ledc_ls_timer_update is required only when CLK_DIV and DUTY_RES bits are changed.
Calling ledc_timer_rst while re-configure PWM frequency through ledc_set_freq can cause glitch in the signal
esp_light_sleep_start() will stall the other CPU via esp_ipc_isr_stall_other_cpu(). After stalling the other CPU,
will call esp_clk_... API which themselves take locks. If the other stalled CPU is holding those locks, this will
result in a deadlock.
This commit adds a workaround calling esp_clk_private_lock() to take the lock before stalling the other CPU.
esp_clk used to be protected using _lock_t (i.e., a FreeRTOS Mutex). However, esp_clk API is current called from
from critical sections, thus mutex should not be used (as they can be blocking).
This commit updates esp_clk to use spinlocks for critical sections instead.
Note: Added a small fix to exclude esp_clk.c from bootloader builds in the
legacy build system (this is already the case in CMake).
define: lock_bits = (lock->status & LOCK_MASK) >> LOCK_SHIFT; This `lock_bits` is the Bit 29-20 of the lock->status
1. spi_hdl_1:
acquire_end_core():
uint32_t status = lock_status_clear(lock, dev_handle->mask & LOCK_MASK);
Becuase this is the first `spi_hdl_1`, so after this , lock_bits == 0`b0. status == 0
2. spi_hdl_2:
acquire_core:
uint32_t status = lock_status_fetch_set(lock, dev_handle->mask & LOCK_MASK);
Then here status is 0`b0, but lock_bits == 0`b10. Because this is the `spi_hdl_2`
3. spi_hdl_2:
`acquire_core` return true, because status == 0. `spi_bus_lock_acquire_start(spi_hdl_2)` then won't block.
4. spi_hdl_2:
spi_device_polling_end(spi_hdl_2).
5. spi_hdl_1:
acquire_end_core:
status is 0, so it cleas the lock->acquiring_dev
6. spi_hdl_2:
spi_device_polling_end:
assert(handle == get_acquiring_dev(host)); Fail
Closes https://github.com/espressif/esp-idf/issues/8179
update gpio_sig at `spics_out` array in each spi_periph.c of chips later than s2
then `spi_bus_add_device` can correctly distribute gpio_signals for cs_signal
Closes https://github.com/espressif/esp-idf/issues/8876
`__COMPONENT_TARGETS` is evaluated very early when components and
component directories are added to the build, which means that all
components (including the ones which are in EXCLUDE_COMPONENTS) have
a build system target defined. The component manager was given the
list of all known components (derived from the list of targets), not
the list of components after EXCLUDE_COMPONENTS were processed.
Because of that, EXCLUDE_COMPONENTS didn't effectively exclude the
component from the consideration of the component manager.
Due to unit test, we can't specify runners, for adc related tests.
Whereas adc tests are easily influenced by board hw condition, e.g.
pullup/down value.
This commit increases the thresh to 200mV.
dl.espressif.com is now using the same root certificate as github.com.
This commit replaces the previously-used ISRG X1 root certificate
with the DigiCert Root CA certificate.
As a result, even if the certificates are not installed (as it happens
on macOS with python.org installers, if the user forgets to run
'Install Certificates.command'), the download is successful.
Related to https://github.com/espressif/esp-idf/issues/4081
