This commit updates how the USBH handles device creation and enumeration so that
upper layers (such as the Hub driver) can use the USBH API for enumeration instead
of calling the HCD.
USBH Updates:
USBH now creates unenumerated devices set to address 0 with no device/config
descriptor. A newly created device can be opened and communicated with immediately
(using control transfers). This allows the Hub driver to call the USBH instead of
the HCD. Summary of USBH changes:
- Added new APIs to add/remove a device. Devices are now created as unenumerated
and can be immediately opened and communicated with.
- Added new APIs to enumerate a device (see 'usbh_dev_set_...()' functions). Device
must be locked (see 'usbh_dev_enum_lock()') before enumeration functions can be called.
- Added UID for each device. This allows the particular USBH without needing to
use the device's handle (which implies opening the device).
Hub Driver Updates:
Hub driver now calls the USBH for enumeration. Summary of USBH changes:
- Replace all 'hcd_pipe_...()' calls with 'usbh_dev_...()' calls
- Refactored port event handling to fit with new USBH API
- Updated to use UID to uniquely identify devices without opening them
USB Host Updates:
- Reroute USBH control transfers to clients and hub driver
This commit updates the HCD API to allow port resets to occur even if pipes
are allocated. The pipes cannot be active and the port reset will simply
restore the pipes (by reinitializing their channel registers) following the
reset.
Changes:
- Allow port resets while channels are allocated
- Remove pipe persistance API 'hcd_pipe_set_persist_reset()'
Previously, on a device disconnection, the USBH and Hub would the require the
following 2-way interaction:
- Hub -> usbh_hub_pass_event() -> USBH to indicate a port error
- USBH -> usbh_hub_req_cb_t -> Hub to request port recovery after the device
has been freed.
The 2-way interaction has been simplified:
- USBH now nofities upper layers of devices being freed via the
USBH_EVENT_DEV_FREE event
- Hub now handles port recovery only after a device has been freed
- user callback funciton to set device configuration
as a part of usb_host_install
- callback provides device descriptor of a device being enumerated
- user can set which cfg descriptor the USB device will be set with
- user can filter device enumeration
- Kconfig menu to enable callback function
- usb_host_lib example demonstration
This commit removes the ability to reserve a header in the data buffer of an
allocated URB. The header was required for a now defunct implementation of a
synchronous USB Host library API. Thus, headers are no longer required in
URB data buffers.
Some devices return full LANGID table, even if short LANGID table was requested.
No memory overflow occurs, because we have allocated enough memory for transfers to the
default pipe. So we can ignore the error and continue with string desc fetching.
This commit refactors the USBH and the USB Host Library in the following ways:
- USBH now presents an abstraction of an endpoint (via usbh_ep_handle_t)
- Added separate functions to enqueue/dequeue URBs to a particular endpoint
- USB Host Library no longer calls HCD API directly. Calls USBH endpoint API
instead.
- Renamed "notif_cb" to "proc_req_cb" (Processing Request Callback)
- This is to avoid confusion with FreerTOS task notifications and Host
Library client event notifications.
- The processing functions of each layer (i.e., "xxx_process()") request
calls via the "proc_req_cb"
- The main handling function (i.e., usb_host_lib_handle_events()) is
responsible for calling the required "xxx_process()" of each layer
When a USB does not support a particular string dsecriptor (e.g.,
manufacturer, product, and serial number), the string descriptors corresponding
index will be set to 0 in the device descriptor (e.g., iManufacturer, iProduct,
iString).
Previously, the Hub driver would always attempt to fetch the all three string
descriptors, thus leading an error in CHECK_SHORT_SER_STR_DESC if the device
did not support the descriptor.
This commit fixes the Hub drvier by skipping the enumeration stages of a
particular descriptor if its index is 0 (i.e., not supported by the device).
USB devices may support string descriptors in multiple languages. The supported
languages are stored in a LANGID table, which itself is a string descriptor at
index 0.
When fetching the LANGID table itself, the USB 2.0 specification does not
specify what LANGID to use, thus the Hub driver would use the default LANGID
"ENUM_LANGID". However, this would cause some devices to stall.
This commit fixes the issue by always requesting the LANGID table itself using
a LANGID of 0.
This commit updates the Hub Driver and USBH as follows:
- Updated communication mechanism between Hub Driver and USBH
- USBH notifies the Hub Driver via Hub request callback (usbh_hub_req_cb_t)
- Hub Driver notifies the USBH via usbh_hub_pass_event()
- Hub Driver now defers all event handling to hub_process.
- Hub Driver and USBH will now automatically recover the port after a disconnected
device has been closed.
- Fixed incorrect assert in usbh_dev_close()
Hub Driver is refactored as follows:
This commit update and refactors the Hub Driver as follows:
- Refactored enumeration state machine and stage functions
- Enumeration stage is now incremented
- Combined transfer stages of enumeration into common functions
- Comments updated
- Fixed usbh_hal_disable_debounce_lock() that would cause root_port_handle_events()
to fail the HCD_PORT_CMD_RESET call because the previous port connection interrupt
was not cleared.
The following features were added to the Hub Driver
- Enumeration config descriptor is now fetched in two separate stages
- Header is fetched first to determine the wTotalLength of the descriptor
- Fetching the full descriptor will request exactly wTotalLength bytes
- This works around some non-compliant devices that will babble/return zero
when requesting a length > wTotalLength
- Closes https://github.com/espressif/esp-idf/issues/7799
- Enumeration now stores string descriptors
- The Manufacturer, Product, and Serial Number string descriptors are
now read and stored during enumeration
- String descriptors are now part of usb_device_info_t
- Added unit test to test enumeration
This commit adds the preliminary version of the USB Host Library. This commit contains:
- USBH (USB Host Driver)
- Hub Driver that only supports a single device and device enumeration
- USB Host Library (asychronous API)
- Test cases for USB Host Library asychronous API
The following changes were made to the existing HCD:
- Removed HCD_PIPE_STATE_INVALID. Pipes are no longer invalidated
- Changed pipe commands to halt, flush, and clear. Pipes need to be manually
halted, flush, and cleared.
- Halting and flushing a pipe will execute the pipe callback if it causes a
HCD_PIPE_EVENT_URB_DONE event
