1. fix failture of mesh stop caused by block-sending.
2. fix when FIXED_ROOT is set, 2nd layer devices can not receive mesh event ESP_ERR_MESH_NO_PARENT_FOUND.
3. fix when FIXED_ROOT is set and the root turns off mesh function, 2nd layer devices do not look for new parents.
4. add APIs esp_mesh_disconnect() and esp_mesh_connect().
5. disconnect from parent/router when the DSSS channel in received beacon is different from the home channel.
6. remove nvs task to release 3k bytes memory.
Having two different spinlocks is problematic due to possibly
different order in which the locks will be taken. Changing the order
would require significant restructuring of kernel code which is
undesirable.
An additional place where taking xTickCountMutex was needed was in
vApplicationSleep function. Not taking xTickCountMutex resulted in
other CPU sometimes possibly advancing tick count while light sleep
entry/exit was happening. Taking xTickCountMutex in addition to
xTaskQueueMutex has shown a problem that in different code paths,
these two spinlocks could be taken in different order, leading to
(unlikely, but possible) deadlocks.
When light sleep is finished on one CPU, it is possible that the other
CPU will enter light sleep again very soon, before interrupts on the
first CPU get a chance to run. To avoid such situation, set a flag
for the other CPU to skip light sleep attempt.
Tickless idle/light sleep procedure had a bug in single core mode.
Consider the flow of events:
1. Idle task runs and calls vApplicationIdleHook
2. This calls esp_vApplicationIdleHook, which calls esp_pm_impl_idle_hook, and pm lock for RTOS on the current core is released.
3. Then esp_vApplicationIdleHook calls esp_pm_impl_waiti, which checks that s_entered_light_sleep[core_id]==false and goes into waiti state.
4. Some interrupt happens, calls esp_pm_impl_isr_hook, which takes pm lock for RTOS. PM state goes back to CPU_FREQ_MAX.
5. Once the interrupt is over, vApplicationIdleHook returns, and Idle task continues to run, finally reaching the call to vApplicationSleep.
6. vApplicationSleep does not enter light sleep, because esp_pm_impl_isr_hook has already changed PM state from IDLE to CPU_FREQ_MAX.
This didn’t happen in dual core mode, because waiti state of one CPU was interrupted by CCOMPARE update interrupt from the other CPU, in which case PM lock for FreeRTOS was not taken.
Fix by inverting the meaning of the flag (for convenience) and only setting it to true when vApplicationSleep actually fails to enter light sleep.
1. Fix the bug that disable controller suddenly cause crash when ble is working.
2. Fix the bug that when disable controller, it will cause wifi cannot RX, TX timeout, buffer lack and etc.
1. If L2_TO_L3_RX_BUF_MODE is not selected, we must assign l2_owner explictly before we call pbuf_free.
2. free intr resource in esp_eth_deinit
Closes https://github.com/espressif/esp-idf/issues/2670
1. Original register mapping for LAN8720 has some registers that doesn't exist/support.
So just remove them, and fix the power and init function for LAN8720.
2. GPIO16 and GPIO17 is occupied by PSRAM, so only ETH_CLOCK_GPIO_IN mode is supported in that case if using PSRAM.
3. Fix bug of OTA failing with Ethernet
4. Fix bug of multicast with Ethernet
5. Fix potential memory leak
mdns queries did not work properly when send imeadiately after set_hostname, which cuased reinit of pcb and therefore restarted probing, so search packets were blocked until probing finished
closes#2507, closes#2593
1. fix ap_loss that occurs when the parent turns off the mesh function and becomes a normal WiFi with a different SSID.
2. add an event MESH_EVENT_NETWORK_STATE that contains information about whether there is a root in the current network.
3. modify the mechanism of mesh IE update.
4. fix a problem in the process of re-voting to select the root, the device that does not meet the conditions of being a root votes for itself.
5. fix an issue that occurs in esp_mesh_recv_toDS() when stopping the mesh.
6. when the user specifies a parent for the device, the device will set the authmode and password of its AP mode to the same value as the specified parent.
7. add two disconnected reason codes MESH_REASON_EMPTY_PASSWORD and MESH_REASON_PARENT_UNENCRYPTED.
This commit resolves a blocking in esp_aes_block function.
Introduce:
The problem was in the fact that AES is switched off at the moment when he should give out the processed data. But because of the disabled, the operation can not be completed successfully, there is an infinite hang. The reason for this behavior is that the registers for controlling the inclusion of AES, SHA, MPI have shared registers and they were not protected from sharing.
Fix some related issue with shared using of AES SHA RSA accelerators.
Closes: https://github.com/espressif/esp-idf/issues/2295#issuecomment-432898137
