The implementation was previously hardcoded to use only the non-expanded
IETF EAP methods in Phase 2. Extend that to allow vendor EAP methods
with expanded header to be used.
Signed-off-by: Jouni Malinen <j@w1.fi>
EAP-TLS with TLS 1.3 uses an empty application data record from the
server to indicate end of the exchange, so EAP-TLS peer will need to
check for this special case and finish the exchange with an empty
EAP-TLS (ACK) so that the server can send out EAP-Success.
Signed-off-by: Jouni Malinen <j@w1.fi>
Allow an additional context value to be passed to TLS exporter as
specified in RFC 5705 section 4.
This does not yet implement it for the internal TLS implementation.
However, as currently nothing uses context yet, this will not break
anything right now. WolfSSL maintainers also stated that they are not
going to add context support yet, but would look into it if/when this is
required by a published draft or a standard.
Signed-off-by: Ervin Oro <ervin.oro@aalto.fi>
These buffers in TLS-based EAP methods might contain keys or password
(e.g., when using TTLS-PAP or PEAP-GTC), so clear them explicitly to
avoid leaving such material into heap memory unnecessarily.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Derive EMSK when using EAP-PEAP to enable ERP. In addition, change the
MSK derivation for EAP-PEAP to always derive 128 octets of key material
instead of the 64 octets to cover just the MSK. This is needed with the
PRF used in TLS 1.3 since the output length is mixed into the PRF
context.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reduce the amount of time keying material (MSK, EMSK, temporary private
data) remains in memory in EAP methods. This provides additional
protection should there be any issues that could expose process memory
to external observers.
Signed-off-by: Jouni Malinen <j@w1.fi>
Move to the version used in draft-ietf-emu-eap-tls13-03.txt, i.e.,
include the 0x0D prefix and use a different TLS-Exporter() label string.
Signed-off-by: Jouni Malinen <j@w1.fi>
The label strings used for deriving Key_Material with TLS v1.3 were
changed, so update the implementation to match the new values.
Signed-off-by: Jouni Malinen <j@w1.fi>
The EAP session cannot be marked fully completed on sending Client
Finished with TLS v1.3 since the server may still send NewSessionTicket
before EAP-Success.
Signed-off-by: Jouni Malinen <j@w1.fi>
With TLS v1.3, the Finished message from the client can require
fragmentation. Postpone key derivation and marking of the EAP session
fully completed until all the fragments of that last message are sent to
avoid losing all the subsequent fragments.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds support for optional functionality to validate server
certificate chain in TLS-based EAP methods in an external program.
wpa_supplicant control interface is used to indicate when such
validation is needed and what the result of the external validation is.
This external validation can extend or replace the internal validation.
When ca_cert or ca_path parameter is set, the internal validation is
used. If these parameters are omitted, only the external validation is
used. It needs to be understood that leaving those parameters out will
disable most of the validation steps done with the TLS library and that
configuration is not really recommend.
By default, the external validation is not used. It can be enabled by
addingtls_ext_cert_check=1 into the network profile phase1 parameter.
When enabled, external validation is required through the CTRL-REQ/RSP
mechanism similarly to other EAP authentication parameters through the
control interface.
The request to perform external validation is indicated by the following
event:
CTRL-REQ-EXT_CERT_CHECK-<id>:External server certificate validation needed for SSID <ssid>
Before that event, the server certificate chain is provided with the
CTRL-EVENT-EAP-PEER-CERT events that include the cert=<hexdump>
parameter. depth=# indicates which certificate is in question (0 for the
server certificate, 1 for its issues, and so on).
The result of the external validation is provided with the following
command:
CTRL-RSP-EXT_CERT_CHECK-<id>:<good|bad>
It should be noted that this is currently enabled only for OpenSSL (and
BoringSSL/LibreSSL). Due to the constraints in the library API, the
validation result from external processing cannot be reported cleanly
with TLS alert. In other words, if the external validation reject the
server certificate chain, the pending TLS handshake is terminated
without sending more messages to the server.
Signed-off-by: Jouni Malinen <j@w1.fi>
This commit fixes a potential issue of illegal memory access when
accessing the various task lists in FreeRTOS while fetching tasks using
the xTaskGetNext() function.
Fix issues with DPP stop listen and DPP auth data deinit
Closes WIFIBUG-443, WIFIBUG-442, WIFIBUG-421, and WIFIBUG-423
See merge request espressif/esp-idf!29404
- move .tbss to NOLOAD section
- remove xtensa-specific entities from riscv scripts
- explicit eh_frame terminator instead of "align magic"
- 80 characters line length limit
- refactor comments
- discard .rela sections (the rela data will go to relates sections)
fix(i2c_master): Fix issue that initialize esp32 fails and using i2c_master_probe issue IF NO PULL-UP ON PINS. And add nack check
Closes IDFGH-11838, IDFGH-13142, and IDFGH-13398
See merge request espressif/esp-idf!29667
Enable FTM Responder mode for ESP32C6. Update wifi libs with below -
1. Break FTM State Machine code into separate functions
2. Use dynamic allocation for FTM session to save memory
3. Add API to get FTM report instead of event based mechanism
4. Add FTM Request retry and comeback support
Closes https://github.com/espressif/esp-idf/issues/6810
