As heap block may be allocated into multiple non-continuous chunks, to
reserve enough memory for dma/internal usage, we do the malloc in the
step of max available block.
The change fixes thread-local-storage size by removing .srodata section
from it. It initially was included in TLS section by mistake.
The issue was found when stack size increased after building applications
with GCC-11.1 compiler. Stack size became bigger because some new data
appeared in .srodata. See more details here:
adce62f53d
The psram cache bug fix was also being applied to the bootloader binary (for cmake),
which doesnt do any psram access.
Applying this fix would increase the binary size, as much as 300 bytes in worst case scenarios
Additionally, always enable the partition MD5 check if flash encryption is on in
Release mode. This ensures the partition table ciphertext has not been modified
(CVE-2021-27926).
The exception is pre-V3.1 ESP-IDF bootloaders and partition tables, which
don't have support for the MD5 entry.
Since dd849ffc, _rodata_start label has been moved to a different
linker output section from where the TLS templates (.tdata, .tbss)
are located. Since link-time addresses of thread-local variables are
calculated relative to the section start address, this resulted in
incorrect calculation of THREADPTR/$tp registers.
Fix by introducing new linker label, _flash_rodata_start, which points
to the .flash.rodata output section where TLS variables are located,
and use it when calculating THREADPTR/$tp.
Also remove the hardcoded rodata section alignment for Xtensa targets.
Alignment of rodata can be affected by the user application, which is
the issue dd849ffc was fixing. To accommodate any possible alignment,
save it in a linker label (_flash_rodata_align) and then use when
calculating THREADPTR. Note that this is not required on RISC-V, since
this target doesn't use TPOFF.
It is now possible to have any alignment restriction on rodata in the user
applicaiton. It will not affect the first section which must be aligned
on a 16-byte bound.
Closes https://github.com/espressif/esp-idf/issues/6719
When `DIS_USB_JTAG` eFuse is NOT burned (`False`), it is not possible
to set pins 18 and 19 as GPIOs. This commit solves this by manually
disabling USB JTAG when using pins 18 or 19.
The functions shall use `gpio_hal_iomux_func_sel` instead of
`PIN_FUNC_SELELECT`.
Fixes issue with DPORT init task, this task uses minimum stack size and may not be
enough if stack smashing detection is set to Overall mode.
Also reworks the way we calculate minimum stack to allow for adding multiple
contributing factors.
Closes https://github.com/espressif/esp-idf/issues/6403
The CPU might prefetch instructions, which means it in some cases
will try to fetch instruction located after the last instruction in
flash.text.
Add dummy bytes to ensure fetching these wont result in an error,
e.g. MMU exceptions
On S2 the brown out detector would occasionally trigger erroneously during deep sleep.
Disable it before sleeping to circumvent this issue.
Closes https://github.com/espressif/esp-idf/issues/6179
There is no ccomp timer on C3, which means our performance tests will start
failing again due to variance caused by cache misses.
This MR adds TEST_PERFORMANCE_CCOMP_ macro that will only fail
performance test if CCOMP timer is supported on the target
Include external ram section in the linker template to process it
through linker script generation mechanism. This enables redirection of .bss section to external memory using linker fragments
libnet80211, libpp, libbt, liblwip: Redirect .bss through fragments
ESP32 in revision0 and revision1 uses touchpad to provide
current to oscillate xtal 32k. But revision2 and revision3
do not need to do that.
Note: touchpad can not work and toupad/ULP wakeup sources
are not available when toupad provides current to xtal 32k
* Target components pull in xtensa component directly
* Use CPU HAL where applicable
* Remove unnecessary xtensa headers
* Compilation changes necessary to support non-xtensa gcc types (ie int32_t/uint32_t is no
longer signed/unsigned int).
Changes come from internal branch commit a6723fc
During HAL layer refactoring and new chip bringup, we have several
caps.h for each part, to reduce the conflicts to minimum. But this is
The capabilities headers will be relataive stable once completely
written (maybe after the featues are supported by drivers).
Now ESP32 and ESP32-S2 drivers are relative stable, making it a good
time to combine all these caps.h into one soc_caps.h
This cleanup also move HAL config and pin config into separated files,
to make the responsibilities of these headers more clear. This is
helpful for the stabilities of soc_caps.h because we want to make it
public some day.
