// Copyright 2010-2016 Espressif Systems (Shanghai) PTE LTD // // Licensed under the Apache License, Version 2.0 (the "License"); // you may not use this file except in compliance with the License. // You may obtain a copy of the License at // http://www.apache.org/licenses/LICENSE-2.0 // // Unless required by applicable law or agreed to in writing, software // distributed under the License is distributed on an "AS IS" BASIS, // WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. // See the License for the specific language governing permissions and // limitations under the License. #ifndef _ROM_UART_H_ #define _ROM_UART_H_ #include "esp_types.h" #include "esp_attr.h" #ifdef __cplusplus extern "C" { #endif /** \defgroup uart_apis, uart configuration and communication related apis * @brief uart apis */ /** @addtogroup uart_apis * @{ */ #define RX_BUFF_SIZE 0x100 #define TX_BUFF_SIZE 100 //uart int enalbe register ctrl bits #define UART_RCV_INTEN BIT0 #define UART_TRX_INTEN BIT1 #define UART_LINE_STATUS_INTEN BIT2 //uart int identification ctrl bits #define UART_INT_FLAG_MASK 0x0E //uart fifo ctrl bits #define UART_CLR_RCV_FIFO BIT1 #define UART_CLR_TRX_FIFO BIT2 #define UART_RCVFIFO_TRG_LVL_BITS BIT6 //uart line control bits #define UART_DIV_LATCH_ACCESS_BIT BIT7 //uart line status bits #define UART_RCV_DATA_RDY_FLAG BIT0 #define UART_RCV_OVER_FLOW_FLAG BIT1 #define UART_RCV_PARITY_ERR_FLAG BIT2 #define UART_RCV_FRAME_ERR_FLAG BIT3 #define UART_BRK_INT_FLAG BIT4 #define UART_TRX_FIFO_EMPTY_FLAG BIT5 #define UART_TRX_ALL_EMPTY_FLAG BIT6 // include fifo and shift reg #define UART_RCV_ERR_FLAG BIT7 //send and receive message frame head #define FRAME_FLAG 0x7E typedef enum{ UART_LINE_STATUS_INT_FLAG = 0x06, UART_RCV_FIFO_INT_FLAG = 0x04, UART_RCV_TMOUT_INT_FLAG = 0x0C, UART_TXBUFF_EMPTY_INT_FLAG = 0x02 } UartIntType; //consider bit0 for int_flag typedef enum { RCV_ONE_BYTE = 0x0, RCV_FOUR_BYTE = 0x1, RCV_EIGHT_BYTE = 0x2, RCV_FOURTEEN_BYTE = 0x3 } UartRcvFifoTrgLvl; typedef enum { FIVE_BITS = 0x0, SIX_BITS = 0x1, SEVEN_BITS = 0x2, EIGHT_BITS = 0x3 } UartBitsNum4Char; typedef enum { ONE_STOP_BIT = 1, ONE_HALF_STOP_BIT = 2, TWO_STOP_BIT = 3 } UartStopBitsNum; typedef enum { NONE_BITS = 0, ODD_BITS = 2, EVEN_BITS = 3 } UartParityMode; typedef enum { STICK_PARITY_DIS = 0, STICK_PARITY_EN = 2 } UartExistParity; typedef enum { BIT_RATE_9600 = 9600, BIT_RATE_19200 = 19200, BIT_RATE_38400 = 38400, BIT_RATE_57600 = 57600, BIT_RATE_115200 = 115200, BIT_RATE_230400 = 230400, BIT_RATE_460800 = 460800, BIT_RATE_921600 = 921600 } UartBautRate; typedef enum { NONE_CTRL, HARDWARE_CTRL, XON_XOFF_CTRL } UartFlowCtrl; typedef enum { EMPTY, UNDER_WRITE, WRITE_OVER } RcvMsgBuffState; typedef struct { // uint32_t RcvBuffSize; uint8_t *pRcvMsgBuff; uint8_t *pWritePos; uint8_t *pReadPos; uint8_t TrigLvl; //JLU: may need to pad RcvMsgBuffState BuffState; }RcvMsgBuff; typedef struct { uint32_t TrxBuffSize; uint8_t *pTrxBuff; } TrxMsgBuff; typedef enum { BAUD_RATE_DET, WAIT_SYNC_FRM, SRCH_MSG_HEAD, RCV_MSG_BODY, RCV_ESC_CHAR, } RcvMsgState; typedef struct{ UartBautRate baut_rate; UartBitsNum4Char data_bits; UartExistParity exist_parity; UartParityMode parity; // chip size in byte UartStopBitsNum stop_bits; UartFlowCtrl flow_ctrl; uint8_t buff_uart_no; //indicate which uart use tx/rx buffer uint8_t tx_uart_no; RcvMsgBuff rcv_buff; // TrxMsgBuff trx_buff; RcvMsgState rcv_state; int received; } UartDevice; /** * @brief Init uart device struct value and reset uart0/uart1 rx. * Please do not call this function in SDK. * * @param None * * @return None */ void uartAttach(); /** * @brief Init uart0 or uart1 for UART download booting mode. * Please do not call this function in SDK. * * @param uint8_t uart_no : 0 for UART0, else for UART1. * * @param uint32_t clock : clock used by uart module, to adjust baudrate. * * @return None */ void Uart_Init(uint8_t uart_no, uint32_t clock); /** * @brief Modify uart baudrate. * This function will reset RX/TX fifo for uart. * * @param uint8_t uart_no : 0 for UART0, 1 for UART1. * * @param uint32_t DivLatchValue : (clock << 4)/baudrate. * * @return None */ void uart_div_modify(uint8_t uart_no, uint32_t DivLatchValue); /** * @brief Init uart0 or uart1 for UART download booting mode. * Please do not call this function in SDK. * * @param uint8_t uart_no : 0 for UART0, 1 for UART1. * * @param uint8_t is_sync : 0, only one UART module, easy to detect, wait until detected; * 1, two UART modules, hard to detect, detect and return. * * @return None */ int uart_baudrate_detect(uint8_t uart_no, uint8_t is_sync); /** * @brief Switch printf channel of uart_tx_one_char. * Please do not call this function when printf. * * @param uint8_t uart_no : 0 for UART0, 1 for UART1. * * @return None */ void uart_tx_switch(uint8_t uart_no); /** * @brief Switch message exchange channel for UART download booting. * Please do not call this function in SDK. * * @param uint8_t uart_no : 0 for UART0, 1 for UART1. * * @return None */ void uart_buff_switch(uint8_t uart_no); /** * @brief Output a char to printf channel, wait until fifo not full. * * @param None * * @return OK. */ STATUS uart_tx_one_char(uint8_t TxChar); /** * @brief Output a char to message exchange channel, wait until fifo not full. * Please do not call this function in SDK. * * @param None * * @return OK. */ STATUS uart_tx_one_char2(uint8_t TxChar);//for send message /** * @brief Wait until uart tx full empty. * * @param uint8_t uart_no : 0 for UART0, 1 for UART1. * * @return None. */ void uart_tx_flush(uint8_t uart_no); /** * @brief Wait until uart tx full empty and the last char send ok. * * @param uint8_t uart_no : 0 for UART0, 1 for UART1. * * @return None. */ void uart_tx_wait_idle(uint8_t uart_no); /** * @brief Get an input char from message channel. * Please do not call this function in SDK. * * @param uint8_t* pRxChar : the pointer to store the char. * * @return OK for successful. * FAIL for failed. */ STATUS uart_rx_one_char(uint8_t* pRxChar); /** * @brief Get an input char to message channel, wait until successful. * Please do not call this function in SDK. * * @param None * * @return char : input char value. */ char uart_rx_one_char_block(void); /** * @brief Get an input string line from message channel. * Please do not call this function in SDK. * * @param uint8_t* pString : the pointer to store the string. * * @param uint8_t MaxStrlen : the max string length, incude '\0'. * * @return OK. */ STATUS UartRxString(uint8_t* pString, uint8_t MaxStrlen); /** * @brief Process uart recevied information in the interrupt handler. * Please do not call this function in SDK. * * @param void * para : the message receive buffer. * * @return None */ void uart_rx_intr_handler(void * para); /** * @brief Get an char from receive buffer. * Please do not call this function in SDK. * * @param RcvMsgBuff* pRxBuff : the pointer to the struct that include receive buffer. * * @param uint8_t* pRxByte : the pointer to store the char. * * @return OK for successful. * FAIL for failed. */ STATUS uart_rx_readbuff( RcvMsgBuff* pRxBuff, uint8_t* pRxByte); /** * @brief Get all chars from receive buffer. * Please do not call this function in SDK. * * @param uint8_t * pCmdLn : the pointer to store the string. * * @return OK for successful. * FAIL for failed. */ STATUS UartGetCmdLn(uint8_t * pCmdLn); /** * @brief Get uart configuration struct. * Please do not call this function in SDK. * * @param None * * @return UartDevice * : uart configuration struct pointer. */ UartDevice * GetUartDevice(); /** * @brief Send an packet to download tool, with ESC char. * Please do not call this function in SDK. * * @param uint8_t * p : the pointer to output string. * * @param int len : the string length. * * @return None. */ void send_packet(uint8_t *p, int len); /** * @brief Receive an packet from download tool, with ESC char. * Please do not call this function in SDK. * * @param uint8_t * p : the pointer to input string. * * @param int len : If string length > len, the string will be truncated. * * @param uint8_t is_sync : 0, only one UART module; * 1, two UART modules. * * @return int : the length of the string. */ int recv_packet(uint8_t *p, int len, uint8_t is_sync); /** * @brief Send an packet to download tool, with ESC char. * Please do not call this function in SDK. * * @param uint8_t * pData : the pointer to input string. * * @param uint16_t DataLen : the string length. * * @return OK for successful. * FAIL for failed. */ STATUS SendMsg(uint8_t *pData, uint16_t DataLen); /** * @brief Receive an packet from download tool, with ESC char. * Please do not call this function in SDK. * * @param uint8_t * pData : the pointer to input string. * * @param uint16_t MaxDataLen : If string length > MaxDataLen, the string will be truncated. * * @param uint8_t is_sync : 0, only one UART module; * 1, two UART modules. * * @return OK for successful. * FAIL for failed. */ STATUS RcvMsg(uint8_t *pData, uint16_t MaxDataLen, uint8_t is_sync); extern UartDevice UartDev; /** * @} */ #ifdef __cplusplus } #endif #endif /* _ROM_UART_H_ */