esp-idf/docs/en/get-started-cmake/get-started-pico-kit-v3.rst

78 lines
3.8 KiB
ReStructuredText
Raw Normal View History

ESP32-PICO-KIT V3 Getting Started Guide (CMake)
===============================================
2019-03-26 04:11:11 -04:00
:link_to_translation:`zh_CN:[中文]`
2019-03-26 04:11:11 -04:00
This guide shows how to get started with the ESP32-PICO-KIT V3 mini development board. For the description of other ESP32-PICO-KIT versions, please check :doc:`../hw-reference/index`.
What You Need
-------------
2019-03-26 04:11:11 -04:00
* ESP32-PICO-KIT V3 mini development board
* USB 2.0 A to Micro B cable
* Computer running Windows, Linux, or macOS
2019-03-26 04:11:11 -04:00
You can skip the introduction sections and go directly to Section `Start Application Development`_.
Overview
--------
2019-03-26 04:11:11 -04:00
ESP32-PICO-KIT V3 is an ESP32-based mini development board produced by `Espressif <https://espressif.com>`_. The core of this board is ESP32-PICO-D4 - a System-in-Package (SiP) module.
The development board features a USB-UART Bridge circuit, which allows developers to connect the board to a computer's USB port for flashing and debugging.
All the IO signals and system power on ESP32-PICO-D4 are led out to two rows of 20 x 0.1" header pads on both sides of the development board for easy access.
Functional Description
----------------------
2019-03-26 04:11:11 -04:00
The following figure and the table below describe the key components, interfaces, and controls of the ESP32-PICO-KIT V3 board.
.. figure:: ../../_static/esp32-pico-kit-v3-layout.jpg
:align: center
:alt: ESP32-PICO-KIT V3 board layout
:figclass: align-center
ESP32-PICO-KIT V3 board layout
2019-03-26 04:11:11 -04:00
Below is the description of the items identified in the figure starting from the top left corner and going clockwise.
================== =================================================================================================================================
Key Component Description
================== =================================================================================================================================
ESP32-PICO-D4 Standard ESP32-PICO-D4 module soldered to the ESP32-PICO-KIT V3 board. The complete ESP32 system on a chip (ESP32 SoC) has been integrated into the SiP module, requiring only an external antenna with LC matching network, decoupling capacitors, and a pull-up resistor for EN signals to function properly.
LDO 5V-to-3.3V Low dropout voltage regulator (LDO).
USB-UART bridge Single-chip USB-UART bridge provides up to 1 Mbps transfers rates.
Micro USB Port USB interface. Power supply for the board as well as the communication interface between a computer and the board.
Power On LED This red LED turns on when power is supplied to the board.
I/O All the pins on ESP32-PICO-D4 are broken out to pin headers. You can program ESP32 to enable multiple functions, such as PWM, ADC, DAC, I2C, I2S, SPI, etc.
BOOT Button Download button. Holding down **Boot** and then pressing **EN** initiates Firmware Download mode for downloading firmware through the serial port.
EN Button Reset button.
================== =================================================================================================================================
Start Application Development
-----------------------------
Before powering up your ESP32-PICO-KIT V3, please make sure that the board is in good condition with no obvious signs of damage.
After that, proceed to :doc:`index`, where Section :ref:`get-started-step-by-step-cmake` will quickly help you set up the development environment and then flash an example project onto your board.
Related Documents
-----------------
* `ESP32-PICO-KIT V3 schematic <https://dl.espressif.com/dl/schematics/esp32-pico-kit-v3_schematic.pdf>`_ (PDF)
* `ESP32-PICO-D4 Datasheet <http://espressif.com/sites/default/files/documentation/esp32-pico-d4_datasheet_en.pdf>`_ (PDF)
* :doc:`../hw-reference/index`