esp32: initialize cross-core interrupt in single core mode
The software interrupt originally used as the cross-core interrupt is
now also used to yield from a FreeRTOS critical section; therefore it
must be initialized for single core mode as well.
Fixes https://github.com/espressif/esp-idf/issues/496
See merge request !640
fix warnings generated by ESP_ERROR_CHECK(variable) in release builds
This uses the same pattern as “assert” in release builds to silence the
warning. At the same time, we make sure that if a statement is wrapped
into ESP_ERROR_CHECK, it is executed in release build as well.
Fixes https://github.com/espressif/esp-idf/issues/497
See merge request !641
You can set esp32 as AP/STA, client/sever, sender/recever in menuconfig.
You can set whether to display delay time info in menuconfig.
Now you can transfer data between esp and esp.
This uses the same pattern as “assert” in release builds to silence the
warning. At the same time, we make sure that if a statement is wrapped
into ESP_ERROR_CHECK, it is executed in release build as well.
The software interrupt originally used as the cross-core interrupt is
now also used to yield from a FreeRTOS critical section; therefore it
must be initialized for single core mode as well.
Fixes https://github.com/espressif/esp-idf/issues/496
esp32: RWDT is used to reboot system in case of panic handler crash
This branch uses RWDT to reboot system in case of panic handler crash.
See merge request !625
Feature/btdm uart hci
1. support UART HCI, devolper need not to make a bridge between VHCI and UART.
2. fix bug of rand/srand called in ISR.
3. fix bug of BLE rx packets may cause assert.
See merge request !626
component/bt : modify alarm APIs to be safely accessible from multiple tasks
Improve the osi_alarm module to make the alarm APIs become thread safe.
See merge request !570
1. support UART HCI, devolper need not to make a bridge between VHCI and UART.
2. fix bug of rand/srand called in ISR.
3. fix bug of BLE rx packets may cause assert.
lwip: implement lwip critical session with mutex
Currently lwip critical session is based on interrupt, now replace it with mutex
See merge request !595
spi_flash: fix race condition in s_flash_op_complete access
Flash operation complete flag was cleared by the CPU initiating flash operation. If the other core was running an ISR, then IPC task could be late to enter the loop to check `s_flash_op_complete` by the time next flash operation started. This would cause a deadlock, as the IPC task would still be waiting for `s_flash_op_complete` to be set (which was already cleared by the next flash operation), while the flash operation task would be blocked waiting for IPC task to set `s_flash_op_can_start`.
If the flag is cleared on the CPU waiting on this flag, then the race condition can not happen.
See merge request !615
Fix timing adjustment needed for higher speeds of SPI master bus.
Ref https://github.com/espressif/esp-idf/issues/363 . It was found out the master SPI driver didn't exactly calculate the delay compensation needed, breaking 20 and 26MHz full-duplex mode. This fixes these use cases. We also found out 40MHz full-duplex routed over the GPIO matrix does not work because of a hardware quirk; this MR adds a check/error for that case until we find a workaround.
See merge request !547
Add WiFi static and dynamic tx buffer choice
If static tx buffer is selected, WiFi tx buffers are allocated when WiFi is initialized and released
when WiFi is de-initialized. If dynamic tx buffer is selected, WiFi tx buffer is allocated when tx
data is delivered from LWIP to WiFi and released when tx data is sent out by WiFi.
The size of each static tx buffers is fixed to about 1.6KB and the size of dynamic tx buffers is
depend on the length of the data delivered from LWIP.
If PSRAM is enabled, "STATIC" should be selected to guarantee enough WiFi tx buffers.
If PSRAM is disabled, "DYNAMIC" should be selected to improve the utilization of RAM.
See merge request !580
If static tx buffer is selected, WiFi tx buffers are allocated when WiFi is initialized and released
when WiFi is de-initialized. If dynamic tx buffer is selected, WiFi tx buffer is allocated when tx
data is delivered from LWIP to WiFi and released when tx data is sent out by WiFi.
The size of each static tx buffers is fixed to about 1.6KB and the size of dynamic tx buffers is
depend on the length of the data delivered from LWIP.
If PSRAM is enabled, "STATIC" should be selected to guarantee enough WiFi tx buffers.
If PSRAM is disabled, "DYNAMIC" should be selected to improve the utilization of RAM.
