fix(console): enable to select UART1 port for console output

This feature was only enabled for esp32, esp32s2, esp32s3 previously.
Now, enabling this feature for all targets.

components/bootloader_support/src/bootloader_console.c

@@ -38,6 +38,7 @@ void bootloader_console_init(void)
 void bootloader_console_init(void)
 {
     const int uart_num = CONFIG_ESP_CONSOLE_UART_NUM;
+    int __DECLARE_RCC_ATOMIC_ENV __attribute__ ((unused)); // To avoid build errors/warnings about __DECLARE_RCC_ATOMIC_ENV
 
     // Install rom uart printf as console.
     esp_rom_install_uart_printf();
@@ -59,8 +60,8 @@ void bootloader_console_init(void)
             uart_tx_gpio != UART_NUM_0_TXD_DIRECT_GPIO_NUM ||
             uart_rx_gpio != UART_NUM_0_RXD_DIRECT_GPIO_NUM) {
         // Change default UART pins back to GPIOs
-        gpio_hal_iomux_func_sel(PERIPHS_IO_MUX_U0RXD_U, PIN_FUNC_GPIO);
+        gpio_hal_iomux_func_sel(GPIO_PIN_MUX_REG[UART_NUM_0_RXD_DIRECT_GPIO_NUM], PIN_FUNC_GPIO);
-        gpio_hal_iomux_func_sel(PERIPHS_IO_MUX_U0TXD_U, PIN_FUNC_GPIO);
+        gpio_hal_iomux_func_sel(GPIO_PIN_MUX_REG[UART_NUM_0_TXD_DIRECT_GPIO_NUM], PIN_FUNC_GPIO);
         // Route GPIO signals to/from pins
         const uint32_t tx_idx = UART_PERIPH_SIGNAL(uart_num, SOC_UART_TX_PIN_IDX);
         const uint32_t rx_idx = UART_PERIPH_SIGNAL(uart_num, SOC_UART_RX_PIN_IDX);
@@ -71,7 +72,11 @@ void bootloader_console_init(void)
         esp_rom_gpio_connect_in_signal(uart_rx_gpio, rx_idx, 0);
         gpio_hal_iomux_func_sel(GPIO_PIN_MUX_REG[uart_tx_gpio], PIN_FUNC_GPIO);
         // Enable the peripheral
-        periph_ll_enable_clk_clear_rst(PERIPH_UART0_MODULE + uart_num);
+        uart_ll_enable_bus_clock(uart_num, true);
+        uart_ll_reset_register(uart_num);
+        // Reset TX and RX FIFOs
+        uart_ll_txfifo_rst(UART_LL_GET_HW(uart_num));
+        uart_ll_rxfifo_rst(UART_LL_GET_HW(uart_num));
     }
 #endif // CONFIG_ESP_CONSOLE_UART_CUSTOM
 
@@ -80,7 +85,6 @@ void bootloader_console_init(void)
 #if ESP_ROM_UART_CLK_IS_XTAL
     clock_hz = (uint32_t)rtc_clk_xtal_freq_get() * MHZ; // From esp32-s3 on, UART clk source is selected to XTAL in ROM
 #endif
-    int __DECLARE_RCC_ATOMIC_ENV __attribute__ ((unused)); // To avoid build errors/warnings about __DECLARE_RCC_ATOMIC_ENV
     esp_rom_uart_set_clock_baudrate(uart_num, clock_hz, CONFIG_ESP_CONSOLE_UART_BAUDRATE);
 }
 #endif // CONFIG_ESP_CONSOLE_UART

components/driver/uart/uart.c

@@ -183,23 +183,9 @@ static void uart_module_enable(uart_port_t uart_num)
                 uart_ll_enable_bus_clock(uart_num, true);
             }
             if (uart_num != CONFIG_ESP_CONSOLE_UART_NUM) {
-                // Workaround for ESP32C3/S3: enable core reset before enabling uart module clock to prevent uart output
-                // garbage value.
-#if SOC_UART_REQUIRE_CORE_RESET
-                HP_UART_SRC_CLK_ATOMIC(){
-                    uart_hal_set_reset_core(&(uart_context[uart_num].hal), true);
-                }
                 HP_UART_BUS_CLK_ATOMIC() {
                     uart_ll_reset_register(uart_num);
                 }
-                HP_UART_SRC_CLK_ATOMIC(){
-                    uart_hal_set_reset_core(&(uart_context[uart_num].hal), false);
-                }
-#else
-                HP_UART_BUS_CLK_ATOMIC() {
-                    uart_ll_reset_register(uart_num);
-                }
-#endif
             }
         }
 #if (SOC_UART_LP_NUM >= 1)

components/esp_system/Kconfig

@@ -275,13 +275,9 @@ menu "ESP System Settings"
         bool
         default y if ESP_CONSOLE_UART_DEFAULT || ESP_CONSOLE_UART_CUSTOM
 
-    config ESP_CONSOLE_MULTIPLE_UART
-        bool
-        default y if !IDF_TARGET_ESP32C3 && !IDF_TARGET_ESP32H2 && !IDF_TARGET_ESP32C2 && !IDF_TARGET_ESP32C6
-
     choice ESP_CONSOLE_UART_NUM
         prompt "UART peripheral to use for console output (0-1)"
-        depends on ESP_CONSOLE_UART_CUSTOM && ESP_CONSOLE_MULTIPLE_UART
+        depends on ESP_CONSOLE_UART_CUSTOM
         default ESP_CONSOLE_UART_CUSTOM_NUM_0
         help
             This UART peripheral is used for console output from the ESP-IDF Bootloader and the app.
@@ -301,7 +297,6 @@ menu "ESP System Settings"
     config ESP_CONSOLE_UART_NUM
         int
         default 0 if ESP_CONSOLE_UART_DEFAULT
-        default 0 if !ESP_CONSOLE_MULTIPLE_UART
         default 0 if ESP_CONSOLE_UART_CUSTOM_NUM_0
         default 1 if ESP_CONSOLE_UART_CUSTOM_NUM_1
         default -1 if !ESP_CONSOLE_UART
@@ -309,7 +304,7 @@ menu "ESP System Settings"
     config ESP_CONSOLE_UART_TX_GPIO
         int "UART TX on GPIO#"
         depends on ESP_CONSOLE_UART_CUSTOM
-        range 0 46
+        range 0 SOC_GPIO_OUT_RANGE_MAX
         default 1 if IDF_TARGET_ESP32
         default 20 if IDF_TARGET_ESP32C2
         default 21 if IDF_TARGET_ESP32C3
@@ -327,7 +322,7 @@ menu "ESP System Settings"
     config ESP_CONSOLE_UART_RX_GPIO
         int "UART RX on GPIO#"
         depends on ESP_CONSOLE_UART_CUSTOM
-        range 0 46
+        range 0 SOC_GPIO_IN_RANGE_MAX
         default 3 if IDF_TARGET_ESP32
         default 19 if IDF_TARGET_ESP32C2
         default 20 if IDF_TARGET_ESP32C3

components/hal/esp32c2/include/hal/uart_ll.h

@@ -121,19 +121,6 @@ static inline void uart_ll_reset_register(uart_port_t uart_num)
 // SYSTEM.perip_rst_en0 is a shared register, so this function must be used in an atomic way
 #define uart_ll_reset_register(...) (void)__DECLARE_RCC_ATOMIC_ENV; uart_ll_reset_register(__VA_ARGS__)
 
-/**
- * @brief  Configure the UART core reset.
- *
- * @param  hw Beginning address of the peripheral registers.
- * @param  core_rst_en True to enable the core reset, otherwise set it false.
- *
- * @return None.
- */
-FORCE_INLINE_ATTR void uart_ll_set_reset_core(uart_dev_t *hw, bool core_rst_en)
-{
-    hw->clk_conf.rst_core = core_rst_en;
-}
-
 /**
  * @brief  Enable the UART clock.
  *

components/hal/esp32c3/include/hal/uart_ll.h

@@ -104,14 +104,19 @@ static inline void uart_ll_enable_bus_clock(uart_port_t uart_num, bool enable)
  */
 static inline void uart_ll_reset_register(uart_port_t uart_num)
 {
+    // ESP32C3 requires a workaround: enable core reset before enabling uart module clock to prevent uart output garbage value
     switch (uart_num) {
     case 0:
+        UART0.clk_conf.rst_core = 1;
         SYSTEM.perip_rst_en0.reg_uart_rst = 1;
         SYSTEM.perip_rst_en0.reg_uart_rst = 0;
+        UART0.clk_conf.rst_core = 0;
         break;
     case 1:
+        UART1.clk_conf.rst_core = 1;
         SYSTEM.perip_rst_en0.reg_uart1_rst = 1;
         SYSTEM.perip_rst_en0.reg_uart1_rst = 0;
+        UART1.clk_conf.rst_core = 0;
         break;
     default:
         abort();
@@ -121,19 +126,6 @@ static inline void uart_ll_reset_register(uart_port_t uart_num)
 // SYSTEM.perip_rst_enx are shared registers, so this function must be used in an atomic way
 #define uart_ll_reset_register(...) (void)__DECLARE_RCC_ATOMIC_ENV; uart_ll_reset_register(__VA_ARGS__)
 
-/**
- * @brief  Configure the UART core reset.
- *
- * @param  hw Beginning address of the peripheral registers.
- * @param  core_rst_en True to enable the core reset, otherwise set it false.
- *
- * @return None.
- */
-FORCE_INLINE_ATTR void uart_ll_set_reset_core(uart_dev_t *hw, bool core_rst_en)
-{
-    hw->clk_conf.rst_core = core_rst_en;
-}
-
 /**
  * @brief  Enable the UART clock.
  *

components/hal/esp32c6/include/hal/uart_ll.h

@@ -265,25 +265,6 @@ static inline void uart_ll_reset_register(uart_port_t uart_num)
     }
 }
 
-/**
- * @brief  Configure the UART core reset.
- *
- * @param  hw Beginning address of the peripheral registers.
- * @param  core_rst_en True to enable the core reset, otherwise set it false.
- *
- * @return None.
- */
-FORCE_INLINE_ATTR void uart_ll_set_reset_core(uart_dev_t *hw, bool core_rst_en)
-{
-    if ((hw) != &LP_UART) {
-        UART_LL_PCR_REG_SET(hw, conf, rst_en, core_rst_en);
-    } else {
-        // LP_UART reset shares the same register with other LP peripherals
-        // Needs to be protected with a lock, therefore, it has its unique LL function, and must be called from lp_periph_ctrl.c
-        abort();
-    }
-}
-
 /**
  * @brief  Enable the UART clock.
  *
@@ -297,7 +278,7 @@ FORCE_INLINE_ATTR void uart_ll_sclk_enable(uart_dev_t *hw)
         UART_LL_PCR_REG_SET(hw, sclk_conf, sclk_en, 1);
     } else {
         // LP_UART clk_en shares the same register with other LP peripherals
-        // Needs to be protected with a lock, therefore, it has its unique LL function, and must be called from lp_periph_ctrl.c
+        // Needs to be protected with a lock, therefore, it has its unique LL function
         abort();
     }
 }
@@ -315,7 +296,7 @@ FORCE_INLINE_ATTR void uart_ll_sclk_disable(uart_dev_t *hw)
         UART_LL_PCR_REG_SET(hw, sclk_conf, sclk_en, 0);
     } else {
         // LP_UART clk_en shares the same register with other LP peripherals
-        // Needs to be protected with a lock, therefore, it has its unique LL function, and must be called from lp_periph_ctrl.c
+        // Needs to be protected with a lock, therefore, it has its unique LL function
         abort();
     }
 }
@@ -350,7 +331,7 @@ FORCE_INLINE_ATTR void uart_ll_set_sclk(uart_dev_t *hw, soc_module_clk_t source_
         UART_LL_PCR_REG_SET(hw, sclk_conf, sclk_sel, sel_value);
     } else {
         // LP_UART clk_sel shares the same register with other LP peripherals
-        // Needs to be protected with a lock, therefore, it has its unique LL function, and must be called from lp_periph_ctrl.c
+        // Needs to be protected with a lock, therefore, it has its unique LL function
         abort();
     }
 }

components/hal/esp32h2/include/hal/uart_ll.h

@@ -154,19 +154,6 @@ FORCE_INLINE_ATTR void uart_ll_update(uart_dev_t *hw)
     while (hw->reg_update.reg_update);
 }
 
-/**
- * @brief  Configure the UART core reset.
- *
- * @param  hw Beginning address of the peripheral registers.
- * @param  core_rst_en True to enable the core reset, otherwise set it false.
- *
- * @return None.
- */
-FORCE_INLINE_ATTR void uart_ll_set_reset_core(uart_dev_t *hw, bool core_rst_en)
-{
-    UART_LL_PCR_REG_SET(hw, conf, rst_en, core_rst_en);
-}
-
 /**
  * @brief  Enable the UART clock.
  *

components/hal/esp32p4/include/hal/uart_ll.h

@@ -315,34 +315,6 @@ static inline void uart_ll_reset_register(uart_port_t uart_num)
 //  HP_SYS_CLKRST.hp_rst_en1 is a shared register, so this function must be used in an atomic way
 #define uart_ll_reset_register(...) (void)__DECLARE_RCC_ATOMIC_ENV; uart_ll_reset_register(__VA_ARGS__)
 
-/**
- * @brief  Configure the UART core reset.
- *
- * @param  hw Beginning address of the peripheral registers.
- * @param  core_rst_en True to enable the core reset, otherwise set it false.
- *
- * @return None.
- */
-FORCE_INLINE_ATTR void uart_ll_set_reset_core(uart_dev_t *hw, bool core_rst_en)
-{
-    if ((hw) == &UART0) {
-        HP_SYS_CLKRST.hp_rst_en1.reg_rst_en_uart0_core = core_rst_en;
-    } else if ((hw) == &UART1) {
-        HP_SYS_CLKRST.hp_rst_en1.reg_rst_en_uart1_core = core_rst_en;
-    } else if ((hw) == &UART2) {
-        HP_SYS_CLKRST.hp_rst_en1.reg_rst_en_uart2_core = core_rst_en;
-    } else if ((hw) == &UART3) {
-        HP_SYS_CLKRST.hp_rst_en1.reg_rst_en_uart3_core = core_rst_en;
-    } else if ((hw) == &UART4) {
-        HP_SYS_CLKRST.hp_rst_en1.reg_rst_en_uart4_core = core_rst_en;
-    } else {
-        // Not going to implement LP_UART reset in this function, it will have its own LL function
-        abort();
-    }
-}
-// HP_SYS_CLKRST.hp_rst_en1 is a shared register, so this function must be used in an atomic way
-#define uart_ll_set_reset_core(...) (void)__DECLARE_RCC_ATOMIC_ENV; uart_ll_set_reset_core(__VA_ARGS__)
-
 /**
  * @brief  Enable the UART clock.
  *

components/hal/esp32s3/include/hal/uart_ll.h

@@ -109,18 +109,25 @@ static inline void uart_ll_enable_bus_clock(uart_port_t uart_num, bool enable)
  */
 static inline void uart_ll_reset_register(uart_port_t uart_num)
 {
+    // ESP32S3 requires a workaround: enable core reset before enabling uart module clock to prevent uart output garbage value
     switch (uart_num) {
     case 0:
+        UART0.clk_conf.rst_core = 1;
         SYSTEM.perip_rst_en0.uart_rst = 1;
         SYSTEM.perip_rst_en0.uart_rst = 0;
+        UART0.clk_conf.rst_core = 0;
         break;
     case 1:
+        UART1.clk_conf.rst_core = 1;
         SYSTEM.perip_rst_en0.uart1_rst = 1;
         SYSTEM.perip_rst_en0.uart1_rst = 0;
+        UART1.clk_conf.rst_core = 0;
         break;
     case 2:
+        UART2.clk_conf.rst_core = 1;
         SYSTEM.perip_rst_en1.uart2_rst = 1;
         SYSTEM.perip_rst_en1.uart2_rst = 0;
+        UART2.clk_conf.rst_core = 0;
         break;
     default:
         abort();
@@ -130,19 +137,6 @@ static inline void uart_ll_reset_register(uart_port_t uart_num)
 // SYSTEM.perip_rst_enx are shared registers, so this function must be used in an atomic way
 #define uart_ll_reset_register(...) (void)__DECLARE_RCC_ATOMIC_ENV; uart_ll_reset_register(__VA_ARGS__)
 
-/**
- * @brief  Configure the UART core reset.
- *
- * @param  hw Beginning address of the peripheral registers.
- * @param  core_rst_en True to enable the core reset, otherwise set it false.
- *
- * @return None.
- */
-static inline void uart_ll_set_reset_core(uart_dev_t *hw, bool core_rst_en)
-{
-    hw->clk_conf.rst_core = core_rst_en;
-}
-
 /**
  * @brief  Set the UART source clock.
  *

components/hal/include/hal/uart_hal.h

@@ -145,16 +145,6 @@ typedef struct {
  */
 #define uart_hal_is_tx_idle(hal)  uart_ll_is_tx_idle((hal)->dev)
 
-/**
- * @brief  Configure the UART core reset
- *
- * @param  hal Context of the HAL layer
- * @param  core_rst_en true to enable the core reset, otherwise set it false
- *
- * @return None
- */
-#define uart_hal_set_reset_core(hal, core_rst_en)  uart_ll_set_reset_core((hal)->dev, core_rst_en)
-
 /**
  * @brief  Read data from the UART rxfifo
  *

components/soc/esp32/include/soc/Kconfig.soc_caps.in

@@ -311,6 +311,14 @@ config SOC_GPIO_VALID_GPIO_MASK
     hex
     default 0xFFFFFFFFFF
 
+config SOC_GPIO_IN_RANGE_MAX
+    int
+    default 39
+
+config SOC_GPIO_OUT_RANGE_MAX
+    int
+    default 33
+
 config SOC_GPIO_VALID_DIGITAL_IO_PAD_MASK
     hex
     default 0xEF0FEA

components/soc/esp32/include/soc/soc_caps.h

@@ -178,6 +178,9 @@
 // GPIO >= 34 are input only
 #define SOC_GPIO_VALID_OUTPUT_GPIO_MASK (SOC_GPIO_VALID_GPIO_MASK & ~(0ULL | BIT34 | BIT35 | BIT36 | BIT37 | BIT38 | BIT39))
 
+#define SOC_GPIO_IN_RANGE_MAX           39
+#define SOC_GPIO_OUT_RANGE_MAX          33
+
 // digital I/O pad powered by VDD3P3_CPU or VDD_SPI(GPIO_NUM: 1, 3, 5, 6, 7, 8, 9, 10, 11, 16, 17, 18, 19, 21, 22, 23)
 #define SOC_GPIO_VALID_DIGITAL_IO_PAD_MASK 0xEF0FEAULL
 

components/soc/esp32c2/include/soc/Kconfig.soc_caps.in

@@ -271,6 +271,14 @@ config SOC_GPIO_SUPPORT_DEEPSLEEP_WAKEUP
     bool
     default y
 
+config SOC_GPIO_IN_RANGE_MAX
+    int
+    default 20
+
+config SOC_GPIO_OUT_RANGE_MAX
+    int
+    default 20
+
 config SOC_GPIO_DEEP_SLEEP_WAKE_VALID_GPIO_MASK
     int
     default 0

components/soc/esp32c2/include/soc/soc_caps.h

@@ -131,6 +131,10 @@
 
 #define SOC_GPIO_VALID_GPIO_MASK        ((1U<<SOC_GPIO_PIN_COUNT) - 1)
 #define SOC_GPIO_VALID_OUTPUT_GPIO_MASK SOC_GPIO_VALID_GPIO_MASK
+
+#define SOC_GPIO_IN_RANGE_MAX           20
+#define SOC_GPIO_OUT_RANGE_MAX          20
+
 #define SOC_GPIO_DEEP_SLEEP_WAKE_VALID_GPIO_MASK        (0ULL | BIT0 | BIT1 | BIT2 | BIT3 | BIT4 | BIT5)
 
 // digital I/O pad powered by VDD3P3_CPU or VDD_SPI(GPIO_NUM_6~GPIO_NUM_20)

components/soc/esp32c3/include/soc/Kconfig.soc_caps.in

@@ -363,6 +363,14 @@ config SOC_GPIO_SUPPORT_DEEPSLEEP_WAKEUP
     bool
     default y
 
+config SOC_GPIO_IN_RANGE_MAX
+    int
+    default 21
+
+config SOC_GPIO_OUT_RANGE_MAX
+    int
+    default 21
+
 config SOC_GPIO_DEEP_SLEEP_WAKE_VALID_GPIO_MASK
     int
     default 0
@@ -907,10 +915,6 @@ config SOC_UART_SUPPORT_WAKEUP_INT
     bool
     default y
 
-config SOC_UART_REQUIRE_CORE_RESET
-    bool
-    default y
-
 config SOC_UART_SUPPORT_FSM_TX_WAIT_SEND
     bool
     default y

components/soc/esp32c3/include/soc/soc_caps.h

@@ -169,6 +169,10 @@
 
 #define SOC_GPIO_VALID_GPIO_MASK        ((1U<<SOC_GPIO_PIN_COUNT) - 1)
 #define SOC_GPIO_VALID_OUTPUT_GPIO_MASK SOC_GPIO_VALID_GPIO_MASK
+
+#define SOC_GPIO_IN_RANGE_MAX           21
+#define SOC_GPIO_OUT_RANGE_MAX          21
+
 #define SOC_GPIO_DEEP_SLEEP_WAKE_VALID_GPIO_MASK        (0ULL | BIT0 | BIT1 | BIT2 | BIT3 | BIT4 | BIT5)
 
 // digital I/O pad powered by VDD3P3_CPU or VDD_SPI(GPIO_NUM_6~GPIO_NUM_21)
@@ -392,7 +396,6 @@
 #define SOC_UART_SUPPORT_RTC_CLK    (1)     /*!< Support RTC clock as the clock source */
 #define SOC_UART_SUPPORT_XTAL_CLK   (1)     /*!< Support XTAL clock as the clock source */
 #define SOC_UART_SUPPORT_WAKEUP_INT (1)         /*!< Support UART wakeup interrupt */
-#define SOC_UART_REQUIRE_CORE_RESET (1)
 
 // UART has an extra TX_WAIT_SEND state when the FIFO is not empty and XOFF is enabled
 #define SOC_UART_SUPPORT_FSM_TX_WAIT_SEND   (1)

components/soc/esp32c6/include/soc/Kconfig.soc_caps.in

@@ -459,6 +459,14 @@ config SOC_GPIO_SUPPORT_DEEPSLEEP_WAKEUP
     bool
     default y
 
+config SOC_GPIO_IN_RANGE_MAX
+    int
+    default 30
+
+config SOC_GPIO_OUT_RANGE_MAX
+    int
+    default 30
+
 config SOC_GPIO_DEEP_SLEEP_WAKE_VALID_GPIO_MASK
     int
     default 0

components/soc/esp32c6/include/soc/soc_caps.h

@@ -198,6 +198,10 @@
 
 #define SOC_GPIO_VALID_GPIO_MASK        ((1U<<SOC_GPIO_PIN_COUNT) - 1)
 #define SOC_GPIO_VALID_OUTPUT_GPIO_MASK SOC_GPIO_VALID_GPIO_MASK
+
+#define SOC_GPIO_IN_RANGE_MAX           30
+#define SOC_GPIO_OUT_RANGE_MAX          30
+
 #define SOC_GPIO_DEEP_SLEEP_WAKE_VALID_GPIO_MASK        (0ULL | BIT0 | BIT1 | BIT2 | BIT3 | BIT4 | BIT5 | BIT6 | BIT7)
 
 // digital I/O pad powered by VDD3P3_CPU or VDD_SPI(GPIO_NUM_8~GPIO_NUM_30)

components/soc/esp32h2/include/soc/Kconfig.soc_caps.in

@@ -463,6 +463,14 @@ config SOC_GPIO_SUPPORT_RTC_INDEPENDENT
     bool
     default y
 
+config SOC_GPIO_IN_RANGE_MAX
+    int
+    default 27
+
+config SOC_GPIO_OUT_RANGE_MAX
+    int
+    default 27
+
 config SOC_GPIO_VALID_DIGITAL_IO_PAD_MASK
     hex
     default 0x000000000FFF807F

components/soc/esp32h2/include/soc/soc_caps.h

@@ -204,6 +204,9 @@
 #define SOC_GPIO_VALID_GPIO_MASK        ((1U << SOC_GPIO_PIN_COUNT) - 1)
 #define SOC_GPIO_VALID_OUTPUT_GPIO_MASK SOC_GPIO_VALID_GPIO_MASK
 
+#define SOC_GPIO_IN_RANGE_MAX           27
+#define SOC_GPIO_OUT_RANGE_MAX          27
+
 // digital I/O pad powered by VDD3P3_CPU or VDD_SPI(GPIO_NUM_0~6. GPIO_NUM_15~27)
 #define SOC_GPIO_VALID_DIGITAL_IO_PAD_MASK 0x000000000FFF807FULL
 

components/soc/esp32p4/include/soc/Kconfig.soc_caps.in

@@ -395,6 +395,14 @@ config SOC_GPIO_VALID_GPIO_MASK
     hex
     default 0x01FFFFFFFFFFFFFF
 
+config SOC_GPIO_IN_RANGE_MAX
+    int
+    default 56
+
+config SOC_GPIO_OUT_RANGE_MAX
+    int
+    default 56
+
 config SOC_GPIO_DEEP_SLEEP_WAKE_VALID_GPIO_MASK
     int
     default 0

components/soc/esp32p4/include/soc/soc_caps.h

@@ -204,6 +204,10 @@
 
 #define SOC_GPIO_VALID_GPIO_MASK        (0x01FFFFFFFFFFFFFF)
 #define SOC_GPIO_VALID_OUTPUT_GPIO_MASK SOC_GPIO_VALID_GPIO_MASK
+
+#define SOC_GPIO_IN_RANGE_MAX           56
+#define SOC_GPIO_OUT_RANGE_MAX          56
+
 #define SOC_GPIO_DEEP_SLEEP_WAKE_VALID_GPIO_MASK        (0ULL | 0xFFFF)
 
 // digital I/O pad powered by VDD3P3_CPU or VDD_SPI(GPIO_NUM_16~GPIO_NUM_56)

components/soc/esp32s2/include/soc/Kconfig.soc_caps.in

@@ -363,6 +363,14 @@ config SOC_GPIO_VALID_GPIO_MASK
     hex
     default 0x7FFFFFFFFFFF
 
+config SOC_GPIO_IN_RANGE_MAX
+    int
+    default 46
+
+config SOC_GPIO_OUT_RANGE_MAX
+    int
+    default 45
+
 config SOC_GPIO_VALID_DIGITAL_IO_PAD_MASK
     hex
     default 0x00007FFFFC000000

components/soc/esp32s2/include/soc/soc_caps.h

@@ -168,6 +168,9 @@
 // GPIO 46 is input only
 #define SOC_GPIO_VALID_OUTPUT_GPIO_MASK     (SOC_GPIO_VALID_GPIO_MASK & ~(0ULL | BIT46))
 
+#define SOC_GPIO_IN_RANGE_MAX           46
+#define SOC_GPIO_OUT_RANGE_MAX          45
+
 // digital I/O pad powered by VDD3P3_CPU or VDD_SPI(GPIO_NUM_26~GPIO_NUM_46)
 #define SOC_GPIO_VALID_DIGITAL_IO_PAD_MASK  0x00007FFFFC000000ULL
 

components/soc/esp32s3/include/soc/Kconfig.soc_caps.in

@@ -431,6 +431,14 @@ config SOC_GPIO_VALID_GPIO_MASK
     hex
     default 0x1FFFFFFFFFFFF
 
+config SOC_GPIO_IN_RANGE_MAX
+    int
+    default 48
+
+config SOC_GPIO_OUT_RANGE_MAX
+    int
+    default 48
+
 config SOC_GPIO_VALID_DIGITAL_IO_PAD_MASK
     hex
     default 0x0001FFFFFC000000
@@ -967,10 +975,6 @@ config SOC_UART_SUPPORT_XTAL_CLK
     bool
     default y
 
-config SOC_UART_REQUIRE_CORE_RESET
-    bool
-    default y
-
 config SOC_USB_PERIPH_NUM
     bool
     default y

components/soc/esp32s3/include/soc/soc_caps.h

@@ -174,6 +174,10 @@
 #define SOC_GPIO_VALID_GPIO_MASK         (0x1FFFFFFFFFFFFULL & ~(0ULL | BIT22 | BIT23 | BIT24 | BIT25))
 // No GPIO is input only
 #define SOC_GPIO_VALID_OUTPUT_GPIO_MASK  (SOC_GPIO_VALID_GPIO_MASK)
+
+#define SOC_GPIO_IN_RANGE_MAX            48
+#define SOC_GPIO_OUT_RANGE_MAX           48
+
 // digital I/O pad powered by VDD3P3_CPU or VDD_SPI(GPIO_NUM_26~GPIO_NUM_48)
 #define SOC_GPIO_VALID_DIGITAL_IO_PAD_MASK 0x0001FFFFFC000000ULL
 
@@ -380,7 +384,6 @@
 #define SOC_UART_SUPPORT_APB_CLK    (1)     /*!< Support APB as the clock source */
 #define SOC_UART_SUPPORT_RTC_CLK    (1)     /*!< Support RTC clock as the clock source */
 #define SOC_UART_SUPPORT_XTAL_CLK   (1)     /*!< Support XTAL clock as the clock source */
-#define SOC_UART_REQUIRE_CORE_RESET (1)
 
 /*-------------------------- USB CAPS ----------------------------------------*/
 #define SOC_USB_PERIPH_NUM 1

components/soc/linux/include/soc/Kconfig.soc_caps.in

@@ -2,3 +2,11 @@
 # This file is auto-generated from SoC caps
 # using gen_soc_caps_kconfig.py, do not edit manually
 #####################################################
+
+config SOC_GPIO_IN_RANGE_MAX
+    int
+    default 65535
+
+config SOC_GPIO_OUT_RANGE_MAX
+    int
+    default 65535

components/soc/linux/include/soc/soc_caps.h

@@ -1,5 +1,5 @@
 /*
- * SPDX-FileCopyrightText: 2022 Espressif Systems (Shanghai) CO LTD
+ * SPDX-FileCopyrightText: 2022-2023 Espressif Systems (Shanghai) CO LTD
  *
  * SPDX-License-Identifier: Apache-2.0
  */
@@ -23,3 +23,7 @@
 */
 
 #pragma once
+
+// No meaning to define GPIO number for Linux target, only to avoid build warning on Kconfig ESP_CONSOLE_UART_TX_GPIO, ESP_CONSOLE_UART_RX_GPIO
+#define SOC_GPIO_IN_RANGE_MAX           (65535)
+#define SOC_GPIO_OUT_RANGE_MAX          (65535)