Originally, when doing BLE active scan, Bluedroid will not report adv to
application layer until receive scan response. This option is used to
disable the behavior. When enable this option, Bluedroid will report
adv data or scan response to application layer immediately.
1. start an esp_timer on entering sleep to acquire pm_lock before wake up from modem sleep
2. decrease the clock division of XTAL fed to bluetooth low power clock from 32us to 2us period to allow to work under 240MHz Max CPU frequency
3. decrease the minimum sleep duration threshold to allow shorter bluetooth modem sleep period, especially for BLE with short connection interval
4. reconfigure bluetooth baseband(BT-BB) settings after PHY/RF init upon waking up from modem sleep to avoid packet RX/TX performance degradation
Earlier they have to be selected at the compile time through sdkconfig.
A2DP sink and source application tested with this change.
Signed-off-by: Amey Inamdar <amey@espressif.com>
1. provide options for bluetooth low power mode
2. provide two options for bluetooth low power clock: main XTAL and external 32kHz XTAL
3. provide function and callbacks to control bluetooth low power mode, including enable/disable sleep, software wakeup request, low power clock settings, check power state, etc
4. modify vhci API vhci_host_send_packet to use blocking mode
5. note that DFS and bluetooth modem sleep can not be used together currently.
As of now, when Bluetooth debugs are enabled, all the messages are
mapped to BT_PRINTF which is mapped to ESP_LOGE. Hence, make monitor
shows all logs in red color which might lead to missing the actual
errors
This patch maps the Bluetooth messages to appropriate ESP_LOG* messages
and improves readability.
Also, make the BT trace level be configurable in menuconfig, so that
each layer of bt trace can be enabled/disabled.
Finally, add debug log control for BTC, OSI, BLUFI and clear up
Bluetooth debug logs.
So, with this the method of enabling Bluetooth logs is as follows:
1. make menuconfig -> Component config -> Bluetooth -> Bluedroid Enable
-> BT DEBUG LOG LEVEL -> set trace level for every layer of BT
Signed-off-by: Hrishikesh Dhayagude <hrishi@espressif.com>
component/bt: Added the Macro for the classic BT support.
component/bt: added the bluedroid deinit method.
component/bt: allow more classic BT global variables to use dynamic allocation scheme
1. allocate memory for AVDT, AVCT control blocks when dynamic memory is used
2. allow SBC decoder buffer to use dynamic allocation scheme
component/bt: Remove the wrong changes in bt/Kconfig & Added the GATTS_INCLUDED in the gatt_free function when gatt service close.
component/bt: Shorten the abbreviation BT_ALLOCATION_FROM_SPIRAM_FIRST and BT_BLE_DYNAMIC_ENV_MEMORY two macros.
1. add sw interrupt cause osi to controller.
2. modify the kconfig to improve the option view.
3. add option of the cpu core which bluedroid run.
4. add option of the cpu core which bluetooth controller run.
1. For now, some security related functions used in classic Bluetooth are controlled by "SMP_ENABLE". This commit fixes the dependency.
2. The two options, "CLASSIC_BT_ENABLED" and "SMP_ENABLED" The two options will be decoupled in the future.
1.change the rowdata to rodata;
2.change BT_ACL_CONNECTIONS to Maximum BT/BLE connection count.
3. change the comments of bt_target.h:505 from 40 to 5.
1. support UART HCI, devolper need not to make a bridge between VHCI and UART.
2. fix bug of rand/srand called in ISR.
3. fix bug of BLE rx packets may cause assert.
1. fix the exception of deinit/disable
2. debug mem leak of deinit, fix some memleak, but still something wrong.
3. debug men leak of disable.
4. add bluedroid memory debug
