Optimize or release memory in bluetooth
1. add option to release about 30K from BT if BLE only
2. later BT/BLE will be separated by BT/BLE macro, but this option should use when user make sure that in BLE only mode.
See merge request !520
1. indicate adv/scan start complete success or failed
2. controller do limit of adv/scan concurrence, so add some codes to report adv/scan start failed or not.
The root cause is the bug in bluetooth controller, in which the HCI_SNIFF_MODE command is sent to controller and at the same time the controller has received same request from remote device.
For now change the time-out period of local device to enter the SNIFF mode.
Fix a scheduling bug
Fixes:
- Trivial bug where in some special cases a task could be started on the wrong core (and would run there for max 1 tick)
- More major bug causing a yield to be done with a mux held.
See merge request !523
Fix SPI master transmit length
Tx/Rx length fix from https://github.com/espressif/esp-idf/pull/336
I also added an extra commit in to make use of a define instead of a literal, plus fix a (harmless) off-by-one condition.
See merge request !521
This fixes incorrect descriptions of I_END/I_SLEEP instructions and
changes the definition of I_END. New instruction, I_WAKE, is added,
which wakes up the SoC. Macro for ADC instruction is defined, and new
tests are added.
This change adds esp_deep_sleep_get_wakeup_cause, which returns the
source which has caused wakeup from deep sleep.
Similar to esp_deep_sleep_get_ext1_wakeup_status, a function is added
to check touch pad wakeup status: esp_deep_sleep_get_touchpad_wakeup_status.
This function returns the touch pad which has caused wakeup.
ULP and touch FSMs in ESP32 revisions 0 and 1 do not operate correctly
if RTC_PERIPH power domain is force powered on (ESP_PD_OPTION_ON).
Both ULP and touch still work, but clock frequency of the ULP may be
incorrect and touch values may be off by considerable amount. As such,
when these wakeup modes are used, RTC_PERIPH power domain has to be set
to ESP_PD_OPTION_AUTO (or, in the current implementation,
ESP_PD_OPTION_OFF — though this will change in the future when _OFF will
actually *force* the power domain to be powered off).
Because EXT0 wakeup source requires RTC_PERIPH to be powered ON, mark
ULP and touch wakeup sources as incompatible with EXT0. Workaround for
this is to use EXT1 wakeup source instead, which offers similar or
better functions without having to keep RTC_PERIPH powered on.
- I_RD_REG used the wrong union member (.rd_reg) due to a copy-paste
mistake
- Peripheral register address in bits[7:0] should be given in words,
not in bytes
Fixes https://github.com/espressif/esp-idf/issues/297
Deep sleep fixes
This change fixes extra 24 uA current consumption in deep sleep mode (https://esp32.com/viewtopic.php?f=2&t=1133).
Recent update to libphy/librtc caused another problem that WiFi related parts of RTC are no longer disabled by RTC sleep functions. This means that if WiFi is not disabled by the application before entering deep sleep, extra ~200uA of current would be consumed. This is fixed, and documentation for esp_deep_sleep and SNTP example are updated to mention that applications should take care of disabling WiFi and BT before going into the deep sleep mode.
See merge request !516
spi_flash: fix protection issues
This MR fixes the two spi_flash related issues:
- esp_intr_noniram_{disable,enable} not being protected by spi_flash_op_{lock,unlock} in single core mode. This caused a safety assert to be triggered in esp_intr_noniram_disable.
- spi_flash_unlock not being protected by spi_flash_guard_{start,end}. This caused a conflict between SPI0 and SPI1 controllers when accessing SPI flash, manifesting in cache data corruption and IllegalInstruction exceptions, for some flash chips.
See merge request !522
spi_flash_unlock was missing spi_flash_guard_start, which caused cache
to be enabled during unlock operation, causing hard-to-trace crashes
and cache data corruption.
build system: Fix several make & configuration problems
Collection of quasi-related build system fixes:
* Fix issues with "make menuconfig" running twice when no existing sdkconfig
* Fix issues with menuconfig getting into a bad state if "make -jN" and no existing sdkconfig
* Hopefully fix intermittent issue with build system sometimes not picking up all config, leading to missing BT/WiFi libs at compile/link time.
* Fix issues with path resolution on Windows (including in Eclipse)
* Add new BATCH_BUILD variable for IDEs and automated build environments.
See merge request !485
See github #311https://github.com/espressif/esp-idf/issues/311
Should fix weird compiler/linker bugs where config says something is
enabled, but build system says it is disabled.
Particularly noticeable when WiFi/BT libraries fail to
compile/link despite being enabled.
Underlying cause is configuration file regenerating, but component
Makefiles not reevaluating.
Entirely removes the idea that we don't need to generate config for some
targets (like 'clean'). We need valid config for these targets,
otherwise they don't know which files to clean (etc).
MR !441 (7c155ab) has fixed issue with esp_intr_noniram_{disable,enable}
calls not being properly protected by spi_flash_op_{lock,unlock}.
Unit test was added, but the unit test environment tests only dual-core
config. Similar issue was present in the code path for the single-core
config, where esp_intr_noniram_{disable,enable} calls were unprotected.
This change fixes the protection issue and updates the unit test to
run properly in single core config as well.
The issue with running unit tests for single core config will be
addressed in a separate MR.
In case WiFi/BT stack has been enabled but wasn’t disabled, some RTC
bits may be left enabled, causing increased current consumption.
This change returns some of the bits back to their default values.
