracy(e.g. 500ppm over 250ppm), the slave needs a larger RX window to synchronize with master in each anchor point, thus resulting in an increase of power consumption but a higher level of robustness in keeping connected. According to the requirements of Bluetooth Core specification 4.2, the worst-case accuracy of Classic Bluetooth low power oscialltor(LPO) is +/-250ppm in STANDBY and in low power modes such as sniff. For BLE the worst-case SCA is +/-500ppm. - "151ppm to 250ppm" option is the default value for Bluetooth Dual mode - "251ppm to 500ppm" option can be used in BLE only mode when using external 32kHz crystal as low power clock. This option is provided in case that BLE sleep clock has a lower level of accuracy, or other error sources contribute to the inaccurate timing during sleep. config BTDM_BLE_DEFAULT_SCA_500PPM bool "251ppm to 500ppm" depends on BTDM_CTRL_LPCLK_SEL_EXT_32K_XTAL && BTDM_CTRL_MODE_BLE_ONLY config BTDM_BLE_DEFAULT_SCA_250PPM bool "151ppm to 250ppm" endchoice config BTDM_BLE_SLEEP_CLOCK_ACCURACY_INDEX_EFF int default 0 if BTDM_BLE_DEFAULT_SCA_500PPM default 1 if BTDM_BLE_DEFAULT_SCA_250PPM default 1 config BTDM_BLE_SCAN_DUPL bool "BLE Scan Duplicate Options" depends on (BTDM_CTRL_MODE_BTDM || BTDM_CTRL_MODE_BLE_ONLY) default y help This select enables parameters setting of BLE scan duplicate. choice BTDM_SCAN_DUPL_TYPE prompt "Scan Duplicate Type" default BTDM_SCAN_DUPL_TYPE_DEVICE depends on BTDM_BLE_SCAN_DUPL help Scan duplicate have three ways. one is "Scan Duplicate By Device Address", This way is to use advertiser address filtering. The adv packet of the same address is only allowed to be reported once. Another way is "Scan Duplicate By Device Address And Advertising Data". This way is to use advertising data and device address filtering. All different adv packets with the same address are allowed to be reported. The last way is "Scan Duplicate By Advertising Data". This way is to use advertising data filtering. All same advertising data only allow to be reported once even though they are from different devices. config BTDM_SCAN_DUPL_TYPE_DEVICE bool "Scan Duplicate By Device Address" help This way is to use advertiser address filtering. The adv packet of the same address is only allowed to be reported once config BTDM_SCAN_DUPL_TYPE_DATA bool "Scan Duplicate By Advertising Data" help This way is to use advertising data filtering. All same advertising data only allow to be reported once even though they are from different devices. config BTDM_SCAN_DUPL_TYPE_DATA_DEVICE bool "Scan Duplicate By Device Address And Advertising Data" help This way is to use advertising data and device address filtering. All different adv packets with the same address are allowed to be reported. endchoice config BTDM_SCAN_DUPL_TYPE int depends on BTDM_BLE_SCAN_DUPL default 0 if BTDM_SCAN_DUPL_TYPE_DEVICE default 1 if BTDM_SCAN_DUPL_TYPE_DATA default 2 if BTDM_SCAN_DUPL_TYPE_DATA_DEVICE default 0 config BTDM_SCAN_DUPL_CACHE_SIZE int "Maximum number of devices in scan duplicate filter" depends on BTDM_BLE_SCAN_DUPL range 10 1000 default 100 help Maximum number of devices which can be recorded in scan duplicate filter. When the maximum amount of device in the filter is reached, the cache will be refreshed. config BTDM_BLE_MESH_SCAN_DUPL_EN bool "Special duplicate scan mechanism for BLE Mesh scan" depends on BTDM_BLE_SCAN_DUPL default n help This enables the BLE scan duplicate for special BLE Mesh scan. config BTDM_MESH_DUPL_SCAN_CACHE_SIZE int "Maximum number of Mesh adv packets in scan duplicate filter" depends on BTDM_BLE_MESH_SCAN_DUPL_EN range 10 1000 default 100 help Maximum number of adv packets which can be recorded in duplicate scan cache for BLE Mesh. When the maximum amount of device in the filter is reached, the cache will be refreshed. config BTDM_CTRL_FULL_SCAN_SUPPORTED bool "BLE full scan feature supported" depends on BTDM_CTRL_MODE_BLE_ONLY || BTDM_CTRL_MODE_BTDM default y help The full scan function is mainly used to provide BLE scan performance. This is required for scenes with high scan performance requirements, such as BLE Mesh scenes. config BTDM_BLE_ADV_REPORT_FLOW_CTRL_SUPP bool "BLE adv report flow control supported" depends on (BTDM_CTRL_MODE_BTDM || BTDM_CTRL_MODE_BLE_ONLY) default y help The function is mainly used to enable flow control for advertising reports. When it is enabled, advertising reports will be discarded by the controller if the number of unprocessed advertising reports exceeds the size of BLE adv report flow control. config BTDM_BLE_ADV_REPORT_FLOW_CTRL_NUM int "BLE adv report flow control number" depends on BTDM_BLE_ADV_REPORT_FLOW_CTRL_SUPP range 50 1000 default 100 help The number of unprocessed advertising report that Bluedroid can save.If you set `BTDM_BLE_ADV_REPORT_FLOW_CTRL_NUM` to a small value, this may cause adv packets lost. If you set `BTDM_BLE_ADV_REPORT_FLOW_CTRL_NUM` to a large value, Bluedroid may cache a lot of adv packets and this may cause system memory run out. For example, if you set it to 50, the maximum memory consumed by host is 35 * 50 bytes. Please set `BTDM_BLE_ADV_REPORT_FLOW_CTRL_NUM` according to your system free memory and handle adv packets as fast as possible, otherwise it will cause adv packets lost. config BTDM_BLE_ADV_REPORT_DISCARD_THRSHOLD int "BLE adv lost event threshold value" depends on BTDM_BLE_ADV_REPORT_FLOW_CTRL_SUPP range 1 1000 default 20 help When adv report flow control is enabled, The ADV lost event will be generated when the number of ADV packets lost in the controller reaches this threshold. It is better to set a larger value. If you set `BTDM_BLE_ADV_REPORT_DISCARD_THRSHOLD` to a small value or printf every adv lost event, it may cause adv packets lost more. config BTDM_RESERVE_DRAM hex default 0xdb5c if BT_ENABLED default 0 config BTDM_CTRL_HLI bool "High level interrupt" depends on BT_ENABLED default y help Using Level 4 interrupt for Bluetooth.