mirror of
https://github.com/espressif/esp-idf.git
synced 2024-10-05 20:47:46 -04:00
support 727 esp32s3 BLE
This commit is contained in:
zwj
parent
9d093d3a04
commit
facadc86d8
@ -65,6 +65,8 @@ config BT_CTRL_HCI_TL
|
||||
default 0 if BT_CTRL_HCI_MODE_UART_H4
|
||||
default 1 if BT_CTRL_HCI_M0DE_VHCI
|
||||
default 1
|
||||
help
|
||||
HCI mode as VHCI or UART(H4)
|
||||
|
||||
config BT_CTRL_ADV_DUP_FILT_MAX
|
||||
int "The maxinum number of 5.0 extend duplicate scan filter"
|
||||
@ -75,7 +77,7 @@ config BT_CTRL_ADV_DUP_FILT_MAX
|
||||
|
||||
config BT_CTRL_HW_CCA
|
||||
bool "HW CCA check enable"
|
||||
default y
|
||||
default n
|
||||
help
|
||||
It enables HW CCA feature in controller
|
||||
|
||||
@ -83,13 +85,9 @@ config BT_CTRL_HW_CCA_EFF
|
||||
int
|
||||
default 1 if BT_CTRL_HW_CCA
|
||||
default 0
|
||||
|
||||
config BT_CTRL_COEX_PARAMETERS_ENABLE
|
||||
bool "Allow Bluetooth preemption in the use of RF to support coexistence with Wi-Fi"
|
||||
default n
|
||||
help
|
||||
Use pre-determined parameter set to control the use of RF by Bluetooth,s
|
||||
so that Bluetooth can compete for RF with Wi-fi to support coexistence.
|
||||
If other devices are sending packets in the air and the signal is strong,
|
||||
the packet hw to be sent this time is cancelled.
|
||||
|
||||
choice BT_CTRL_CE_LENGTH_TYPE
|
||||
prompt "Connection event length determination method"
|
||||
@ -144,10 +142,20 @@ config BT_CTRL_RX_ANTENNA_INDEX_EFF
|
||||
|
||||
choice BT_CTRL_DFT_TX_POWER_LEVEL
|
||||
prompt "BLE default Tx power level"
|
||||
default BT_CTRL_DFT_TX_POWER_LEVEL_P9
|
||||
default BT_CTRL_DFT_TX_POWER_LEVEL_P3
|
||||
help
|
||||
Specify default Tx power level
|
||||
|
||||
config BT_CTRL_DFT_TX_POWER_LEVEL_N27
|
||||
bool "-27dBm"
|
||||
config BT_CTRL_DFT_TX_POWER_LEVEL_N24
|
||||
bool "-24dBm"
|
||||
config BT_CTRL_DFT_TX_POWER_LEVEL_N21
|
||||
bool "-21dBm"
|
||||
config BT_CTRL_DFT_TX_POWER_LEVEL_N18
|
||||
bool "-18dBm"
|
||||
config BT_CTRL_DFT_TX_POWER_LEVEL_N15
|
||||
bool "-15dBm"
|
||||
config BT_CTRL_DFT_TX_POWER_LEVEL_N12
|
||||
bool "-12dBm"
|
||||
config BT_CTRL_DFT_TX_POWER_LEVEL_N9
|
||||
@ -164,25 +172,164 @@ choice BT_CTRL_DFT_TX_POWER_LEVEL
|
||||
bool "+6dBm"
|
||||
config BT_CTRL_DFT_TX_POWER_LEVEL_P9
|
||||
bool "+9dBm"
|
||||
config BT_CTRL_DFT_TX_POWER_LEVEL_P12
|
||||
bool "+12dBm"
|
||||
config BT_CTRL_DFT_TX_POWER_LEVEL_P15
|
||||
bool "+15dBm"
|
||||
config BT_CTRL_DFT_TX_POWER_LEVEL_P18
|
||||
bool "+18dBm"
|
||||
|
||||
endchoice
|
||||
|
||||
config BT_CTRL_DFT_TX_POWER_LEVEL_EFF
|
||||
int
|
||||
default 0 if BT_CTRL_DFT_TX_POWER_LEVEL_N12
|
||||
default 1 if BT_CTRL_DFT_TX_POWER_LEVEL_N9
|
||||
default 2 if BT_CTRL_DFT_TX_POWER_LEVEL_N6
|
||||
default 3 if BT_CTRL_DFT_TX_POWER_LEVEL_N3
|
||||
default 4 if BT_CTRL_DFT_TX_POWER_LEVEL_N0
|
||||
default 5 if BT_CTRL_DFT_TX_POWER_LEVEL_P3
|
||||
default 6 if BT_CTRL_DFT_TX_POWER_LEVEL_P6
|
||||
default 7 if BT_CTRL_DFT_TX_POWER_LEVEL_P9
|
||||
default 0 if BT_CTRL_DFT_TX_POWER_LEVEL_N27
|
||||
default 1 if BT_CTRL_DFT_TX_POWER_LEVEL_N24
|
||||
default 2 if BT_CTRL_DFT_TX_POWER_LEVEL_N21
|
||||
default 3 if BT_CTRL_DFT_TX_POWER_LEVEL_N18
|
||||
default 4 if BT_CTRL_DFT_TX_POWER_LEVEL_N15
|
||||
default 5 if BT_CTRL_DFT_TX_POWER_LEVEL_N12
|
||||
default 6 if BT_CTRL_DFT_TX_POWER_LEVEL_N9
|
||||
default 7 if BT_CTRL_DFT_TX_POWER_LEVEL_N6
|
||||
default 8 if BT_CTRL_DFT_TX_POWER_LEVEL_N3
|
||||
default 9 if BT_CTRL_DFT_TX_POWER_LEVEL_N0
|
||||
default 10 if BT_CTRL_DFT_TX_POWER_LEVEL_P3
|
||||
default 11 if BT_CTRL_DFT_TX_POWER_LEVEL_P6
|
||||
default 12 if BT_CTRL_DFT_TX_POWER_LEVEL_P9
|
||||
default 13 if BT_CTRL_DFT_TX_POWER_LEVEL_P12
|
||||
default 14 if BT_CTRL_DFT_TX_POWER_LEVEL_P15
|
||||
default 15 if BT_CTRL_DFT_TX_POWER_LEVEL_P18
|
||||
|
||||
default 0
|
||||
|
||||
config BT_CTRL_COEX_USE_HOOKS
|
||||
bool "Communicate Bluetooth working status with Wi-Fi to support coexistence"
|
||||
config BT_CTRL_BLE_ADV_REPORT_FLOW_CTRL_SUPP
|
||||
bool "BLE adv report flow control supported"
|
||||
default y
|
||||
help
|
||||
The function is mainly used to enable flow control for advertising reports. When it is enabled,
|
||||
advertising reports will be discarded by the controller if the number of unprocessed advertising
|
||||
reports exceeds the size of BLE adv report flow control.
|
||||
|
||||
config BT_CTRL_BLE_ADV_REPORT_FLOW_CTRL_NUM
|
||||
int "BLE adv report flow control number"
|
||||
depends on BT_CTRL_BLE_ADV_REPORT_FLOW_CTRL_SUPP
|
||||
range 50 1000
|
||||
default 100
|
||||
help
|
||||
The number of unprocessed advertising report that bluetooth host can save.If you set
|
||||
`BT_CTRL_BLE_ADV_REPORT_FLOW_CTRL_NUM` to a small value, this may cause adv packets lost.
|
||||
If you set `BT_CTRL_BLE_ADV_REPORT_FLOW_CTRL_NUM` to a large value, bluetooth host may cache a
|
||||
lot of adv packets and this may cause system memory run out. For example, if you set
|
||||
it to 50, the maximum memory consumed by host is 35 * 50 bytes. Please set
|
||||
`BT_CTRL_BLE_ADV_REPORT_FLOW_CTRL_NUM` according to your system free memory and handle adv
|
||||
packets as fast as possible, otherwise it will cause adv packets lost.
|
||||
|
||||
config BT_CTRL_BLE_ADV_REPORT_DISCARD_THRSHOLD
|
||||
int "BLE adv lost event threshold value"
|
||||
depends on BT_CTRL_BLE_ADV_REPORT_FLOW_CTRL_SUPP
|
||||
range 1 1000
|
||||
default 20
|
||||
help
|
||||
When adv report flow control is enabled, The ADV lost event will be generated when the number
|
||||
of ADV packets lost in the controller reaches this threshold. It is better to set a larger value.
|
||||
If you set `BT_CTRL_BLE_ADV_REPORT_DISCARD_THRSHOLD` to a small value or printf every adv lost event, it
|
||||
may cause adv packets lost more.
|
||||
|
||||
config BT_CTRL_BLE_SCAN_DUPL
|
||||
bool "BLE Scan Duplicate Options"
|
||||
default y
|
||||
help
|
||||
This select enables parameters setting of BLE scan duplicate.
|
||||
|
||||
choice BT_CTRL_SCAN_DUPL_TYPE
|
||||
prompt "Scan Duplicate Type"
|
||||
default BT_CTRL_SCAN_DUPL_TYPE_DEVICE
|
||||
depends on BT_CTRL_BLE_SCAN_DUPL
|
||||
help
|
||||
Scan duplicate have three ways. one is "Scan Duplicate By Device Address", This way is to use
|
||||
advertiser address filtering. The adv packet of the same address is only allowed to be reported once.
|
||||
Another way is "Scan Duplicate By Device Address And Advertising Data". This way is to use advertising
|
||||
data and device address filtering. All different adv packets with the same address are allowed to be
|
||||
reported. The last way is "Scan Duplicate By Advertising Data". This way is to use advertising data
|
||||
filtering. All same advertising data only allow to be reported once even though they are from
|
||||
different devices.
|
||||
|
||||
config BT_CTRL_SCAN_DUPL_TYPE_DEVICE
|
||||
bool "Scan Duplicate By Device Address"
|
||||
help
|
||||
This way is to use advertiser address filtering. The adv packet of the same address is only
|
||||
allowed to be reported once
|
||||
|
||||
config BT_CTRL_SCAN_DUPL_TYPE_DATA
|
||||
bool "Scan Duplicate By Advertising Data"
|
||||
help
|
||||
This way is to use advertising data filtering. All same advertising data only allow to be reported
|
||||
once even though they are from different devices.
|
||||
|
||||
config BT_CTRL_SCAN_DUPL_TYPE_DATA_DEVICE
|
||||
bool "Scan Duplicate By Device Address And Advertising Data"
|
||||
help
|
||||
This way is to use advertising data and device address filtering. All different adv packets with
|
||||
the same address are allowed to be reported.
|
||||
endchoice
|
||||
|
||||
config BT_CTRL_SCAN_DUPL_TYPE
|
||||
int
|
||||
depends on BT_CTRL_BLE_SCAN_DUPL
|
||||
default 0 if BT_CTRL_SCAN_DUPL_TYPE_DEVICE
|
||||
default 1 if BT_CTRL_SCAN_DUPL_TYPE_DATA
|
||||
default 2 if BT_CTRL_SCAN_DUPL_TYPE_DATA_DEVICE
|
||||
default 0
|
||||
|
||||
config BT_CTRL_SCAN_DUPL_CACHE_SIZE
|
||||
int "Maximum number of devices in scan duplicate filter"
|
||||
depends on BT_CTRL_BLE_SCAN_DUPL
|
||||
range 10 1000
|
||||
default 100
|
||||
help
|
||||
Maximum number of devices which can be recorded in scan duplicate filter.
|
||||
When the maximum amount of device in the filter is reached, the cache will be refreshed.
|
||||
|
||||
config BT_CTRL_BLE_MESH_SCAN_DUPL_EN
|
||||
bool "Special duplicate scan mechanism for BLE Mesh scan"
|
||||
depends on BT_CTRL_BLE_SCAN_DUPL
|
||||
default n
|
||||
help
|
||||
Send notifications of Bluetooth working status to support coexistence with Wi-Fi.
|
||||
This enables the BLE scan duplicate for special BLE Mesh scan.
|
||||
|
||||
config BT_CTRL_MESH_DUPL_SCAN_CACHE_SIZE
|
||||
int "Maximum number of Mesh adv packets in scan duplicate filter"
|
||||
depends on BT_CTRL_BLE_MESH_SCAN_DUPL_EN
|
||||
range 10 1000
|
||||
default 100
|
||||
help
|
||||
Maximum number of adv packets which can be recorded in duplicate scan cache for BLE Mesh.
|
||||
When the maximum amount of device in the filter is reached, the cache will be refreshed.
|
||||
|
||||
choice BT_CTRL_COEX_PHY_CODED_TX_RX_TLIM
|
||||
prompt "Coexistence: limit on MAX Tx/Rx time for coded-PHY connection"
|
||||
default BT_CTRL_COEX_PHY_CODED_TX_RX_TLIM_DIS
|
||||
depends on ESP32_WIFI_SW_COEXIST_ENABLE
|
||||
help
|
||||
When using PHY-Coded in BLE connection, limitation on max tx/rx time can be applied to
|
||||
better avoid dramatic performance deterioration of Wi-Fi.
|
||||
|
||||
config BT_CTRL_COEX_PHY_CODED_TX_RX_TLIM_EN
|
||||
bool "Force Enable"
|
||||
help
|
||||
Always enable the limitation on max tx/rx time for Coded-PHY connection
|
||||
|
||||
config BT_CTRL_COEX_PHY_CODED_TX_RX_TLIM_DIS
|
||||
bool "Force Disable"
|
||||
help
|
||||
Disable the limitation on max tx/rx time for Coded-PHY connection
|
||||
endchoice
|
||||
|
||||
config BT_CTRL_COEX_PHY_CODED_TX_RX_TLIM_EFF
|
||||
int
|
||||
default 0 if (!ESP32_WIFI_SW_COEXIST_ENABLE)
|
||||
default 1 if BT_CTRL_COEX_PHY_CODED_TX_RX_TLIM_EN
|
||||
default 0 if BT_CTRL_COEX_PHY_CODED_TX_RX_TLIM_DIS
|
||||
|
||||
menu "MODEM SLEEP Options"
|
||||
visible if BT_ENABLED
|
||||
@ -217,8 +364,22 @@ menu "MODEM SLEEP Options"
|
||||
selected, bluetooth modem sleep can work under Dynamic Frequency Scaling(DFS) enabled, but
|
||||
cannot work when light sleep is enabled. Main crystal has a relatively better performance than
|
||||
other bluetooth low power clock sources.
|
||||
endchoice
|
||||
config BT_CTRL_LPCLK_SEL_EXT_32K_XTAL
|
||||
bool "External 32kHz crystal"
|
||||
depends on ESP32S3_RTC_CLK_SRC_EXT_CRYS
|
||||
help
|
||||
External 32kHz crystal has a nominal frequency of 32.768kHz and provides good frequency
|
||||
stability. If used as Bluetooth low power clock, External 32kHz can support Bluetooth
|
||||
modem sleep to be used with both DFS and light sleep.
|
||||
|
||||
config BT_CTRL_LPCLK_SEL_RTC_SLOW
|
||||
bool "Internal 90kHz RC oscillator"
|
||||
depends on ESP32S3_RTC_CLK_SRC_INT_RC
|
||||
help
|
||||
Internal 90kHz RC oscillator.
|
||||
|
||||
|
||||
endchoice
|
||||
endmenu
|
||||
|
||||
config BT_CTRL_SLEEP_MODE_EFF
|
||||
@ -229,6 +390,8 @@ config BT_CTRL_SLEEP_MODE_EFF
|
||||
config BT_CTRL_SLEEP_CLOCK_EFF
|
||||
int
|
||||
default 1 if BT_CTRL_LPCLK_SEL_MAIN_XTAL
|
||||
default 2 if BT_CTRL_LPCLK_SEL_EXT_32K_XTAL
|
||||
default 3 if BT_CTRL_LPCLK_SEL_RTC_SLOW
|
||||
|
||||
default 0
|
||||
|
||||
|
||||
File diff suppressed because it is too large
Load Diff
@ -1 +1 @@
|
||||
Subproject commit 2b7816260ecd12710b983b7c859d42fce4f7d979
|
||||
Subproject commit a7d76980fe7687053bebaa145095e4e3584f6150
|
||||
@ -25,8 +25,8 @@
|
||||
extern "C" {
|
||||
#endif
|
||||
|
||||
#define ESP_BT_CTRL_CONFIG_MAGIC_VAL 0x5A5AA5A5
|
||||
#define ESP_BT_CTRL_CONFIG_VERSION 0x02004260
|
||||
#define ESP_BT_CTRL_CONFIG_MAGIC_VAL 0x5A5AA5A5
|
||||
#define ESP_BT_CTRL_CONFIG_VERSION 0x02103080
|
||||
|
||||
#define ESP_BT_HCI_TL_MAGIC_VALUE 0xfadebead
|
||||
#define ESP_BT_HCI_TL_VERSION 0x00010000
|
||||
@ -73,7 +73,8 @@ typedef enum {
|
||||
ESP_BT_SLEEP_CLOCK_NONE = 0, /*!< Sleep clock not configured */
|
||||
ESP_BT_SLEEP_CLOCK_MAIN_XTAL = 1, /*!< SoC main crystal */
|
||||
ESP_BT_SLEEP_CLOCK_EXT_32K_XTAL = 2, /*!< External 32.768kHz crystal */
|
||||
ESP_BT_SLEEP_CLOCK_FPGA_32K = 3, /*!< Hardwired 32KHz clock temporarily used for FPGA */
|
||||
ESP_BT_SLEEP_CLOCK_RTC_SLOW = 3, /*!< Internal 90kHz RC oscillator */
|
||||
ESP_BT_SLEEP_CLOCK_FPGA_32K = 4, /*!< Hardwired 32KHz clock temporarily used for FPGA */
|
||||
} esp_bt_sleep_clock_t;
|
||||
|
||||
/**
|
||||
@ -84,22 +85,55 @@ enum {
|
||||
ESP_BT_ANT_IDX_1 = 1, /*!< anntena NO 1 */
|
||||
};
|
||||
|
||||
/**
|
||||
* @brief Maximum Tx/Rx time limit on Coded-PHY connection
|
||||
*/
|
||||
enum {
|
||||
ESP_BT_COEX_PHY_CODED_TX_RX_TIME_LIMIT_FORCE_DISABLE = 0, /*!< Disable the limit */
|
||||
ESP_BT_COEX_PHY_CODED_TX_RX_TIME_LIMIT_FORCE_ENABLE, /*!< Always Enable the limit */
|
||||
};
|
||||
|
||||
#ifdef CONFIG_BT_ENABLED
|
||||
|
||||
#ifdef CONFIG_BT_CTRL_COEX_PARAMETERS_ENABLE
|
||||
#define BT_CTRL_COEX_PARAMETERS_ENABLE true
|
||||
#else
|
||||
#define BT_CTRL_COEX_PARAMETERS_ENABLE false
|
||||
#endif
|
||||
|
||||
#ifdef CONFIG_BT_CTRL_COEX_USE_HOOKS
|
||||
#define BT_CTRL_COEX_USE_HOOKS true
|
||||
#else
|
||||
#define BT_CTRL_COEX_USE_HOOKS false
|
||||
#endif
|
||||
|
||||
#define BT_CTRL_BLE_MAX_ACT_LIMIT 10 //Maximum BLE activity limitation
|
||||
|
||||
#ifdef CONFIG_BT_CTRL_SCAN_DUPL_TYPE
|
||||
#define SCAN_DUPLICATE_TYPE_VALUE CONFIG_BT_CTRL_SCAN_DUPL_TYPE
|
||||
#else
|
||||
#define SCAN_DUPLICATE_TYPE_VALUE 0
|
||||
#endif
|
||||
|
||||
/* normal adv cache size */
|
||||
#ifdef CONFIG_BT_CTRL_SCAN_DUPL_CACHE_SIZE
|
||||
#define NORMAL_SCAN_DUPLICATE_CACHE_SIZE CONFIG_BT_CTRL_SCAN_DUPL_CACHE_SIZE
|
||||
#else
|
||||
#define NORMAL_SCAN_DUPLICATE_CACHE_SIZE 20
|
||||
#endif
|
||||
|
||||
#ifndef CONFIG_BT_CTRL_BLE_MESH_SCAN_DUPL_EN
|
||||
#define CONFIG_BT_CTRL_BLE_MESH_SCAN_DUPL_EN FALSE
|
||||
#endif
|
||||
|
||||
#define SCAN_DUPLICATE_MODE_NORMAL_ADV_ONLY 0
|
||||
#define SCAN_DUPLICATE_MODE_NORMAL_ADV_MESH_ADV 1
|
||||
|
||||
#if CONFIG_BT_CTRL_BLE_MESH_SCAN_DUPL_EN
|
||||
#define SCAN_DUPLICATE_MODE SCAN_DUPLICATE_MODE_NORMAL_ADV_MESH_ADV
|
||||
#ifdef CONFIG_BT_CTRL_MESH_DUPL_SCAN_CACHE_SIZE
|
||||
#define MESH_DUPLICATE_SCAN_CACHE_SIZE CONFIG_BT_CTRL_MESH_DUPL_SCAN_CACHE_SIZE
|
||||
#else
|
||||
#define MESH_DUPLICATE_SCAN_CACHE_SIZE 50
|
||||
#endif
|
||||
#else
|
||||
#define SCAN_DUPLICATE_MODE SCAN_DUPLICATE_MODE_NORMAL_ADV_ONLY
|
||||
#define MESH_DUPLICATE_SCAN_CACHE_SIZE 0
|
||||
#endif
|
||||
|
||||
#define CFG_MASK_BIT_SCAN_DUPLICATE_OPTION (1<<0)
|
||||
|
||||
#define CFG_MASK CFG_MASK_BIT_SCAN_DUPLICATE_OPTION
|
||||
|
||||
#define BLE_HW_TARGET_CODE_ESP32S3_CHIP_ECO0 (0x02010000)
|
||||
|
||||
#define BT_CONTROLLER_INIT_CONFIG_DEFAULT() { \
|
||||
.magic = ESP_BT_CTRL_CONFIG_MAGIC_VAL, \
|
||||
@ -114,17 +148,21 @@ enum {
|
||||
.ble_st_acl_tx_buf_nb = CONFIG_BT_CTRL_BLE_STATIC_ACL_TX_BUF_NB, \
|
||||
.ble_hw_cca_check = CONFIG_BT_CTRL_HW_CCA_EFF, \
|
||||
.ble_adv_dup_filt_max = CONFIG_BT_CTRL_ADV_DUP_FILT_MAX, \
|
||||
.coex_param_en = BT_CTRL_COEX_PARAMETERS_ENABLE, \
|
||||
.ce_len_type = CONFIG_BT_CTRL_CE_LENGTH_TYPE_EFF, \
|
||||
.coex_use_hooks = BT_CTRL_COEX_USE_HOOKS, \
|
||||
.hci_tl_type = CONFIG_BT_CTRL_HCI_TL_EFF, \
|
||||
.hci_tl_funcs = NULL, \
|
||||
.txant_dft = CONFIG_BT_CTRL_TX_ANTENNA_INDEX_EFF, \
|
||||
.rxant_dft = CONFIG_BT_CTRL_RX_ANTENNA_INDEX_EFF, \
|
||||
.txpwr_dft = CONFIG_BT_CTRL_DFT_TX_POWER_LEVEL_EFF, \
|
||||
.cfg_mask = CFG_MASK, \
|
||||
.scan_duplicate_mode = SCAN_DUPLICATE_MODE, \
|
||||
.scan_duplicate_type = SCAN_DUPLICATE_TYPE_VALUE, \
|
||||
.normal_adv_size = NORMAL_SCAN_DUPLICATE_CACHE_SIZE, \
|
||||
.mesh_adv_size = MESH_DUPLICATE_SCAN_CACHE_SIZE, \
|
||||
.coex_phy_coded_tx_rx_time_limit = CONFIG_BT_CTRL_COEX_PHY_CODED_TX_RX_TLIM_EFF, \
|
||||
.hw_target_code = BLE_HW_TARGET_CODE_ESP32S3_CHIP_ECO0, \
|
||||
};
|
||||
|
||||
|
||||
#else
|
||||
#define BT_CONTROLLER_INIT_CONFIG_DEFAULT() {0}; _Static_assert(0, "please enable bluetooth in menuconfig to use bt.h");
|
||||
#endif
|
||||
@ -172,14 +210,21 @@ typedef struct {
|
||||
uint8_t ble_st_acl_tx_buf_nb; /*!< controller static ACL TX BUFFER number */
|
||||
uint8_t ble_hw_cca_check; /*!< controller hardware triggered CCA check */
|
||||
uint16_t ble_adv_dup_filt_max; /*!< maxinum number of duplicate scan filter */
|
||||
bool coex_param_en; /*!< init coex parameters*/
|
||||
bool coex_param_en; /*!< deprecated */
|
||||
uint8_t ce_len_type; /*!< connection event length computation method */
|
||||
bool coex_use_hooks; /*!< use hooks in bluetooth to assist WiFi behavouir determination */
|
||||
bool coex_use_hooks; /*!< deprecated */
|
||||
uint8_t hci_tl_type; /*!< HCI transport layer, UART, VHCI, etc */
|
||||
esp_bt_hci_tl_t *hci_tl_funcs; /*!< hci transport functions used, must be set when hci_tl_type is UART */
|
||||
uint8_t txant_dft; /*!< default Tx antenna */
|
||||
uint8_t rxant_dft; /*!< default Rx antenna */
|
||||
uint8_t txpwr_dft; /*!< default Tx power */
|
||||
uint32_t cfg_mask;
|
||||
uint8_t scan_duplicate_mode; /*!< scan duplicate mode */
|
||||
uint8_t scan_duplicate_type; /*!< scan duplicate type */
|
||||
uint16_t normal_adv_size; /*!< Normal adv size for scan duplicate */
|
||||
uint16_t mesh_adv_size; /*!< Mesh adv size for scan duplicate */
|
||||
uint8_t coex_phy_coded_tx_rx_time_limit; /*!< limit on max tx/rx time in case of connection using CODED-PHY with Wi-Fi coexistence */
|
||||
uint32_t hw_target_code; /*!< hardware target */
|
||||
} esp_bt_controller_config_t;
|
||||
|
||||
/**
|
||||
@ -222,14 +267,23 @@ typedef enum {
|
||||
* @brief Bluetooth TX power level(index), it's just a index corresponding to power(dbm).
|
||||
*/
|
||||
typedef enum {
|
||||
ESP_PWR_LVL_N12 = 0, /*!< Corresponding to -12dbm */
|
||||
ESP_PWR_LVL_N9 = 1, /*!< Corresponding to -9dbm */
|
||||
ESP_PWR_LVL_N6 = 2, /*!< Corresponding to -6dbm */
|
||||
ESP_PWR_LVL_N3 = 3, /*!< Corresponding to -3dbm */
|
||||
ESP_PWR_LVL_N0 = 4, /*!< Corresponding to 0dbm */
|
||||
ESP_PWR_LVL_P3 = 5, /*!< Corresponding to +3dbm */
|
||||
ESP_PWR_LVL_P6 = 6, /*!< Corresponding to +6dbm */
|
||||
ESP_PWR_LVL_P9 = 7, /*!< Corresponding to +9dbm */
|
||||
ESP_PWR_LVL_N27 = 0, /*!< Corresponding to -27dbm */
|
||||
ESP_PWR_LVL_N24 = 1, /*!< Corresponding to -24dbm */
|
||||
ESP_PWR_LVL_N21 = 2, /*!< Corresponding to -21dbm */
|
||||
ESP_PWR_LVL_N18 = 3, /*!< Corresponding to -18dbm */
|
||||
ESP_PWR_LVL_N15 = 4, /*!< Corresponding to -15dbm */
|
||||
ESP_PWR_LVL_N12 = 5, /*!< Corresponding to -12dbm */
|
||||
ESP_PWR_LVL_N9 = 6, /*!< Corresponding to -9dbm */
|
||||
ESP_PWR_LVL_N6 = 7, /*!< Corresponding to -6dbm */
|
||||
ESP_PWR_LVL_N3 = 8, /*!< Corresponding to -3dbm */
|
||||
ESP_PWR_LVL_N0 = 9, /*!< Corresponding to 0dbm */
|
||||
ESP_PWR_LVL_P3 = 10, /*!< Corresponding to +3dbm */
|
||||
ESP_PWR_LVL_P6 = 11, /*!< Corresponding to +6dbm */
|
||||
ESP_PWR_LVL_P9 = 12, /*!< Corresponding to +9dbm */
|
||||
ESP_PWR_LVL_P12 = 13, /*!< Corresponding to +12dbm */
|
||||
ESP_PWR_LVL_P15 = 14, /*!< Corresponding to +15dbm */
|
||||
ESP_PWR_LVL_P18 = 15, /*!< Corresponding to +18dbm */
|
||||
ESP_PWR_LVL_INVALID = 0xFF, /*!< Indicates an invalid value */
|
||||
} esp_power_level_t;
|
||||
|
||||
/**
|
||||
|
||||
Loading…
Reference in New Issue
Block a user