Hardware AES-CBC performance changes:
Release config 11.0MB/sec -> 10.8MB/sec
Debug config 9.4MB/sec -> 9.8MB/sec
(Unrolling the loop to optimize the check improves
performance at -Og, even with the fault check.)
If httpd_sess_trigger_close() gets called twice for the same socket,
the first httpd_sess_close() cb closes the correct socket, but the second
invocation closes the wrong socket which was just accepted and added to
the socket db. Checking for the lru counter will help identify this as the
counter is set only for requests actually served.
1. Bugfix btdm sleep twice after wakeup request
2. Fix connect fail duo to loop of send extended feature request
3. Clear BT/BLE interrupts after controller_disable to overwrite the default non-zero value of intcntl registers
Try to allocate some Lw-ip memories in SPIRAM first. If failed, try to allocate in internal RAM then.(Backport v3.2)
See merge request espressif/esp-idf!5719
Made MMU pages available check in `esp_image_format.c`
This now makes it possible to map and process bootoader image as well in chunks when image doesn't fit completely into available free pages.
Signed-off-by: Vikram Dattu <vikram.dattu@espressif.com>
There are lot of prints of `Allocate TX buffer for DMA`
Changed these from `ESP_LOGI` to `ESP_LOGD`
Signed-off-by: Vikram Dattu <vikram.dattu@espressif.com>
1. resend eb which are pending in g_ic.tx_buf due to channel switch.
2. add lock for mgmg/xon/bcast to protect send from user flush.
3. softap: add check if secondary offset is correct when start softap.
4. softap: in inactive timer handler, add check if child bss is removed to avoid removing it again.
5. disable A-MPDU for non-root.
6. fix reusing a freed eb.
7. fix when node becomes root, it does not record assoc value to nvs.
8. discard unnecessary forwarded group packets.
9. fix toDS state is not updated in time.
10. fix s_sta_cnx_times is not cleared when deinit causes root sends ADD annoucement.
11. root: increase beacon timeout time from 6 seconds to 15 seconds to delay initiation of reconnection.
12. add esp_mesh_get_tsf_time to return TSF time.
13. send the whole routing table multi-times.
14. clear candidate settings if not receive candidate beacon within 8 seconds.
When flash work in DIO Mode, in order to ensure the fast read mode of flash
is a fixed value, we merged the mode bits into address part, and the fast
read mode value is 0 (the default value).
List of changes:
* Use 128 bit characteristic UUIDs when creating GATT table entries
* Change primary service attribute value to 128 bit custom service UUID
* Use raw advertisement data to convey flags and 128 bit primary service UUID
* Use raw scan response to send device name as complete local name
* Increase maximum device name length in relation to maximum scan response length
* Set Characteristic User Description attributes for each characteristic to convey protocomm endpoint names
These changes guarantee that the SSID and Passphrase received via protocomm are NULL terminated and size limited to their standard lengths.
List of changes:
* Corrected length of passphrase field in wifi_prov_config_set_data_t structure
* Performing length checks on SSID, passphrase and bssid, when populating wifi_prov_config_set_data_t structure with received credentials
1. modify the limit of frames to send to avoid dropping packet on A2DP source due to TX data queue overflow
2. reduce the A2DP source data queue size in order to achieve faster control respnonse
xTaskIncrementTick have to unwind uxPendedTicks on CPU1 and CPU0.
Use case: If an erase operation was run on the CPU1 then it leads
to starving other tasks which waiting time. Waited tasks just skipped.
Closes: https://github.com/espressif/esp-idf/issues/1952
Closes: IDF-183
Issue is that when users creates a custom bootloader from
$IDF_PATH/components/bootloader. Parent project build uses the copy but
bootloader subproject build uses the original still. The issue is solved
by passing the custom bootloader as extra component directory so
bootloader build knows to use the new copy (itself) in the build.
Fixed the case when the first part of log was missed
this was happened when:
* CONFIG_CONSOLE_UART_CUSTOM option is selected (UART1)
* The selected CONSOLE_UART port is used also for the console component
* in code esp_restart() or abort() functions were called.
List of changes:
* Kconfig option HTTPD_LOG_PURGE_DATA enables logging of purged data
* Kconfig option HTTPD_PURGE_BUF_LEN sets purge buffer length
* Purged data is logged in hex
Closes https://github.com/espressif/esp-idf/issues/3359
Previous version read all data to the buffer including header which reduced maximum payload read. This version uses a local array to receive header and reads payload bytes to the buffer
cherry-picked from db121a56e1
Earlier eraseItem function in Storage class would do lazy cleanup of
multi-page blobs if called using type "ANY" instead of "BLOB". It used to
just delete BLOB data and index would remain as is. Any subsequent read
would delete index entry as well. This however would return a valid
length without error if nvs_get_blob API was just used for finding
length and not reading the complete blob. This change fixes this issue.
Closes https://github.com/espressif/esp-idf/issues/3255
Backport following WiFi fixes to v3.2:
1. Add support for STA HT2040 coexist management
2. Add support for WPA2 improvements
3. Disallow HT rate when unicast/mcast cipher is TKIP/WEP
4. Add support for signal test
5. Fix the bug that WPS fails when AP is encrypted
List of changes:
* When parsing requests, count termination from LF characters only
* Correct memcpy() length parameter in httpd_unrecv() (pointed out by jimparis in GitHub issue thread)
* Use ssize_t to store results of length subtractions during parsing
* Modify some comments to reduce ambiguity
Closes https://github.com/espressif/esp-idf/issues/3182
Fixed adjtime function: While using the adjtime() function,
the time correction accumulated an error
when reading the time frequently (using gettimeofday).
Operation:
In `esp_http_client_set_url`, we check for if old_host is same as new_host.
Delete and open new connection if host is different.
Issue:
We just pointed `client->connection_info.host` to `old_host` and reassigned it.
This made old_host and new_host always point to same location and hence, using old_host with new request.
Fix:
Made a separate copy for old_host using strdup.
Closes https://github.com/espressif/esp-idf/issues/2631
Signed-off-by: Vikram Dattu <vikram.dattu@espressif.com>
1. remove redundant SPI clock settings, use rom functions to set clock.
2. remove redundant SPI cs setup and hold settings.
3. for old 32Mbit psram, cs hold time must only be 0.5T due to the special driving mode.(cs_setup = 0; cs_hold = 0)
4. for new 64Mbit psram, cs hold time is recommended to be 2.5T. (cs_setup = 1, cs_setup_time = 0;cs_hold = 1, cs_hold_time = 1)
1. Softap support multicast and broadcast saving and flushing
when the associated stations enable IEEE80211 legacy power
save(which is called modem sleep in ESP32).
2. Improve the frame saving and flushing mechanism of softap power
save.
Fix following WiFi and coexist bugs:
1. Fix BT disconnecting due to too many reset BB
2. Fix the bug that no TBTT is generated after rx wrong beacon when WiFi/BT coexist
3. Fix a DelBA bug
4. Add out of memory check
5. Fix the bug that STA incorrectly receives packets when scanning in connected status
6. PHY4008: Disable BT TX in force wifi mode, and enable BT TX in un-force wifi mode
1. fix the bug block scan tiemout before scan finish
2. make menuconfig can set the WiFi mgmt short buffer num
3. modify wifi reason code
4. fix the bug PMK recal too long
1.Fix memory leak when set txpower
2.Fix some bugs
Disconnect with apple device
hci_refresh_enc_key_cmd will be ignore
hci_refresh_enc_key_cmd will crash
1. Pass the correct conn_id to protocomm_req_handle
In transport_simple_ble_write(), passing param->exec_write.conn_id would
be invalid. Instead param->write.conn_id should be passed
Similar change in transport_simple_ble_exec_write() to use
param->exec_write.conn_id
2. simple_ble_start() assumes that the mode is BLE only and enables
Bluetooth controller accordingly. For, cases having BT + BLE like Alexa
(Provisioning over BLE + Audio over classic BT), this assumption should
be removed.
This fix prevents HTTP server from accepting new connections when the total count of connected
sockets has reached the max_open_sockets limit set during configuration. The pending connections
are kept in backlog until atleast one of the connected sockets is closed. The maximum number of
connection requests that can kept in backlog is specified as backlog_conn configuration option.
Note that this modification has no effect when LRU purge is enabled.
Also added sanity check on setting for max_open_sockets during configuration.
Solution suggested by jimparis https://github.com/espressif/esp-idf/issues/3183#issue-421234265
Closes https://github.com/espressif/esp-idf/issues/3183
The requirements of pin capabilites is different for spi master and
slave. The master needs CS, SCLK, MOSI to be output-able, while slave
needs MISO to be output-able.
Previous code is for master only.
This commit allows to place other 3 pins than MISO on input-only pins
for slaves. Refactoring for spi_common is also included.
Resolves https://github.com/espressif/esp-idf/issues/2455
Issue: MDNS server initially sends probing packets to resolve naming confilicts with already registered service instances. In case of a conflict, instance name is altered and probing restarts. Original instance however wasnnot removed from the structure and upon service removal only one entry was removed and a dangling service might have been kept in the structure to bring about a crash.
Resolution: Keep only one instance of a service in the probing structure.
Closes IDF-438
possible race condition: user task runs mdns_init, which enables pcbs while mdns-task already created could execute enable/disable of the same pcbs if an appropriate system event received
mnds_free() initiates stop and delete timer tasks, which after locking the mutex could lead to a dead lock in case timer task executed before deleting the task, as it would wait indefinitelly for unlocking the mutex. This condition is fixed by calling _mdns_stop_timer without locking the mutex, because there's no need to protect any data when stopping and deleting the timer task
Closes https://github.com/espressif/esp-idf/issues/1696
Issue: mdns_service_add API allocates and queues an action to be processed in mdns task context; when allocation or queueing fails, allocated structure needs to be freed. Function _mdns_free_service did not only fee all the structures, but also updates packet data.
Resolution: Moved removal of packet data outside of _mdns_free_service function.
packets scheduled to transmit are pushed to action queue and removed from tx_queue_head structure, which is searched for all remaining services and while service is removed, then service questions/asnwers are also removed from this structure. This update fixes possible crash when packet is pushed to action queue, and when service is removed, its answers are removed from tx_queue_head, but not from action queue. this could lead to a crash when the packet is poped from action queue containing questions/answers to already removed (freed) service
Closes IDF-438
mdns_search_once_t::lock is used to synchronize tasks (taken by one
task and given by the other) so it should not be a mutex.
Convert to semaphore, and rename to indicate its purpose.
By default, if a URI handler changes the http session context,
the webserver internally clears the older context after the handler
returns. However, if applications want to change this behavior and
manage the allocation/de-allocation/freeing themselves and let the
server handle only the "socket close" case, this commit provides such
an option.
When xPortGetCoreID() is called twice within a function,
it might only be called once after compilation. This
commit makes the inline assembly of the function volatile.
Closes#3093
Previously when HashList was removing items, HashListBlocks were
removed lazily. This resulted in empty HashListBlocks dangling around
in full pages, even when all items have been erased. These blocks
would only be deleted when NVS was re-initialized
(nvs_flash_deinit/nvs_flash_init).
This change does eager cleanup instead, based on the code from
@negativekelvin offered in
https://github.com/espressif/esp-idf/issues/1642#issuecomment-367227994.
Closes https://github.com/espressif/esp-idf/issues/1642.
1. ref_clock used in unit tests occasionally produces time off by ~100
microseconds shortly after being started. Add a delay to let
ref_clock stabilise, until the cause is found.
2. Reduce roundoff error accumulation which would occasionally cause
the test to fail, by choosing an overflow value which can be divided
by APB frequency.
3. Move time sampling part of the test into an IRAM function to
reduce variations due to cache behavior.
4. Remove calculation of "standard deviation" in the test, as what was
calculated was not actually standard deviation, and it did not add any
useful information.
1. call esp_timer_get_time and ref_clock_get in the same order on
start and in the loop
2. disable interrupts when calculating delta between ref_clock
and esp_timer
3. ensure both functions are in cache before calculating the delta
In the situation when bootloader was compiled for 240MHz, and app was
compiled for 160MHz, and the chip is a revision 0 chip, the
bootloader will assume that the application has also been running at
240MHz. This will cause the chip to lock up later. Modify this to use
a run time check of DPORT_CPUPERIOD_SEL, which indicates which of the
PLL frequencies was used.
Closes https://github.com/espressif/esp-idf/issues/2731.
Previously, this compiler flag was not being applied
regardless of CONFIG_SPIRAM_CACHE_WORKAROUND setting.
Explanation: add_compile_options() only applies to
source files added after the function is run, or in
subdirectories added after the function is run. In
this case, no new source files were being added after
this function was run.
1. Add missing get function to RMT API: rmt_get_idle_level().
2. Suppress error message from rmt_wait_tx_done() if wait_time==0 (allows for polling).
3. Remove the blank lines between parameter lists.
Merges https://github.com/espressif/esp-idf/pull/2666
fix 3 bugs:
1. do BLE connect (both of slave and master), it mgiht cause crash due to there's much interrupts happens effect ble code running, for example, wifi run on the same core as bluetooth controller and wifi run throughtput test.
2. do BLE scan stop or adv stop or connection stop, it might cause ASSERT or crash due to memory corrupted in controller memory poll.
3. minor bug fix, not really effect bluetooth.
when running a query for a single txt, result entries were not created and attached to result structure. this issue was introduced when fixing memory leak in txt structure, which worked correctly for PTR queries, but caused trouble for TXT query.
