1. add check in the gdma driver, to prevent multiple channels connecting
to the same peripheral
2. memory copy DMA ID will occupy the peripheral's DMA ID on some ESP
targets (e.g. esp32c3/s3). We should search for a free one when
install async memcpy driver.
Closes https://github.com/espressif/esp-idf/issues/10575
When a public header contains _Static_assert or static_assert, check_public_headers.py script will detect it and report it as an issue.
Indeed, public headers shall now use ESP_STATIC_ASSERT.
Fix issue with single bus clear counter but two I2C buses (I2C0, I2C1). The previously implemented single (static) counter would impact the second bus either if one bus has counter expiry.
Merges https://github.com/espressif/esp-idf/pull/7144
In previous transmission(s), the TX_DONE interrupt raw bit may be raised, but never been cleared.
TX_DONE interrrupt status bit should be cleared before enabling it to check the new transmission.
Introduced in 4e09d147b11ed8a094b5858642c9f60d658ef656
Internally, disable usb serial jtag DP pin's pullup when calling gpio_ll_pullup_dis and rtcio_ll_pullup_disable
At usb serial jtag setup/install, re-enable DP pin's pullup
Closes https://github.com/espressif/esp-idf/issues/9495
ledc_ls_timer_update is required only when CLK_DIV and DUTY_RES bits are changed.
Calling ledc_timer_rst while re-configure PWM frequency through ledc_set_freq can cause glitch in the signal
define: lock_bits = (lock->status & LOCK_MASK) >> LOCK_SHIFT; This `lock_bits` is the Bit 29-20 of the lock->status
1. spi_hdl_1:
acquire_end_core():
uint32_t status = lock_status_clear(lock, dev_handle->mask & LOCK_MASK);
Becuase this is the first `spi_hdl_1`, so after this , lock_bits == 0`b0. status == 0
2. spi_hdl_2:
acquire_core:
uint32_t status = lock_status_fetch_set(lock, dev_handle->mask & LOCK_MASK);
Then here status is 0`b0, but lock_bits == 0`b10. Because this is the `spi_hdl_2`
3. spi_hdl_2:
`acquire_core` return true, because status == 0. `spi_bus_lock_acquire_start(spi_hdl_2)` then won't block.
4. spi_hdl_2:
spi_device_polling_end(spi_hdl_2).
5. spi_hdl_1:
acquire_end_core:
status is 0, so it cleas the lock->acquiring_dev
6. spi_hdl_2:
spi_device_polling_end:
assert(handle == get_acquiring_dev(host)); Fail
Closes https://github.com/espressif/esp-idf/issues/8179
Due to unit test, we can't specify runners, for adc related tests.
Whereas adc tests are easily influenced by board hw condition, e.g.
pullup/down value.
This commit increases the thresh to 200mV.
esp-ringbuf funtion placement is now controlled by its own configs:
CONFIG_RINGBUF_PLACE_FUNCTIONS_INTO_FLASH and CONFIG_RINGBUF_PLACE_ISR_FUNCTIONS_INTO_FLASH
Closes https://github.com/espressif/esp-idf/issues/9198
Since cpu retention dma use rc fast as clk source, so rc_fast_digi
will be enabled when we config to pd cpu. And cpu retention does not
need rc fast keep on during light sleep. So, if we use rc_fast_digi
to determine whether rc fast can be powered down, then cpu and and
rc fast cannot pd at the same time.
When working in continuous mode, hardware will continuously trigger
ADC to do conversions. On esp32s2, 2 bytes will be generated per
conversion. Prior to this commit, driver assumes 4 bytes per conversion
(on s2). This commit fixed this issue.
