The WiFi station connect sequence diagram does not have any "successful" ending.
It looks like a copy-paste error, because there are two consequent `SYSTEM_EVENT_STA_DISCONNECTED` events firing with nothing happening in between.
I think the original meaning was that the last event should be `SYSTEM_EVENT_STA_CONNECTED` to signify that if all goes well, that is the event that will be fired.
Merges https://github.com/espressif/esp-idf/pull/2065
Since 94250e42a0, UART output is suspended when entering sleep mode
(deep or light sleep). This makes sense for light sleep, where sleep
normally takes small amount of time, and flushing the UART would add
a lot of latency. But this breaks existing behaviour for deep sleep,
where UART output was previously sent out before entering sleep mode.
Closes https://github.com/espressif/esp-idf/issues/2145
An existing UART driver does not support RS485 half duplex mode.
This task adds this functionality to ESP_IDF UART driver.
driver/uart.c/h: updated to add support of RS485 half duplex mode
examples/peripherals/uart_echo_rs485/main/rs485_example.c: added test example
components/driver/test/test_uart.c: added test of RS485 half duplex mode
docs/en/api-reference/peripherals/uart.rst: updated documentation
test_uart.c: suppress GCC warnings about discarded const qualifiers
uart.rst: remove sphinx warning - "Duplicate explicit target name"
simple change in uart.h file
update (test_uart.c) after rebase from master
update uart.rst, uart.c, rs485_example.c
Update example description in file Readme.md
update uart.c/h, uart.rst, test_uart.c according to review results
update uart.h (uart_set_rx_timeout() description
test_uart.c remove ignore tag
uart.c/h: fix param errors
test_uart.c: Remove GCC warning supress
uart.rst: fix the notes
rs485_example.c: fix output
The tests are completed using RS485 adapters hardware connected to two ESP32 WROVER KITs.
TW#13812
Closes https://github.com/espressif/esp-idf/pull/667
Closes https://github.com/espressif/esp-idf/pull/1006
An existing UART driver does not support RS485 half duplex mode.
This task adds this functionality to ESP_IDF UART driver.
driver/uart.c/h: updated to add support of RS485 half duplex mode
examples/peripherals/uart_echo_rs485/main/rs485_example.c: added test example
components/driver/test/test_uart.c: added test of RS485 half duplex mode
docs/en/api-reference/peripherals/uart.rst: updated documentation
test_uart.c: suppress GCC warnings about discarded const qualifiers
uart.rst: remove sphinx warning - "Duplicate explicit target name"
simple change in uart.h file
update (test_uart.c) after rebase from master
update uart.rst, uart.c, rs485_example.c
Update example description in file Readme.md
update uart.c/h, uart.rst, test_uart.c according to review results
The tests are completed using RS485 adapters hardware connected to two ESP32 WROVER KITs.
TW#13812
Closes https://github.com/espressif/esp-idf/pull/667
Closes https://github.com/espressif/esp-idf/pull/1006
This change allows readonly FATFS to be mounted without wear levelling
support. This will provide the customers a simple way to mount FATFS images
generated on host and flashed onto the chip during factory provisioning.
Since NVS encryption is not supported yet and NVS entry size is limited,
the change will provide an easy alternative for securing the provisioning data
by just marking FATFS parition as encrypted.
The old command caused was incorrect (x is “examine”, not “execute”)
and caused GDB register update only by chance. This replaces it with
“flushregs” command which purpose is exactly that — force GDB to
fetch registers from the remote.
These versions of conf/mconf are forked from the upstream, and the CMake system allows mconf-idf to
be installed externally on the path. So the best option is to rename.
Includes changes to Windows installer for v1.1
Don't show the "Python 2 interpreter" option in menuconfig when using CMake.
This is a stop-gap until we support Python 2 & 3 together in ESP-IDF (soon).
Closes https://github.com/espressif/esp-idf/issues/1924
Added feature:
- reset firmware to Factory app.(by long pressing of the button)
- boot Test app. (by long pressing of the button)
- Added feature erase data partitions from factory reset.
TW10281
TW10280
This includes changing the picture of JTAG jumper block by removing the jumper on S_TDI. It has been reported by a number of users that removing this jumper fixes random communication issues observed in OpenOCD.
Add error handling for http client
set ssid password correct with Example_WIFI test, and clear password before free
Fixed the CI failure due to HTTP errror names
This fixes multiple bugs with ring buffers and re-factors the code. The public
API has not changed, however the underlying implementation have various private
functions have been changed. The following behavioral changes have been made
- Size of ring buffers for No-Split/Allow-Split buffers will not be rounded
up to the nearest 32-bit aligned size. This was done to simplify the
implementation
- Item size for No-Split/Allow-Split buffers will also be rounded up to the
nearest 32-bit aligned size.
The following bugs have been fixed
- In copyItemToRingbufAllowSplit(), when copying an item where the aligned
size is smaller than the remaining length, the function does not consider
the case where the true size of the item is less than 4 bytes.
- The copy functions will automatically wrap around the write pointers when
the remaining length of the buffer is not large enough to fit a header, but
does not consider if wrapping around will cause an overlap with the read
pointer. This will make a full buffer be mistaken for an empty buffer
closes#1711
- xRingbufferSend() can get stuck in a infinite loop when the size of the
free memory is larger than the needed_size, but too small to fit in the ring
buffer due to alignment and extra overhead of wrapping around.
closes#1846
- Fixed documentation with ring buffer queue set API
- Adding and removing from queue set does not consider the case where the
read/write semaphores actually hold a value.
The following functions have been deprecated
- xRingbufferIsNextItemWrapped() due to lack of thread safety
- xRingbufferAddToQueueSetWrite() and xRingbufferRemoveFromQueueSetWrite()
as adding the queue sets only work under receive operations.
The following functions have been added
- xRingbufferReceiveSplit() and xRingbufferReceiveSplitFromISR() as a thread
safe way to receive from allow-split buffers
- vRingbufferGetInfo()
Documentation for ring buffers has also been added.
Added .rtc_noinit and .noinit section definitions into linker file /esp32/ld/esp32.common.ld.
The macro __NOINIT_ATTR, RTC_NOINIT_ATTR declared in esp32/esp_attr.h file.
Added unit test file to test added behavior for noinit variables and its attributes.
Added documentation changes for new added attributes.
Make some corrections after code review:
The linker file has been corrected to place noinit section before bss_start to make it safer.
Documentation file has been modified to clarify reset behavior of allocated data .
Corrected typos in test_noinit.c and removed assertion of noinit variable to avoid possible issues with ROM boot loader memory allocation.
The linker file has been corrected to place noinit section before bss_start to make it safer.
Documentation file has been modified to clarify reset behavior of allocated data .
Corrected typos in test_noinit.c and removed assertion of noinit variable to avoid possible issues with ROM boot loader memory allocation.
Update test_noinit.c file to address RTCWDT_RTC_RESET reset reason instead of POWERON_RESET.
Test optimized to pass automated unit testing.
esp32: Add .noinit and .rtc_noinit sections to the linker script
Update of general-notes.rst documentation to fomat examples as code and attributes as identifiers.
Test test_noinit.c corrected to pass automated testing (support ofTEST_CASE_MULTIPLE_STAGES())
https://ezredmine.espressif.cn:8765/issues/15878
1. add the L1 include path with a prefix, such like osi/list.h, stack/a2d_api.h and etc.
2. modify component, only bluedroid/api/include/api is export to another component and application,
other include path just for bluedroid used
3. put bluedroid/include into common/include/common, so the root directory of bluedroid have no include path.
4. modify doxygen to use esp_bt.h and redirect to
component/bt/bluedroid/api/include/api/
fix compile
Ideally suited for generating a binary externally, containing key-value pairs specific
to device manufacturers. Utility allows creation of a binary, compatible
with NVS structure, which can be separately flashed onto a new
partition. This helps device manufacturers set different values for
different devices, e.g. serial numbers, but using a single firmaware
image.
Need to make the bootloader modular so that users can redefine its functional part.
- refactoring and moving functions to the bootloader_support component
- Changed function to `void` bootloader_utility_load_image(...);
TW19596
- Split SDMMC page into pages about SDMMC/SDSPI hosts and a page about
the protocol layer.
- Use autogenerated API reference instead of manually generated one.
- Add information about SDIO APIs.
The expected usage is:
esp_pthread_set_cfg(cfg);
pthread_create()
If the inherit flag is set, then all subsequent threads forked by this
thread will also inherit this configuration. This avoids having to
change/prefix this for each and every pthread_create() call.
