The under the error condition of rx buffer size is <=128 an error log is printed that reads uart rx buffer length error(>128). Propose an update to better describe the error condition as uart rx buffer length error(<=128).
Signed-off-by: Wu Bo Wen <wubowen@espressif.com>
Merges https://github.com/espressif/esp-idf/pull/5523
On ESP32, due to fifo reset issue, UART2 will work incorrectly if reset the fifo of UART1(TX fifo and RX fifo). The software can workaround the RX fifo reset issue,
while the TX fifo reset issue can not. When UART2 is used and UART1 is used as the log output port, a software reset can reproduce this issue. So we should reset the UART memory
before the software reset to solve this problem.
check master read write functions with array of registers)
fix master serial processing code and modbus controller to work with register array
modbus_master: add reading and writing of test value array (58 registers) to check failure is gone
remove parameter temporary buffer from modbus controller to allow more than 24 byte writes
driver: fix issue with TOUT feature
driver: fix uart_rx_timeout issue
driver: fix issue with rxfifo_tout_int_raw not triggered when received fifo_len = 120 byte and all bytes read out of fifo as result of rxfifo_full_int_raw
driver: add function uart_internal_set_always_rx_timeout() to always handle tout interrupt
examples: call uart_internal_set_always_rx_timeout() to handle tout interrupt correctly
examples: update examples to use tout feature
driver: reflect changes of uart_set_always_rx_timeout() function, change uart.c
driver: change conditions to trigger workaround for tout feature in uart.c
driver: change uart_set_always_rx_timeout()
freemodbus: fix tabs, remove commented code
driver: remove uart_ll_is_rx_idle()
tout_thr - move calculation and masking into hal layer update driver and uart_ll (add uart_ll_set_rx_tout)
move tout calculation into uart_ll
move calculation of time out in bit time for esp32s2 into low level uart_ll.h file
move uart_hal_get_symb_len() into hal
update set_rx_timeout() to warn user about incorrect value
update HAL, LL 1
fix uart_xx_set_rx_tout() to convert symbol time into bit time
update param description
update tout calculation in LL
update uart_hal_get_max_rx_timeout_thrd() and uart_ll_get_max_rx_timeout_thrd()
1. uart_wait_tx_done works incorrect when sending a byte of data.
2. uart_set_rx_timeout sets an incorrect rx timeout value when ref_tick is enabled
closes https://github.com/espressif/esp-idf/issues/3631
Using xxx_periph.h in whole IDF instead of xxx_reg.h, xxx_struct.h, xxx_channel.h ... .
Cleaned up header files from unnecessary headers (releated to soc/... headers).
An existing UART driver does not support RS485 half duplex mode.
This task adds this functionality to ESP_IDF UART driver.
driver/uart.c/h: updated to add support of RS485 half duplex mode
examples/peripherals/uart_echo_rs485/main/rs485_example.c: added test example
components/driver/test/test_uart.c: added test of RS485 half duplex mode
docs/en/api-reference/peripherals/uart.rst: updated documentation
test_uart.c: suppress GCC warnings about discarded const qualifiers
uart.rst: remove sphinx warning - "Duplicate explicit target name"
simple change in uart.h file
update (test_uart.c) after rebase from master
update uart.rst, uart.c, rs485_example.c
Update example description in file Readme.md
update uart.c/h, uart.rst, test_uart.c according to review results
update uart.h (uart_set_rx_timeout() description
test_uart.c remove ignore tag
uart.c/h: fix param errors
test_uart.c: Remove GCC warning supress
uart.rst: fix the notes
rs485_example.c: fix output
uart.c: remove reset using UART_RXFIFO_RST from driver.
readme.md: Update example description
The tests are completed using RS485 adapters hardware connected to two ESP32 WROVER KITs.
TW#13812
Closes https://github.com/espressif/esp-idf/pull/667
Closes https://github.com/espressif/esp-idf/pull/1006
An existing UART driver does not support RS485 half duplex mode.
This task adds this functionality to ESP_IDF UART driver.
driver/uart.c/h: updated to add support of RS485 half duplex mode
examples/peripherals/uart_echo_rs485/main/rs485_example.c: added test example
components/driver/test/test_uart.c: added test of RS485 half duplex mode
docs/en/api-reference/peripherals/uart.rst: updated documentation
test_uart.c: suppress GCC warnings about discarded const qualifiers
uart.rst: remove sphinx warning - "Duplicate explicit target name"
simple change in uart.h file
update (test_uart.c) after rebase from master
update uart.rst, uart.c, rs485_example.c
Update example description in file Readme.md
update uart.c/h, uart.rst, test_uart.c according to review results
update uart.h (uart_set_rx_timeout() description
test_uart.c remove ignore tag
uart.c/h: fix param errors
test_uart.c: Remove GCC warning supress
uart.rst: fix the notes
rs485_example.c: fix output
The tests are completed using RS485 adapters hardware connected to two ESP32 WROVER KITs.
TW#13812
Closes https://github.com/espressif/esp-idf/pull/667
Closes https://github.com/espressif/esp-idf/pull/1006
