Prevent a remote device from doing a Bluetooth Impersonation Attack
(BIAS) by:
- Preventing remote device to downgrade secure connection
feature mask. Secure connection feature mask should remain same or
increase to enabled in link key generation and authentication.
- Doing a mutual authentication during Legacy Authentication.
Signed-off-by: Chinmay Chhajed <chinmay.chhajed@espressif.com>
1. Improve WiFi throughput in some Classic BT scienarios(idle, inquire scan,
connected, sniff, a2dp pause, etc).
2. Support WiFi + Classic BT + BLE mesh coexistence scienario.
3. Improve WiFi scan and connect succeed ratio in coexistence scienario.
4. Do not support to choose software coexistence preference anymore for it is
determined according to coexistence scienario automatically.
components/lwip: increase TCP send buffer and receive window limitation when TCP window scale is enabled
components/ble_mesh: Fix some bugs about ble mesh
1. fix send acl pkt after ble have sent terminate ind modify min adv interval to 10ms.
1. Fix high beacon and broadcast packets loss ratio of WiFi to make
MDNS test pass.
2. Improve stability of WiFi performance with a little
sacrifice of throughput.
3. Improve BLE advertising and connection performance with dynamic
priority. It sacrifices a little WiFi throughput, but achieves balance
between WiFi and Bluetooth.
1. BLE Mesh Core
* Provisioning: Node Role
* Advertising and GATT bearer
* Authentication OOB
* Provisioning: Provisioner Role
* Advertising and GATT bearer
* Authentication OOB
* Networking
* Relay
* Segmentation and Reassembly
* Key Refresh
* IV Update
* Proxy Support
* Multiple Client Models Run Simultaneously
* Support multiple client models send packets to different nodes simultaneously
* No blocking between client model and server
* NVS Storage
* Store Provisioning Data of BLE Mesh Nodes in Flash
2. BLE Mesh Applications
* BLE Mesh Node & Provisioner
* Node Example
* Provisioner Example
* Node + Generic OnOff Client Example
* Fast Provisioning
* Vendor Fast Prov Server Model
* Vendor Fast Prov Client Model
* Examples
* Wi-Fi & BLE Mesh Coexistence
* Example
* BLE Mesh Console Commands
* Example
3. BLE Mesh Models
* Foundation Models
* Configuration Server Model
* Configuration Client Model
* Health Server Model
* Health Client Model
* Generic Client Models
* Generic OnOff Client
* Generic Level Client
* Generic Location Client
* Generic Default Transition Timer Client
* Generic Power OnOff Client
* Generic Power Level Client
* Generic Battery Client
* Generic Property Client
* Generic Server Models
* Generic OnOff Server (Example)
* Lighting Client Models
* Light Lightness Client
* Light CTL Client
* Light HSL Client
* Light xyL Client
* Light LC Client
* Sensor Client Model
* Sensor Client
* Time and Scenes Client Models
* Time Client
* Scene Client
* Scheduler Client
Originally, when doing BLE active scan, Bluedroid will not report adv to
application layer until receive scan response. This option is used to
disable the behavior. When enable this option, Bluedroid will report
adv data or scan response to application layer immediately.
1. start an esp_timer on entering sleep to acquire pm_lock before wake up from modem sleep
2. decrease the clock division of XTAL fed to bluetooth low power clock from 32us to 2us period to allow to work under 240MHz Max CPU frequency
3. decrease the minimum sleep duration threshold to allow shorter bluetooth modem sleep period, especially for BLE with short connection interval
4. reconfigure bluetooth baseband(BT-BB) settings after PHY/RF init upon waking up from modem sleep to avoid packet RX/TX performance degradation
1. BLE only with 9(max) connection will decrease 3K DRAM
2. BR/EDR only with 7(max) connection will decrease 16K DRAM
3. Any of BLE or BR/EDR connection number decrease will also decrease DRAM consumption
4. Decrease one BLE connection will save about 1KB DRAM
5. Decrease one BR/EDR ACL connection will save about 1.2KB DRAM
6. Decrease one BR/EDR SCO/eSCO will save 2KB DRAM.
7. fix some definition and kconfig
8. remove 1.2k of vhci tx cache and make .bss & .data to heap about 1.4K
9. modify BT Reserved Memory size and modify example to support new bt kconfig
Earlier they have to be selected at the compile time through sdkconfig.
A2DP sink and source application tested with this change.
Signed-off-by: Amey Inamdar <amey@espressif.com>
