diff --git a/docs/en/api-reference/peripherals/gpio.rst b/docs/en/api-reference/peripherals/gpio.rst
index df0e291360..a6ae8fe326 100644
--- a/docs/en/api-reference/peripherals/gpio.rst
+++ b/docs/en/api-reference/peripherals/gpio.rst
@@ -10,7 +10,13 @@ GPIO Summary
     :start-after: gpio-summary
     :end-before: ---
 
-GPIO driver offers a dump function :cpp:func:`gpio_dump_io_configuration` to show the configurations of the IOs at the moment, such as pull-up / pull-down, input / output enable, pin mapping etc. Below is an example dump:
+GPIO driver offers a dump function :cpp:func:`gpio_dump_io_configuration` to show the current configurations of IOs, such as pull-up/pull-down, input/output enable, pin mapping, etc. Below is an example of how to dump the configuration of GPIO4, GPIO18, and GPIO26:
+
+::
+
+    gpio_dump_io_configuration(stdout, (1ULL << 4) | (1ULL << 18) | (1ULL << 26));
+
+The dump will be like this:
 
 ::
 
@@ -37,6 +43,12 @@ GPIO driver offers a dump function :cpp:func:`gpio_dump_io_configuration` to sho
 
     =================IO DUMP End==================
 
+In addition, if you would like to dump the configurations of all IOs, you can use:
+
+::
+
+    gpio_dump_all_io_configuration(stdout, SOC_GPIO_VALID_GPIO_MASK);
+
 If an IO pin is routed to a peripheral signal through the GPIO matrix, the signal ID printed in the dump information is defined in the ``soc/gpio_sig_map.h`` file. The word ``**RESERVED**`` indicates the IO is occupied by either FLASH or PSRAM. It is strongly not recommended to reconfigure them for other application purposes.
 
 .. only:: SOC_RTCIO_INPUT_OUTPUT_SUPPORTED
diff --git a/docs/zh_CN/api-reference/peripherals/gpio.rst b/docs/zh_CN/api-reference/peripherals/gpio.rst
index 99db11cffd..a6d0399541 100644
--- a/docs/zh_CN/api-reference/peripherals/gpio.rst
+++ b/docs/zh_CN/api-reference/peripherals/gpio.rst
@@ -10,7 +10,13 @@ GPIO 汇总
     :start-after: gpio-summary
     :end-before: ---
 
-GPIO 驱动提供了一个函数 :cpp:func:`gpio_dump_io_configuration` 用来输出指定管脚的实时配置状态，包括上下拉、输入输出使能、管脚映射等。输出示例如下：
+GPIO 驱动提供了一个函数 :cpp:func:`gpio_dump_io_configuration` 用来输出指定管脚的实时配置状态，包括上下拉、输入输出使能、管脚映射等。例如，以下命令可用于输出 GPIO4，GPIO8 与 GPIO26 的配置状态：
+
+::
+
+    gpio_dump_io_configuration(stdout, (1ULL << 4) | (1ULL << 18) | (1ULL << 26));
+
+其输出信息如下：
 
 ::
 
@@ -37,6 +43,12 @@ GPIO 驱动提供了一个函数 :cpp:func:`gpio_dump_io_configuration` 用来
 
     =================IO DUMP End==================
 
+如果你想要查看所有管脚的配置状态，可以使用命令
+
+::
+
+    gpio_dump_all_io_configuration(stdout, SOC_GPIO_VALID_GPIO_MASK);
+
 当 IO 管脚是通过 GPIO 交换矩阵连接到内部外设信号，输出信息打印中的外设信号 ID 定义可以在 ``soc/gpio_sig_map.h`` 文件中查看。``**RESERVED**`` 字样则表示此 IO 被用于连接 FLASH 或 PSRAM，因此该引脚不应该被其他任何应用场景所征用并进行重新配置。
 
 .. only:: SOC_RTCIO_INPUT_OUTPUT_SUPPORTED