docs: Fix ADC pad and MOSI typo, update esp32c3 rom elf link

docs/en/api-guides/ulp_instruction_set.rst

@@ -3,7 +3,7 @@ ESP32 ULP coprocessor instruction set
 
 This document provides details about the instructions used by ESP32 ULP coprocessor assembler.
 
-ULP coprocessor has 4 16-bit general purpose registers, labeled R0, R1, R2, R3. It also has an 8-bit counter register (stage_cnt) which can be used to implement loops. Stage count regiter is accessed using special instructions.
+ULP coprocessor has 4 16-bit general purpose registers, labeled R0, R1, R2, R3. It also has an 8-bit counter register (stage_cnt) which can be used to implement loops. Stage count register is accessed using special instructions.
 
 ULP coprocessor can access 8k bytes of RTC_SLOW_MEM memory region. Memory is addressed in 32-bit word units. It can also access peripheral registers in RTC_CNTL, RTC_IO, and SENS peripherals.
 
@@ -73,7 +73,7 @@ ULP coprocessor is clocked from RTC_FAST_CLK, which is normally derived from the
     uint32_t rtc_8md256_period = rtc_clk_cal(RTC_CAL_8MD256, 100);
     uint32_t rtc_fast_freq_hz = 1000000ULL * (1 << RTC_CLK_CAL_FRACT) * 256 / rtc_8md256_period;
 
-ULP coprocessor needs certain number of clock cycles to fetch each instuction, plus certain number of cycles to execute it, depending on the instruction. See description of each instruction below for details on the execution time.
+ULP coprocessor needs certain number of clock cycles to fetch each instruction, plus certain number of cycles to execute it, depending on the instruction. See description of each instruction below for details on the execution time.
 
 Instruction fetch time is:
 
@@ -639,7 +639,7 @@ Note that when accessing RTC memories and RTC registers, ULP coprocessor has low
 
   1:        STAGE_DEC      10        // stage_cnt -= 10;
 
-  2:        // Down counting loop exaple
+  2:        // Down counting loop example
             STAGE_RST                // set stage_cnt to 0
             STAGE_INC  16            // increment stage_cnt to 16
     label:  STAGE_DEC  1             // stage_cnt--;
@@ -786,7 +786,7 @@ Note that when accessing RTC memories and RTC registers, ULP coprocessor has low
 **Operands**
   - *Rdst* – Destination Register R[0..3], result will be stored to this register
   - *Sar_sel* – Select ADC: 0 = SARADC1, 1 = SARADC2
-  - *Mux*  -  selected PAD, SARADC Pad[Mux+1] is enabled
+  - *Mux*  - Enable ADC channel. Channel number is [Mux-1]. If the user passes Mux value 1, then ADC channel 0 gets used.
 
 **Cycles**
   ``23 + max(1, SAR_AMP_WAIT1) + max(1, SAR_AMP_WAIT2) + max(1, SAR_AMP_WAIT3) + SARx_SAMPLE_CYCLE + SARx_SAMPLE_BIT`` cycles to execute, 4 cycles to fetch next instruction
@@ -796,7 +796,7 @@ Note that when accessing RTC memories and RTC registers, ULP coprocessor has low
 
 **Examples**::
 
-   1:        ADC      R1, 0, 1      // Measure value using ADC1 pad 2 and store result into R1
+   1:        ADC      R1, 0, 1      // Measure value using ADC1 channel 0 and store result into R1
 
 **I2C_RD** - read single byte from I2C slave
 ----------------------------------------------

docs/en/api-reference/peripherals/spi_slave.rst

@@ -27,7 +27,7 @@ Term               Definition
 **Device**         SPI slave device, in this case the SPI2 and SPI3 controllers. Each Device shares the MOSI, MISO and SCLK signals but is only active on the bus when the Host asserts the Device's individual CS line.
 **Bus**            A signal bus, common to all Devices connected to one Host. In general, a bus includes the following lines: MISO, MOSI, SCLK, one or more CS lines, and, optionally, QUADWP and QUADHD. So Devices are connected to the same lines, with the exception that each Device has its own CS line. Several Devices can also share one CS line if connected in the daisy-chain manner.
 - **MISO**         Master In, Slave Out, a.k.a. Q. Data transmission from a Device to Host.
-- **MOSI**         Master In, Slave Out, a.k.a. D. Data transmission from a Host to Device.
+- **MOSI**         Master Out, Slave in, a.k.a. D. Data transmission from a Host to Device.
 - **SCLK**         Serial Clock. Oscillating signal generated by a Host that keeps the transmission of data bits in sync.
 - **CS**           Chip Select. Allows a Host to select individual Device(s) connected to the bus in order to send or receive data.
 - **QUADWP**       Write Protect signal. Only used for 4-bit (qio/qout) transactions.