menu "Example Configuration" choice EXAMPLE_USE_ETHERNET prompt "Ethernet Type" default EXAMPLE_USE_INTERNAL_ETHERNET if IDF_TARGET_ESP32 default EXAMPLE_USE_DM9051 if !IDF_TARGET_ESP32 help Select which kind of Ethernet will be used in the example. config EXAMPLE_USE_INTERNAL_ETHERNET depends on IDF_TARGET_ESP32 select ETH_USE_ESP32_EMAC bool "Internal EMAC" help Select internal Ethernet MAC controller. config EXAMPLE_USE_DM9051 bool "DM9051 Module" select ETH_USE_SPI_ETHERNET select ETH_SPI_ETHERNET_DM9051 help Select external SPI-Ethernet module (DM9051). endchoice if EXAMPLE_USE_INTERNAL_ETHERNET choice EXAMPLE_ETH_PHY_MODEL prompt "Ethernet PHY Device" default EXAMPLE_ETH_PHY_IP101 help Select the Ethernet PHY device to use in the example. config EXAMPLE_ETH_PHY_IP101 bool "IP101" help IP101 is a single port 10/100 MII/RMII/TP/Fiber Fast Ethernet Transceiver. Goto http://www.icplus.com.tw/pp-IP101G.html for more information about it. config EXAMPLE_ETH_PHY_RTL8201 bool "RTL8201/SR8201" help RTL8201F/SR8201F is a single port 10/100Mb Ethernet Transceiver with auto MDIX. Goto http://www.corechip-sz.com/productsview.asp?id=22 for more information about it. config EXAMPLE_ETH_PHY_LAN8720 bool "LAN8720" help LAN8720A is a small footprint RMII 10/100 Ethernet Transceiver with HP Auto-MDIX Support. Goto https://www.microchip.com/LAN8720A for more information about it. config EXAMPLE_ETH_PHY_DP83848 bool "DP83848" help DP83848 is a single port 10/100Mb/s Ethernet Physical Layer Transceiver. Goto http://www.ti.com/product/DP83848J for more information about it. config EXAMPLE_ETH_PHY_KSZ8041 bool "KSZ8041" help The KSZ8041 is a single supply 10Base-T/100Base-TX Physical Layer Transceiver. Goto https://www.microchip.com/wwwproducts/en/KSZ8041 for more information about it. endchoice config EXAMPLE_ETH_MDC_GPIO int "SMI MDC GPIO number" default 23 help Set the GPIO number used by SMI MDC. config EXAMPLE_ETH_MDIO_GPIO int "SMI MDIO GPIO number" default 18 help Set the GPIO number used by SMI MDIO. endif if EXAMPLE_USE_DM9051 config EXAMPLE_DM9051_SPI_HOST int "SPI Host Number" range 0 2 default 1 help Set the SPI host used to communicate with the SPI Ethernet Controller. config EXAMPLE_DM9051_SCLK_GPIO int "SPI SCLK GPIO number" range 0 33 default 19 help Set the GPIO number used by SPI SCLK. config EXAMPLE_DM9051_MOSI_GPIO int "SPI MOSI GPIO number" range 0 33 default 23 help Set the GPIO number used by SPI MOSI. config EXAMPLE_DM9051_MISO_GPIO int "SPI MISO GPIO number" range 0 33 default 25 help Set the GPIO number used by SPI MISO. config EXAMPLE_DM9051_CS_GPIO int "SPI CS GPIO number" range 0 33 default 22 help Set the GPIO number used by SPI CS. config EXAMPLE_DM9051_SPI_CLOCK_MHZ int "SPI clock speed (MHz)" range 5 80 default 20 help Set the clock speed (MHz) of SPI interface. config EXAMPLE_DM9051_INT_GPIO int "Interrupt GPIO number" default 4 help Set the GPIO number used by DM9051 interrupt. endif config EXAMPLE_ETH_PHY_RST_GPIO int "PHY Reset GPIO number" default 5 help Set the GPIO number used to reset PHY chip. Set to -1 to disable PHY chip hardware reset. config EXAMPLE_ETH_PHY_ADDR int "PHY Address" range 0 31 if EXAMPLE_USE_INTERNAL_ETHERNET range 1 1 if !EXAMPLE_USE_INTERNAL_ETHERNET default 1 help Set PHY address according your board schematic. endmenu