Allow separate ethernet & wifi configuration
If only 1/2 of ethernet & WiFi are enabled in config, the other interface is no longer linked into the firmware.
* Fixes bug where enabling Ethernet but not WiFi would fail to compile.
* Also means that enabling WiFi but not Ethernet no longer links some unused ethernet interface functions.
See merge request !525
Feature/add user set mac
1. Add menuconfig for user to set mac address of wifi, bt and ethernet.
2. Add the number of MAC address generated from efuse for user to choose.
3. Add MAC address derive method.
See merge request !542
1. RTC V214: modify APLL function for the chip of ECO version.
2. Add API phy_close_rf() and use it in esp_phy_deinit() instead of pm_close_rf().
3. RTC V213: fix BT will not work when BT-init is called more than once.
Optimize or release memory in bluetooth
1. add option to release about 30K from BT if BLE only
2. later BT/BLE will be separated by BT/BLE macro, but this option should use when user make sure that in BLE only mode.
See merge request !520
In case WiFi/BT stack has been enabled but wasn’t disabled, some RTC
bits may be left enabled, causing increased current consumption.
This change returns some of the bits back to their default values.
1. add new APIs bt controller enable/disab/deinit
2. make bt controller work need to call two APIs of esp_bt_controller_init and enable
3. modify phy init to make mac reset once
1. add a macro in menuconfig for users to choose whether store phy calibration data into NVS or not.
2. rename some disable phy and rf APIs so that existing code which calls old APIS will fail to compile.
1. Add disable PHY and RF when WiFi and BT are both disabled(including call sniffer disable API).
2. Do not init PHY and RF when cpu start. Init PHY and RF when call Wifi or BT start APIs(including sniffer enable API).
3. Add a temporary lib: librtc_clk.a and will delete it when CPU frequency switching function is done.
4. Add an function to get OS tick rate.
5. Do not put the whole pp.a in iram0, only put lmac.o, ieee80211_misc.o, ets_time.o and wdev.o in iram0.
phy_init: don’t rewrite valid calibration data
In the default PHY init routine, calibration data is loaded from NVS.
Most of the time the incremental changes to calibration will be fairly
small, so we don’t need to rewrite the existing calibration data stored
in the NVS.
Possible enhancement to be done in the future: expose a function in PHY
library to tell how big was the change in calibration data. If the
change was significant, then calibration data stored in NVS should be
updated.
See merge request !487
1. Reduce the default static rx buffer size from 25 to 10
2. Adjust ampdu interrupt size to 3, namely, raise 1 interrupt per 3-mpdu
3. Make a copy for all received packets, including AMSDU/AMPDU/MPDU
4. Fix softap mis-forward issue
5. Fix pp q full issue
6. Fix sniffer copy wrong content issue
In the default PHY init routine, calibration data is loaded from NVS.
Most of the time the incremental changes to calibration will be fairly
small, so we don’t need to rewrite the existing calibration data stored
in the NVS.
Possible enhancement to be done in the future: expose a function in PHY
library to tell how big was the change in calibration data. If the
change was significant, then calibration data stored in NVS should be
updated.
esp32: Fixes watchdog problem when printing core dump to uart
1) Fixes watchdog problem when printing core dump to uart
2) Also fixes generation of core dumps when flash cache is disabled
See merge request !472
1. fix ampdu<->mpdu<->ampdu switch may cause rx slow issue by put mpdu into ampdu reorder queue
2. fix each ac first sending always fail issue by adding retry
1. modify the discover retry backoff time from (2,4,8,16,32,60,60)s to (500m,1,2,4,8,15,15)s.
2. add DHCP_DOES_ARP_CHECK to menuconfig for users to specify if do a ARP check on the offered address.
If enable, one more second will be taken in obtaining IP address.
3. update wifi libs
Move PHY options out of WiFi config, improve descriptions
- move PHY-related settings into new menu, make it dependent on WIFI_ENABLED || BT_ENABLED
- improve descriptions of Ethernet Kconfig options
See merge request !443
ESP32_PHY_MAX_TX_POWER option is only meaningful for WiFi, so previous
change made it depend on WIFI_ENABLED. However if WiFi is not enabled,
but BT is, this option becomes undefined which breaks phy_init_data
generation.
This change turns ESP32_PHY_MAX_TX_POWER into a hidden parameter, which
depends on PHY_ENABLED. New user-visible parameter,
ESP32_PHY_MAX_WIFI_TX_POWER is introduced which depends on WIFI_ENABLED
and is used as default value for ESP32_PHY_MAX_TX_POWER if WIFI_ENABLED
is set. Otherwise ESP32_PHY_MAX_WIFI_TX_POWER is set to 20.
