This solves the issue that target is changed to the default one after
idf.py fullclean.
Also allow setting the default target using sdkconfig.defaults, e.g.
CONFIG_IDF_TARGET="esp32s2"
Closes IDF-1040
implemented workaround in idf_monitor for known usbser.sys bug which
causes changes in RTS signal to only be sent if DTR signal also changes.
Works by forcing a dummy change in DTR signal (re-assigning its current
value, as it has previously been done in the flashing tool)
Closes https://github.com/espressif/esp-idf/pull/4676
These definitions have ended up being chip specific. Moving them into
respective soc_memory_layout.c makes the whole picture of memory
regions easier to see, and also makes adding support for new chips
easier.
-nostdlib was removed in 9a2af7a and then accidentally added
in 1c2cc54.
The issue manifested itself as a failure to link some symbols from
libgcc, even though libgcc should implicitly appear at the end of the
linker command line when -nostdlib is not given.
1. add brownout detector HAL for esp32 and esp32s2
2. enable brownout reset for esp32 rev. 1 and above
3. add approximate brownout detector levels for esp32s2
test_mux register doesn't exist in RTCCNTL anymore, remove it from
struct header. Also remove adc_ll_vref_output implementation, which
depends on that register.
1. Clarify THREADPTR calculation in FreeRTOS code, explaining where
the constant 0x10 offset comes from.
2. On the ESP32-S2, .flash.rodata section had different default
alignment (8 bytes instead of 16), which resulted in different offset
of the TLS sections. Unfortunately I haven’t found a way to query
section alignment from C code, or to use a constant value to define
section alignment in the linker script. The linker scripts are
modified to force a fixed 16 byte alignment for .flash.rodata on the
ESP32 and ESP32-S2beta. Note that the base address of .flash.rodata
was already 16 byte aligned, so this has not changed the actual
memory layout of the application.
Full explanation of the calculation below.
Assume we have the TLS template section base address
(tls_section_vma), the address of a TLS variable in the template
(address), and the final relocation value (offset). The linker
calculates:
offset = address - tls_section_vma + align_up(TCB_SIZE, alignment).
At run time, the TLS section gets copied from _thread_local_start
(in .rodata) to task_thread_local_start. Let’s assume that an address
of a variable in the runtime TLS section is runtime_address.
Access to this address will happen by calculating THREADPTR + offset.
So, by a series of substitutions:
THREADPTR + offset = runtime_address THREADPTR = runtime_address - offset
THREADPTR = runtime_address - (address - tls_section_vma + align_up(TCB_SIZE, alignment)) THREADPTR = (runtime_address - address) + tls_section_vma - align_up(TCB_SIZE, alignment)
The difference between runtime_address and address is same as the
difference between task_thread_local_start and _thread_local_start.
And tls_section_vma is the address of .rodata section, i.e.
_rodata_start. So we arrive to
THREADPTR = task_thread_local_start - _thread_local_start + _rodata_start - align_up(TCB_SIZE, alignment).
The idea with TCB_SIZE being added to the THREADPTR when computing
the relocation was to let the OS save TCB pointer in the TREADPTR
register. The location of the run-time TLS section was assumed to be
immediately after the TCB, aligned to whatever the section alignment
was. However in our case the problem is that the run-time TLS section
is stored not next to the TCB, but at the top of the stack. Plus,
even if it was stored next to the TCB, the size of a FreeRTOS TCB is
not equal to 8 bytes (TCB_SIZE hardcoded in the linker). So we have
to calculate THREADPTR in a slightly obscure way, to compensate for
these differences.
Closes IDF-1239
The NimBLE host buffers that consume a significant amount of memory are
now allocated dynamically.
The advantage is that, the memory can be reclaimed in cases where BLE
is turned off and not required for the current boot cycle
