menu "OpenThread" config OPENTHREAD_ENABLED bool "OpenThread" default n help Select this option to enable OpenThread and show the submenu with OpenThread configuration choices. config OPENTHREAD_LOG_LEVEL_DYNAMIC bool "Enable dynamic log level control" depends on OPENTHREAD_ENABLED default y help Select this option to enable dynamic log level control for OpenThread choice OPENTHREAD_LOG_LEVEL prompt "OpenThread log verbosity" depends on OPENTHREAD_ENABLED && !OPENTHREAD_LOG_LEVEL_DYNAMIC default OPENTHREAD_LOG_LEVEL_INFO help Select OpenThread log level. config OPENTHREAD_LOG_LEVEL_NONE bool "No logs" config OPENTHREAD_LOG_LEVEL_CRIT bool "Error logs" config OPENTHREAD_LOG_LEVEL_WARN bool "Warning logs" config OPENTHREAD_LOG_LEVEL_NOTE bool "Notice logs" config OPENTHREAD_LOG_LEVEL_INFO bool "Info logs" config OPENTHREAD_LOG_LEVEL_DEBG bool "Debug logs" endchoice #OPENTHREAD_LOG_LEVEL menu "Thread Operational Dataset" config OPENTHREAD_NETWORK_NAME string "OpenThread network name" default "OpenThread-ESP" config OPENTHREAD_MESH_LOCAL_PREFIX string "OpenThread mesh local prefix, format
/" default "fd00:db8:a0:0::/64" help A string in the format "
/", where `
` is an IPv6 address and `` is a prefix length. For example "fd00:db8:a0:0::/64" config OPENTHREAD_NETWORK_CHANNEL int "OpenThread network channel" range 11 26 default 15 config OPENTHREAD_NETWORK_PANID hex "OpenThread network pan id" range 0 0xFFFE default 0x1234 config OPENTHREAD_NETWORK_EXTPANID string "OpenThread extended pan id" default "dead00beef00cafe" help The OpenThread network extended pan id in hex string format config OPENTHREAD_NETWORK_MASTERKEY string "OpenThread network key" default "00112233445566778899aabbccddeeff" help The OpenThread network network key in hex string format config OPENTHREAD_NETWORK_PSKC string "OpenThread pre-shared commissioner key" default "104810e2315100afd6bc9215a6bfac53" help The OpenThread pre-shared commissioner key in hex string format endmenu config OPENTHREAD_LOG_LEVEL int depends on OPENTHREAD_ENABLED && !OPENTHREAD_LOG_LEVEL_DYNAMIC default 0 if OPENTHREAD_LOG_LEVEL_NONE default 1 if OPENTHREAD_LOG_LEVEL_CRIT default 2 if OPENTHREAD_LOG_LEVEL_WARN default 3 if OPENTHREAD_LOG_LEVEL_NOTE default 4 if OPENTHREAD_LOG_LEVEL_INFO default 5 if OPENTHREAD_LOG_LEVEL_DEBG choice OPENTHREAD_RADIO_TYPE prompt "Config the Thread radio type" depends on OPENTHREAD_ENABLED default OPENTHREAD_RADIO_NATIVE if SOC_IEEE802154_SUPPORTED default OPENTHREAD_RADIO_SPINEL_UART help Configure how OpenThread connects to the 15.4 radio config OPENTHREAD_RADIO_NATIVE bool "Native 15.4 radio" help Select this to use the native 15.4 radio. config OPENTHREAD_RADIO_SPINEL_UART bool "Connect via UART" help Select this to connect to a Radio Co-Processor via UART. config OPENTHREAD_RADIO_SPINEL_SPI bool "Connect via SPI" help Select this to connect to a Radio Co-Processor via SPI. endchoice choice OPENTHREAD_DEVICE_TYPE prompt "Config the Thread device type" depends on OPENTHREAD_ENABLED default OPENTHREAD_FTD help OpenThread can be configured to different device types (FTD, MTD, Radio) config OPENTHREAD_FTD bool "Full Thread Device" help Select this to enable Full Thread Device which can act as router and leader in a Thread network. config OPENTHREAD_MTD bool "Minimal Thread Device" help Select this to enable Minimal Thread Device which can only act as end device in a Thread network. This will reduce the code size of the OpenThread stack. config OPENTHREAD_RADIO bool "Radio Only Device" help Select this to enable Radio Only Device which can only forward 15.4 packets to the host. The OpenThread stack will be run on the host and OpenThread will have minimal footprint on the radio only device. endchoice choice OPENTHREAD_RCP_TRANSPORT prompt "The RCP transport type" depends on OPENTHREAD_RADIO default OPENTHREAD_RCP_UART config OPENTHREAD_RCP_UART bool "UART RCP" help Select this to enable UART connection to host. config OPENTHREAD_RCP_SPI bool "SPI RCP" help Select this to enable SPI connection to host. endchoice config OPENTHREAD_CLI bool "Enable Openthread Command-Line Interface" depends on OPENTHREAD_ENABLED default y help Select this option to enable Command-Line Interface in OpenThread. config OPENTHREAD_DIAG bool "Enable diag" depends on OPENTHREAD_ENABLED default y help Select this option to enable Diag in OpenThread. This will enable diag mode and a series of diag commands in the OpenThread command line. These commands allow users to manipulate low-level features of the storage and 15.4 radio. config OPENTHREAD_COMMISSIONER bool "Enable Commissioner" depends on OPENTHREAD_ENABLED default n help Select this option to enable commissioner in OpenThread. This will enable the device to act as a commissioner in the Thread network. A commissioner checks the pre-shared key from a joining device with the Thread commissioning protocol and shares the network parameter with the joining device upon success. config OPENTHREAD_JOINER bool "Enable Joiner" depends on OPENTHREAD_ENABLED default n help Select this option to enable Joiner in OpenThread. This allows a device to join the Thread network with a pre-shared key using the Thread commissioning protocol. config OPENTHREAD_SRP_CLIENT bool "Enable SRP Client" depends on OPENTHREAD_ENABLED default y help Select this option to enable SRP Client in OpenThread. This allows a device to register SRP services to SRP Server. config OPENTHREAD_DNS_CLIENT bool "Enable DNS Client" depends on OPENTHREAD_ENABLED default y help Select this option to enable DNS Client in OpenThread. config OPENTHREAD_BORDER_ROUTER bool "Enable Border Router" depends on OPENTHREAD_ENABLED default n help Select this option to enable border router features in OpenThread. config OPENTHREAD_PLATFORM_MSGPOOL_MANAGEMENT bool 'Allocate message pool buffer from PSRAM' depends on OPENTHREAD_ENABLED && (SPIRAM_USE_CAPS_ALLOC || SPIRAM_USE_MALLOC) default n help If enabled, the message pool is managed by platform defined logic. config OPENTHREAD_NUM_MESSAGE_BUFFERS int "The number of openthread message buffers" depends on OPENTHREAD_ENABLED default 65 range 10 100 if !OPENTHREAD_PLATFORM_MSGPOOL_MANAGEMENT range 10 8191 if OPENTHREAD_PLATFORM_MSGPOOL_MANAGEMENT config OPENTHREAD_DNS64_CLIENT bool "Use dns64 client" depends on OPENTHREAD_ENABLED && LWIP_IPV4 default n help Select this option to acquire NAT64 address from dns servers. config OPENTHREAD_DNS_SERVER_ADDR string "DNS server address (IPv4)" depends on OPENTHREAD_DNS64_CLIENT default "8.8.8.8" help Set the DNS server IPv4 address. config OPENTHREAD_UART_BUFFER_SIZE int "The uart received buffer size of openthread" depends on OPENTHREAD_ENABLED default 256 range 128 1024 help Set the OpenThread UART buffer size. config OPENTHREAD_LINK_METRICS bool "Enable link metrics feature" depends on OPENTHREAD_ENABLED default n help Select this option to enable link metrics feature config OPENTHREAD_MACFILTER_ENABLE bool "Enable mac filter feature" depends on OPENTHREAD_ENABLED default n help Select this option to enable mac filter feature config OPENTHREAD_CSL_ENABLE bool "Enable CSL feature" depends on OPENTHREAD_ENABLED default n help Select this option to enable CSL feature config OPENTHREAD_CSL_DEBUG_ENABLE bool "Enable CSL debug" depends on OPENTHREAD_CSL_ENABLE default n help Select this option to set rx on when sleep in CSL feature, only for debug config OPENTHREAD_DUA_ENABLE bool "Enable Domain Unicast Address feature" depends on OPENTHREAD_ENABLED default n help Only used for Thread1.2 certification endmenu