1. fix the bug block scan tiemout before scan finish
2. make menuconfig can set the WiFi mgmt short buffer num
3. modify wifi reason code
4. fix the bug PMK recal too long
1. ref_clock used in unit tests occasionally produces time off by ~100
microseconds shortly after being started. Add a delay to let
ref_clock stabilise, until the cause is found.
2. Reduce roundoff error accumulation which would occasionally cause
the test to fail, by choosing an overflow value which can be divided
by APB frequency.
3. Move time sampling part of the test into an IRAM function to
reduce variations due to cache behavior.
4. Remove calculation of "standard deviation" in the test, as what was
calculated was not actually standard deviation, and it did not add any
useful information.
1. call esp_timer_get_time and ref_clock_get in the same order on
start and in the loop
2. disable interrupts when calculating delta between ref_clock
and esp_timer
3. ensure both functions are in cache before calculating the delta
Previously, this compiler flag was not being applied
regardless of CONFIG_SPIRAM_CACHE_WORKAROUND setting.
Explanation: add_compile_options() only applies to
source files added after the function is run, or in
subdirectories added after the function is run. In
this case, no new source files were being added after
this function was run.
The bug will cause memory corrupted (the largest range is from 0x3ffc0000 ~ 0x3ffc8000),
some strange error will happen, like IllegalInstruction, LoadProhibited and .etc.
1. esp32-pico use standard spi driver to access psram
2. for esp32-pico, flash and psram share the clock
3. for esp32-pico, psram cs io can be overwrite via menuconfig
1. Use BIT[7:5] of EID to determine psram size
2. Add ID support for 16Mbit psram
3. Remove module reset on SPI1
4. Confirmed with the vendor that only the old 32Mbit psram need special clock timing. For other psram chips, we should use standard QPI mode.
Files where stack protector is initialized should not be compiled with
stack protector enabled. This was done for Make but missing for CMake.
Fixes https://github.com/espressif/esp-idf/issues/2990.
Fix following WiFi bugs:
1. Fix a crash bug which is caused by WiFi static TX buffer alloc/free.
2. Fix the bug that iphone fails to connect to ESP32 AP by enabling AP BAR receiving.
3. Fix the bug that ESP32 station fails to connect some APs, such as Xiaomi hotspot etc,
after reset.
This commit adds the ability for backtracing to trace from the itnerrupt to the
task stack, and across nested interrupts. Test cases have also been added.
See MR !4084
1. fix network channel switch function.
2. support not configuring the network channel.
3. support not configuring the router BSSID even if the router is hidden.
4. add allow_channel_switch to mesh configuration.
5. add allow_router_switch to mesh router configuration.
6. support handling beacon without IE of DS Parameter Set.
7. fix Wi-Fi RX fails in a specific scenario (update libphy.a).
8. fix STAs can not detect disconnection from AP when encrypt transmission is used.
9. fix can not find hidden APs.
10. for root, modify the active scan time to 120ms.
11. remove all rc when clear parent Wi-Fi configuration.
12. fix memory leak caused by the remove announcement being sent is not released when esp_mesh_stop() is called.
13. fix modify IE encrypt after mesh is started.
14. ignore esp_mesh_connect() if mesh automatic reconnection is enabled.
15. fix reason is cleared before vote is done.
16. fix issues in the example of manual_networking when mesh network is encrypted.
17. detect and fix root conflicts when router BSSID is not set.
18. when root can not connect to the router due to NO_MORE_STAS(reason code:5), root will stop re-connection and perform MESH_NWK_LOOK_FOR_NETWORK.
19. wifi: fix the disconnection caused by receiving a deauth frame from non-parent node during scanning.
20. fix routing table redundant issue due to the remove announcement is not 100% reliable.
21. modify the max routes limitation from 300 to 1000.
22. wifi: fix ap does not deauth the sta which has not yet completed the 4-way handshake but the max replay count is reached.
Previously, hardware SHA engine "locks" were mutex semaphores. This meant that the task which
started a particular SHA session (in hardware) needed to finalise that session, or an invalid
FreeRTOS state was created.
Replace with binary semaphore which can be shared between tasks.
Includes a unit test, but unit test doesn't crash even without this fix
(some other unknown condition is required).
