diff --git a/examples/openthread/ot_br/README.md b/examples/openthread/ot_br/README.md index 953c4c3bd7..f864976500 100644 --- a/examples/openthread/ot_br/README.md +++ b/examples/openthread/ot_br/README.md @@ -18,13 +18,13 @@ The ESP Thread Border Router SDK provides extra components and examples for putt #### **Wi-Fi based Thread Border Router** By default, two SoCs are required to run this example: * An ESP32 series Wi-Fi SoC (ESP32, ESP32-C, ESP32-S, etc) loaded with this ot_br example. -* An ESP32-H4 802.15.4 SoC loaded with [ot_rcp](../ot_rcp) example. -* Another ESP32-H4 SoC loaded with [ot_cli](../ot_cli) example. +* An ESP32-H2 802.15.4 SoC loaded with [ot_rcp](../ot_rcp) example. +* Another ESP32-H2 SoC loaded with [ot_cli](../ot_cli) example. -Connect the two SoCs via UART, below is an example setup with ESP32 DevKitC and ESP32-H4 DevKitC: -![thread_br](image/thread-border-router-esp32-esp32h4.jpg) +Connect the two SoCs via UART, below is an example setup with ESP32 DevKitC and ESP32-H2 DevKitC: +![thread_br](image/thread-border-router-esp32-esp32h2.jpg) -ESP32 pin | ESP32-H4 pin +ESP32 pin | ESP32-H2 pin ----------|------------- GND | G GPIO4 | TX diff --git a/examples/openthread/ot_br/image/thread-border-router-esp32-esp32h4.jpg b/examples/openthread/ot_br/image/thread-border-router-esp32-esp32h2.jpg similarity index 100% rename from examples/openthread/ot_br/image/thread-border-router-esp32-esp32h4.jpg rename to examples/openthread/ot_br/image/thread-border-router-esp32-esp32h2.jpg diff --git a/examples/openthread/ot_cli/README.md b/examples/openthread/ot_cli/README.md index 1c53acf0da..917c4b1b9e 100644 --- a/examples/openthread/ot_cli/README.md +++ b/examples/openthread/ot_cli/README.md @@ -9,7 +9,7 @@ This example demonstrates an [OpenThread CLI](https://github.com/openthread/open ### Hardware Required -To run this example, an ESP32-H4 board is required. +To run this example, an ESP32-H2 board is required. ### Configure the project @@ -63,7 +63,7 @@ factoryreset ## Set Up Network -To run this example, at least two ESP32-H4 boards flashed with this ot_cli example are required. +To run this example, at least two ESP32-H2 boards flashed with this ot_cli example are required. On the first device, run the following commands: ```bash diff --git a/examples/openthread/ot_rcp/README.md b/examples/openthread/ot_rcp/README.md index fff79a198a..d241c3d905 100644 --- a/examples/openthread/ot_rcp/README.md +++ b/examples/openthread/ot_rcp/README.md @@ -13,11 +13,11 @@ OpenThread RCP doesn't function alone, it needs to work together with a Host and ### Hardware Required -To run this example, an ESP32-H4 board is required. +To run this example, an ESP32-H2 board is required. ### Configure the project -The default communication interface is port 0 of ESP32-H4 UART running at 115200 baud, change the configuration in [esp_ot_config.h](main/esp_ot_config.h) if you want to use another interface or need different communication parameters. +The default communication interface is port 0 of ESP32-H2 UART running at 460800 baud, change the configuration in [esp_ot_config.h](main/esp_ot_config.h) if you want to use another interface or need different communication parameters. ### Build and Flash diff --git a/examples/zigbee/esp_zigbee_gateway/README.md b/examples/zigbee/esp_zigbee_gateway/README.md index d2c2e17f2b..40aa4be56b 100644 --- a/examples/zigbee/esp_zigbee_gateway/README.md +++ b/examples/zigbee/esp_zigbee_gateway/README.md @@ -3,19 +3,20 @@ # Gateway Example -This example demonstrates how to build a Zigbee Gateway device. It runs on a Wi-Fi SoC such as ESP32, ESP32-C3 and ESP32-S3, with an 802.15.4 SoC like ESP32-H2 running [esp_zigbee_rcp](../esp_zigbee_rcp) to provide 802.15.4 radio. +This example demonstrates how to build a Zigbee Gateway device. -The example could also run on a single SoC which supports both Wi-Fi and Zigbee (e.g., ESP32-C6), but since there is only one RF path in ESP32-C6, which means Wi-Fi and Zigbee can't receive simultaneously, it has a significant impact on performance. Hence the two SoCs solution is recommended. +The ESP Zigbee SDK provides more examples and tools for productization: +* [ESP Zigbee SDK Docs](https://docs.espressif.com/projects/esp-zigbee-sdk) +* [ESP Zigbee SDK Repo](https://github.com/espressif/esp-zigbee-sdk) ## Hardware Required -* One development board with ESP32 or ESP32-S3 SoC acting as Zigbee gateway (loaded with esp_zigbee_gateway example) -* A USB cable for power supply and programming -* Three jumper wires for UART (TX, RX and GND) -* Gateway doesn't function alone. Choose ESP32-H2 as Zigbee rcp (see [esp_zigbee_rcp example](../esp_zigbee_rcp)) -* **Flash** Zigbee rcp on the ESP32-H2 DevKitC first **before** connecting to Zigbee gateway -* Connect the two SoCs via UART, below is an example setup with ESP32-DevKitC and ESP32-H2-DevKitC: -![Zigbee_gateway](../../openthread/ot_br/image/thread-border-router-esp32-esp32h4.jpg) +By default, two SoCs are required to run this example: +* An ESP32 series Wi-Fi SoC (ESP32, ESP32-C, ESP32-S, etc) loaded with this esp_zigbee_gateway example. +* An ESP32-H2 802.15.4 SoC loaded with [esp_zigbee_rcp](../esp_zigbee_rcp) example + +Connect the two SoCs via UART, below is an example setup with ESP32-DevKitC and ESP32-H2-DevKitC: +![Zigbee_gateway](../../openthread/ot_br/image/thread-border-router-esp32-esp32h2.jpg) ESP32 pin | ESP32-H2 pin ------------- |------------- @@ -25,9 +26,13 @@ ESP32 pin | ESP32-H2 pin * TX, RX pin can be also configured by user in esp_zigbee_gateway.h +The example could also run on a single SoC which supports both Wi-Fi and Zigbee (e.g., ESP32-C6), but since there is only one RF path in ESP32-C6, which means Wi-Fi and Zigbee can't receive simultaneously, it has a significant impact on performance. Hence the two SoCs solution is recommended. + ## Configure the project -Before project configuration and build, make sure to set the correct chip target using `idf.py set-target esp32` or `idf.py set-target esp32s3` +Before project configuration and build, make sure to set the correct chip target using `idf.py set-target `. + +In order to run the example on single SoC which supports both Wi-Fi and Thread, the option `CONFIG_ESP_COEX_SW_COEXIST_ENABLE` and option `CONFIG_ZB_RADIO_NATIVE` should be enabled. The two options are enabled by default for ESP32-C6 target. ## Erase the NVRAM diff --git a/examples/zigbee/esp_zigbee_rcp/README.md b/examples/zigbee/esp_zigbee_rcp/README.md index ba98d6d410..a930b7fc81 100644 --- a/examples/zigbee/esp_zigbee_rcp/README.md +++ b/examples/zigbee/esp_zigbee_rcp/README.md @@ -1,5 +1,5 @@ -| Supported Targets | ESP32-C6 | ESP32-H2 | ESP32-H4 | -| ----------------- | -------- | -------- | -------- | +| Supported Targets | ESP32-C6 | ESP32-H2 | +| ----------------- | -------- | -------- | # Rcp Example @@ -7,7 +7,7 @@ This test code shows how to configure Zigbee rcp (radio co-processor) device. Rc ## Hardware Required -* One development board with ESP32-H4 SoC acting as Zigbee rcp (loaded with esp_zigbee_rcp example) +* One development board with ESP32-H2 SoC acting as Zigbee rcp (loaded with esp_zigbee_rcp example) * A USB cable for power supply and programming * Choose ESP32 or ESP32-S3 as Zigbee gateway. The connection and setup refer to the Zigbee gateway example for setup details (see [esp_zigbee_gateway example](../esp_zigbee_gateway)) * TX, RX pin can be also configured by user in esp_zigbee_rcp.h diff --git a/examples/zigbee/light_sample/HA_on_off_light/README.md b/examples/zigbee/light_sample/HA_on_off_light/README.md index 2f481ee1aa..28eaf8d327 100644 --- a/examples/zigbee/light_sample/HA_on_off_light/README.md +++ b/examples/zigbee/light_sample/HA_on_off_light/README.md @@ -1,15 +1,19 @@ -| Supported Targets | ESP32-C6 | ESP32-H2 | ESP32-H4 | -| ----------------- | -------- | -------- | -------- | +| Supported Targets | ESP32-C6 | ESP32-H2 | +| ----------------- | -------- | -------- | # Light Bulb Example -This test code shows how to configure Zigbee end device and use it as HA on/off light bulb +This test code shows how to configure Zigbee end device and use it as HA on/off light bulb. + +The ESP Zigbee SDK provides more examples and tools for productization: +* [ESP Zigbee SDK Docs](https://docs.espressif.com/projects/esp-zigbee-sdk) +* [ESP Zigbee SDK Repo](https://github.com/espressif/esp-zigbee-sdk) ## Hardware Required -* One development board with ESP32-H4 SoC acting as Zigbee end device (loaded with HA_on_off_light example) +* One development board with ESP32-H2 SoC acting as Zigbee end device (loaded with HA_on_off_light example) * A USB cable for power supply and programming -* Choose another ESP32-H4 as Zigbee coordinator (see [HA_on_off_switch example](../HA_on_off_switch)) +* Choose another ESP32-H2 as Zigbee coordinator (see [HA_on_off_switch example](../HA_on_off_switch)) ## Configure the project @@ -45,7 +49,7 @@ I (9671) ESP_ZB_LIGHT: on/off light set to 0 ## Light Control Functions - * By toggling the switch button (BOOT) on the ESP32-H4 board loaded with the `HA_on_off_switch` example, the LED on this board loaded with `HA_on_off_light` example will be on and off. + * By toggling the switch button (BOOT) on the ESP32-H2 board loaded with the `HA_on_off_switch` example, the LED on this board loaded with `HA_on_off_light` example will be on and off. ## Troubleshooting diff --git a/examples/zigbee/light_sample/HA_on_off_switch/README.md b/examples/zigbee/light_sample/HA_on_off_switch/README.md index 761486a733..2b5ffc21e1 100644 --- a/examples/zigbee/light_sample/HA_on_off_switch/README.md +++ b/examples/zigbee/light_sample/HA_on_off_switch/README.md @@ -1,15 +1,19 @@ -| Supported Targets | ESP32-C6 | ESP32-H2 | ESP32-H4 | -| ----------------- | -------- | -------- | -------- | +| Supported Targets | ESP32-C6 | ESP32-H2 | +| ----------------- | -------- | -------- | # Light Switch Example -This test code shows how to configure Zigbee Coordinator and use it as an HA on/off_switch +This test code shows how to configure Zigbee Coordinator and use it as an HA on/off_switch. + +The ESP Zigbee SDK provides more examples and tools for productization: +* [ESP Zigbee SDK Docs](https://docs.espressif.com/projects/esp-zigbee-sdk) +* [ESP Zigbee SDK Repo](https://github.com/espressif/esp-zigbee-sdk) ## Hardware Required -* One development board with ESP32-H4 SoC acting as Zigbee Coordinator (loaded with HA_on_off_switch) +* One development board with ESP32-H2 SoC acting as Zigbee Coordinator (loaded with HA_on_off_switch) * A USB cable for power supply and programming -* Choose another ESP32-H4 as Zigbee end-device (see [HA_on_off_light](../HA_on_off_light/)) +* Choose another ESP32-H2 as Zigbee end-device (see [HA_on_off_light](../HA_on_off_light/)) ## Configure the project