The psram cache bug fix was also being applied to the bootloader binary (for cmake),
which doesnt do any psram access.
Applying this fix would increase the binary size, as much as 300 bytes in worst case scenarios
The CPU might prefetch instructions, which means it in some cases
will try to fetch instruction located after the last instruction in
flash.text.
Add dummy bytes to ensure fetching these wont result in an error,
e.g. MMU exceptions
Additionally, always enable the partition MD5 check if flash encryption is on in
Release mode. This ensures the partition table ciphertext has not been modified
(CVE-2021-27926).
The exception is pre-V3.1 ESP-IDF bootloaders and partition tables, which
don't have support for the MD5 entry.
Since dd849ffc, _rodata_start label has been moved to a different
linker output section from where the TLS templates (.tdata, .tbss)
are located. Since link-time addresses of thread-local variables are
calculated relative to the section start address, this resulted in
incorrect calculation of THREADPTR/$tp registers.
Fix by introducing new linker label, _flash_rodata_start, which points
to the .flash.rodata output section where TLS variables are located,
and use it when calculating THREADPTR/$tp.
Also remove the hardcoded rodata section alignment for Xtensa targets.
Alignment of rodata can be affected by the user application, which is
the issue dd849ffc was fixing. To accommodate any possible alignment,
save it in a linker label (_flash_rodata_align) and then use when
calculating THREADPTR. Note that this is not required on RISC-V, since
this target doesn't use TPOFF.
Fixes issue with DPORT init task, this task uses minimum stack size and may not be
enough if stack smashing detection is set to Overall mode.
Also reworks the way we calculate minimum stack to allow for adding multiple
contributing factors.
Closes https://github.com/espressif/esp-idf/issues/6403
On S2 the brown out detector would occasionally trigger erroneously during deep sleep.
Disable it before sleeping to circumvent this issue.
Closes https://github.com/espressif/esp-idf/issues/6179
Sometimes the flash size read from bootloader is not correct. This may
forbid SPI Flash driver from reading the the area larger than the size
in bootloader header.
When the new config option is enabled, the latest configured
ESPTOOLPY_FLAHSIZE in the app header will be used to override the value
read from bootloader header.
Fix for issues where RTC FAST memory is updated as part of going into deep
sleep. Very high risk if heaps are in RTC memory - in particular task stacks
may be in RTC memory, but also other variables.
Also fixes potential concurrency problems as RTC FAST memory is not accessible
by CPU during the CRC calculation itself.
Method:
- Disable interrupts (currently for single core only, will need update for S3)
- Load all registers before calculating CRC or going to sleep
If esp_restart_noos() is run and the stack address points to external memory (SPIRAM)
then Cache_Read_Disable() raises up the error "Cache disabled but cached memory region accessed"
to fix this we switch stack to internal RAM before disable cache.
Added unit tests.
Closes: https://github.com/espressif/esp-idf/issues/5107
This commit adds TWAI driver support for the
ESP32-S2. The following features were added:
- Expanded BRP support
- Expanded CLKOUT Divider Support
- Updated example READMEs
Allows booting in QIO/QOUT mode or with PSRAM on ESP32-PICO-V3 and
ESP32-PICO-V3-O2 without any config changes.
Custom WP pins (needed for fully custom circuit boards) should still be compatible.
The issue is caused by:
1. The disable_qio_mode inside read_id may have side effects.
2. read_id twice may have side effects.
Fix this issue by moving disable_qio_mode out of read_id and only do it
once before read_id. And retry read_id only when the first one is
failed.
Issue introduced in 3ecbb59c15.
