Some development boards do not have sufficient external pull-ups on
SD card pins. Most notably, if high level on GPIO13 is not registered
by the card when GO_IDLE_STATE command is received, the card will enter
SPI mode and further communication will not be possible, until power to
the card is toggled.
This change enables internal pull-ups on SD card pins in an attempt to
make this initialization process more reliable.
using apll_param to setup APLL
new apll calculation method, much faster
validate freq calculation
Ensure that the i2s frequency is greater than the hardware limit
Add description of how to calculate apll clock, support apll for other 16-bits audio, check rev0 chip
correct space
All options that were enabled via CONFIG_MDNS are now in menuconfig, with
the default values set the same as with CONFIG_MDNS enabled (meaning existing
projects that were using CONFIG_MDNS do not need to change).
Legacy API of task watchdog used the same function esp_task_wdt_feed() to add
and feed a task. This caused issues of implicitly adding a task to the wdt list
if the function was used in shared code.
The new API introduces init, adding, feeding, deleting, deinit functions. Tasks
must now be explicitly added to the task watchdog using their handles. Deletion
must also be explicit using task handles. This resolves the issue of implicit
task additions to the task watchdog due to shared code calling
esp_task_wdt_feed().
Task watchdog is now fully configurable at runtime by calling the init and
deinit functions.
Also added functions to get the handles of idle tasks of the other core. This
helps when adding idle tasks to the watchdog at run time.
Configuring the task watchdog using menu config is still available, however
menu config will only result in calling the init and add functions for idle
tasks shortly after the scheduler starts.
Menu config also allows for using legacy behavior, however the legacy behavior
willcall the new API functions but with slight variations to make them legacy
compatible.
Documentation and example have also been updated
gcov_rtio.c headers updated to prevent error of freertos header files being
included in the wrong order.
Resolves issue TW#13265
- Separate Eddystone codes into the following 4 files:
esp_eddystone_protocol.h
esp_eddystone_api.h
esp_eddystone_api.c
edp_eddystone_demo.c
- Just store eddystone information into eddystone result
1. Support built-in ADC for I2S.
2. Modify code of ADC, made no change to the original APIs.
3. Add APIs in I2S:
esp_err_t i2s_set_adc_mode(adc_unit_t adc_unit, adc1_channel_t adc_channel);
4. Add I2S ADC/DAC example code.
5. add old-fashion definition to make it more compatible
6. replase spi_flash_ APIs with esp_partition_ APIs
7. add example of generating audio table from wav
8. change example sound
squash again all the commit.
component/bt: Change all the gattc API && bta gattc layer.
component/bt: Debug the code and change the btc_ble_gattc_get_db method.
component/bt: Change the gatt read API interface.
component/bt: Reconstruction the BTA_gattc_cache code.
component/bt: Change back the bluedroid_get_status to marco.
component/bt: Added the serch service res start_handle & end_handle to the result.
component/bt: Change the gattc docs format.
component/bt: Change the docs format.
component/bt: fix the read char value bug.
component/bt: change the gattc_get_attr_count method.
component/bt: Change back the bta_gattc write ccc code.
component/bt: Change the gattc api docs format
component/bt: Change the gattc API docs.
component/bt: Change the prepare write descriptor method to avoid the exection.
Component/bt: modify gatt clinet demo with new API
component/bt: Change the p_src_data->read.p_value to avoid exection.
compoent/bt: Change the bugfix of gattc unreg for the notify.
Modify gattc security demo
component/bt: Change the log error.
Component/bt: modify gattc_multi_connect demo
componnet/bt: Change the bta_gattc_cache sdp include.
component/bt: Change the start_handle & end_handle not from the service.
component/bt: Change the gattc API docs.
component/bt: Change the return issues.
component/bt: Fixed the include service bug.
component/bt: Modify gattc_multi_connect demo , add scan log
component/bt: Fixed the BTA_GATTC_GetIncludeService start handle & end handle error bug.
component/bt: Fix the invalid handle of the get all char issues.
component/bt: Fix the bug with get_db_size_with_type of the start handle & end_handle not correted issue.
component/bt: Fixed the get secondly service num not correct issue.
component/bt: Fixed the last service handle not correted issue.
1. Remove the bond_device global variable.
2. Fix bond_device add cause memory exception
3. Modify the code location.
4. modify thread security
5. remove esp_ble_clear_bond_device_list() API
6. modify esp_ble_get_gond_device_list() to return list immediately, rather than wait event.
7. modify the gatt_security_server demo to show how to remove all the bonded devices.
8. fix some code bugs may cause something error.
- update connection parameters timeout due to master update illegal connection parameters
- slave returns error status when slave check the connection parameters
- slave connection parameters update callback get that interval_max is equal to interval_min
Added component containg API that is able to correct raw ADC readings
into a voltage in mV. Also provided a helper function that combines
the process of getting the raw ADC1 reading then converting it to a
voltage in mV. In doing so, the adc1_get_voltage() function of the ADC
driver has been deprecated. Instead there is now adc1_get_raw to obtain
the raw ADC1 reading, and adc1_to_voltage() that gets the raw reading
and converts all in one function. Functions using the deprecated
adc1_get_voltage() have also been updated to use adc1_get_raw().
Conversion is based on ADC characteristics. The characteristics are based
on the ADC's v_ref, herefore the appropriate structure and functions have
been provided to obtain the ADC characteristics.
The existing ADC driver has also been modified by adding a function to
route the internal ADC reference voltage to a GPIO allowing users to measure
it manually.
Relevant documentation has also been updated
1. add sens_struct.h
2. add definition of RTCCNTL and RTCIO
3. modify touch pad examples
4. update example code.
5. add comments add option in menuconfig
6. fix issue that pad index 8 and 9 are mismatched
7. add touch_pad_read_filtered() api to get value filtered by iir filter
8. modify touch pad isr func
9. Make the items in perihperal.ld in the sequence of address
10. delete Kconfig for touch pad
11. add touchpad filter APIs to adjust the filter
12. add touch_pad into index.rst
13. add touch_pad in Doxyfile
14. add touch_pad.rst
- the first characteristic is used to receive data from client.
- the second characteristic is used to notify data to client.
- the third characteristic is used to receive command from client, user
can add code to process the command.
- the fourth characteristic is used to notify status to client.
- the fifth characteristic is used to keep ble connection
component/bt: cherry-pick the bugfix/btdm_api_manage_pair_info_#13119 to this branch.
component/bt: Change the ble gap API code format & added the status judgment in the btc_storage_load_bonded_ble_devices function.
1. Hello World application shows no footprint difference before and
after this change
2. examples/ethernet/ethernet application compiles properly (can't
test with my board)
Remove wifi config option
Remove Wi-Fi enable/disable option from Kconfig. This can be detected by the presence of esp_wifi_init() function in the application. Minimum footprint impact after the change.
See merge request !1098
1. Rename api from rmt_get_ringbuf_handler to rmt_get_ringbuf_handle (Github Issue #274)
2. doxygen param rename
3. change API rmt_wait_tx_done to specify maximum waiting time
4.Change return type of rmt_wait_tx_done API from bool to esp_err_t
5. update doc
SD SPI mode driver
This MR adds functionality to support SD cards connected via SPI interface.
Additionally, two bugs are fixed:
- Definition of `SPI_TRANS_MODE_DIOQIO_ADDR` in spi_master driver
- SD card probing frequency was 4000kHz instead of 400kHz as required by the standard
See merge request !727
NVS is used to store PHY calibration data, WiFi configuration, and BT
configuration. Previously BT examples did not call nvs_flash_init,
relying on the fact that it is called during PHY init. However PHY init
did not handle possible NVS initialization errors.
This change moves PHY init procedure into the application, and adds
diagnostic messages to BT config management routines if NVS is not
initialized.
unused variable 'lfn'
'isr_handler' defined but not used
'servo_set_angle' defined but not used
'gpio_test_signal' defined but not used
'change_duty' defined but not used
Implements support for system level traces compatible with SEGGER
SystemView tool on top of ESP32 application tracing module.
That kind of traces can help to analyse program's behaviour.
SystemView can show timeline of tasks/ISRs execution, context switches,
statistics related to the CPUs' load distribution etc.
Also this commit adds useful feature to ESP32 application tracing module:
- Trace data buffering is implemented to handle temporary peaks of events load
- Fix slave initiate service discovery procedure
- Fix master re-discovery every time connection established
- Optimize service discovery char ccc write procedure
- Optimize esp_log_buffer function
- Modify default supervision timeout from 20s to 2s
To increase the chances that the examples work out of the box, this
change is raising the default deep sleep wakeup delay to 1ms.
If GPIO15 is low at startup, ROM code takes less time to execute
(because no logging is performed), so more time may be needed to allow
flash chip to become ready.
1. Name change from chopper to carrier, block diagram update, minor changes to example codes
2. mcpwm_reg.h changed, brought uniformity in comments, worked on suggestions, duty to accept float. Some name changes!
3. Minor readme changes and Indetation
4. Minor change: move mcpwm_reg.h and mcpwm_struct.h to new path
5. Minor change: addition of BLDC example code and Readme
6. Name changed from epwm to mcpwm
7. Improve the reg name in mcpwm_struct.h
8. Name change chopper>carrier, deadband>deadtime
add API to get chip info
This change adds an API to get chip info, such as chip model, enabled capabilities, size of embedded flash, silicon revision.
Hello_world example is modified to print out the information about the chip. The example is also simplified by moving all code into the main task.
Ref TW12031.
See merge request !549
Optimize configuration of base MAC address
Application developer can call APIs to configure base MAC address
instead of using menuconfig.
See merge request !744
component/bt: fix adv stop event bug and add attribute table create
- Fix bug that advertising stop event produced while calling start_adv function
- Modify gatt server adv data and scan rsp data raw setting
- Add create attribute table error msg
- Delete redundant printf in previous commits
See merge request !739
