mirror of
https://github.com/espressif/esp-idf.git
synced 2024-10-05 20:47:46 -04:00
195 lines
6.3 KiB
Plaintext
195 lines
6.3 KiB
Plaintext
|
menu "Performance Benchmark Example Configuration"
|
||
|
|
|
||
|
|
config EXAMPLE_USE_MEGABYTES
|
||
|
|
bool "Use megabytes instead of megabits"
|
||
|
|
default y
|
||
|
|
help
|
||
|
|
If this config item is set, the IO speed will be displayed in megabytes per second
|
||
|
|
instead of megabits per second.
|
||
|
|
|
||
|
|
config EXAMPLE_TEST_SPIFLASH
|
||
|
|
bool "Test internal SPI flash"
|
||
|
|
default y
|
||
|
|
help
|
||
|
|
If this config item is set, the internal SPI flash will be tested.
|
||
|
|
|
||
|
|
menu "Internal flash test config"
|
||
|
|
depends on EXAMPLE_TEST_SPIFLASH
|
||
|
|
|
||
|
|
config EXAMPLE_TEST_SPIFLASH_RAW
|
||
|
|
bool "Test raw access"
|
||
|
|
default y
|
||
|
|
help
|
||
|
|
If this config item is set, raw access will be tested.
|
||
|
|
|
||
|
|
config EXAMPLE_TEST_SPIFLASH_FATFS
|
||
|
|
bool "Test FATFS"
|
||
|
|
default y
|
||
|
|
help
|
||
|
|
If this config item is set, FATFS will be tested.
|
||
|
|
|
||
|
|
config EXAMPLE_TEST_SPIFLASH_SPIFFS
|
||
|
|
bool "Test SPIFFS"
|
||
|
|
default y
|
||
|
|
help
|
||
|
|
If this config item is set, SPIFFS will be tested.
|
||
|
|
|
||
|
|
endmenu # "Internal flash test config"
|
||
|
|
|
||
|
|
config EXAMPLE_TEST_SD_CARD
|
||
|
|
bool "Test SD card"
|
||
|
|
default y
|
||
|
|
help
|
||
|
|
If this config item is set, the SD card will be tested after it is mounted.
|
||
|
|
|
||
|
|
choice EXAMPLE_SD_CARD_INTERFACE
|
||
|
|
prompt "SD card interface"
|
||
|
|
depends on EXAMPLE_TEST_SD_CARD
|
||
|
|
default EXAMPLE_USE_SDMMC if SOC_SDMMC_HOST_SUPPORTED
|
||
|
|
default EXAMPLE_USE_SDSPI if !SOC_SDMMC_HOST_SUPPORTED
|
||
|
|
help
|
||
|
|
Select the SD card interface.
|
||
|
|
|
||
|
|
if SOC_SDMMC_HOST_SUPPORTED
|
||
|
|
config EXAMPLE_USE_SDMMC
|
||
|
|
bool "SDMMC"
|
||
|
|
endif # SOC_SDMMC_HOST_SUPPORTED
|
||
|
|
|
||
|
|
config EXAMPLE_USE_SDSPI
|
||
|
|
bool "SDSPI"
|
||
|
|
endchoice # EXAMPLE_SD_CARD_INTERFACE
|
||
|
|
|
||
|
|
menu "SD card test config"
|
||
|
|
depends on EXAMPLE_TEST_SD_CARD
|
||
|
|
|
||
|
|
config EXAMPLE_TEST_SD_CARD_RAW
|
||
|
|
bool "Test raw access"
|
||
|
|
default y
|
||
|
|
help
|
||
|
|
If this config item is set, raw access will be tested.
|
||
|
|
|
||
|
|
config EXAMPLE_TEST_SD_CARD_FATFS
|
||
|
|
bool "Test FATFS"
|
||
|
|
default y
|
||
|
|
help
|
||
|
|
If this config item is set, FATFS will be tested.
|
||
|
|
|
||
|
|
choice EXAMPLE_SD_CARD_FREQ_PICKER
|
||
|
|
prompt "SD card frequency"
|
||
|
|
default EXAMPLE_SD_FREQ_HIGHSPEED if EXAMPLE_USE_SDMMC
|
||
|
|
default EXAMPLE_SD_FREQ_DEFAULT if EXAMPLE_USE_SDSPI
|
||
|
|
help
|
||
|
|
Select the frequency of SD card interface.
|
||
|
|
|
||
|
|
config EXAMPLE_SD_FREQ_PROBING
|
||
|
|
bool "Probing frequency (400kHz)"
|
||
|
|
|
||
|
|
config EXAMPLE_SD_FREQ_DEFAULT
|
||
|
|
bool "Default frequency (20MHz)"
|
||
|
|
|
||
|
|
config EXAMPLE_SD_FREQ_HIGHSPEED
|
||
|
|
bool "High speed frequency (40MHz)"
|
||
|
|
depends on EXAMPLE_USE_SDMMC
|
||
|
|
|
||
|
|
config EXAMPLE_SD_FREQ_CUSTOM
|
||
|
|
bool "Custom frequency"
|
||
|
|
endchoice # EXAMPLE_SD_CARD_FREQ_PICKER
|
||
|
|
|
||
|
|
config EXAMPLE_SD_FREQ_CUSTOM_VAL
|
||
|
|
int "Custom frequency (kHz)"
|
||
|
|
default 20000
|
||
|
|
depends on EXAMPLE_SD_FREQ_CUSTOM
|
||
|
|
help
|
||
|
|
Enter the custom frequency of SD card interface.
|
||
|
|
|
||
|
|
if EXAMPLE_USE_SDMMC
|
||
|
|
|
||
|
|
choice EXAMPLE_SDMMC_BUS_WIDTH
|
||
|
|
prompt "SD/MMC bus width"
|
||
|
|
help
|
||
|
|
Select the bus width of SD or MMC interface.
|
||
|
|
Note that even if 1 line mode is used,
|
||
|
|
D3 pin of the SD card must have a pull-up resistor connected.
|
||
|
|
Otherwise the card may enter SPI mode,
|
||
|
|
the only way to recover from which is to cycle power to the card.
|
||
|
|
|
||
|
|
config EXAMPLE_SDMMC_BUS_WIDTH_4
|
||
|
|
bool "4 lines (D0 - D3)"
|
||
|
|
|
||
|
|
config EXAMPLE_SDMMC_BUS_WIDTH_1
|
||
|
|
bool "1 line (D0)"
|
||
|
|
endchoice # EXAMPLE_SDMMC_BUS_WIDTH
|
||
|
|
|
||
|
|
if SOC_SDMMC_USE_GPIO_MATRIX
|
||
|
|
|
||
|
|
config EXAMPLE_PIN_CMD
|
||
|
|
int "CMD GPIO number"
|
||
|
|
default 35 if IDF_TARGET_ESP32S3
|
||
|
|
|
||
|
|
config EXAMPLE_PIN_CLK
|
||
|
|
int "CLK GPIO number"
|
||
|
|
default 36 if IDF_TARGET_ESP32S3
|
||
|
|
|
||
|
|
config EXAMPLE_PIN_D0
|
||
|
|
int "D0 GPIO number"
|
||
|
|
default 37 if IDF_TARGET_ESP32S3
|
||
|
|
|
||
|
|
if EXAMPLE_SDMMC_BUS_WIDTH_4
|
||
|
|
|
||
|
|
config EXAMPLE_PIN_D1
|
||
|
|
int "D1 GPIO number"
|
||
|
|
default 38 if IDF_TARGET_ESP32S3
|
||
|
|
|
||
|
|
config EXAMPLE_PIN_D2
|
||
|
|
int "D2 GPIO number"
|
||
|
|
default 33 if IDF_TARGET_ESP32S3
|
||
|
|
|
||
|
|
config EXAMPLE_PIN_D3
|
||
|
|
int "D3 GPIO number"
|
||
|
|
default 34 if IDF_TARGET_ESP32S3
|
||
|
|
|
||
|
|
endif # EXAMPLE_SDMMC_BUS_WIDTH_4
|
||
|
|
|
||
|
|
endif # SOC_SDMMC_USE_GPIO_MATRIX
|
||
|
|
|
||
|
|
endif # EXAMPLE_USE_SDMMC
|
||
|
|
|
||
|
|
if EXAMPLE_USE_SDSPI
|
||
|
|
|
||
|
|
config EXAMPLE_PIN_MOSI
|
||
|
|
int "MOSI GPIO number"
|
||
|
|
default 15 if IDF_TARGET_ESP32
|
||
|
|
default 35 if IDF_TARGET_ESP32S2
|
||
|
|
default 35 if IDF_TARGET_ESP32S3
|
||
|
|
default 5 if IDF_TARGET_ESP32H2
|
||
|
|
default 4 # C3 and others
|
||
|
|
|
||
|
|
config EXAMPLE_PIN_MISO
|
||
|
|
int "MISO GPIO number"
|
||
|
|
default 2 if IDF_TARGET_ESP32
|
||
|
|
default 37 if IDF_TARGET_ESP32S2
|
||
|
|
default 37 if IDF_TARGET_ESP32S3
|
||
|
|
default 0 if IDF_TARGET_ESP32H2
|
||
|
|
default 6 # C3 and others
|
||
|
|
|
||
|
|
config EXAMPLE_PIN_CLK
|
||
|
|
int "CLK GPIO number"
|
||
|
|
default 14 if IDF_TARGET_ESP32
|
||
|
|
default 36 if IDF_TARGET_ESP32S2
|
||
|
|
default 36 if IDF_TARGET_ESP32S3
|
||
|
|
default 4 if IDF_TARGET_ESP32H2
|
||
|
|
default 5 # C3 and others
|
||
|
|
|
||
|
|
config EXAMPLE_PIN_CS
|
||
|
|
int "CS GPIO number"
|
||
|
|
default 13 if IDF_TARGET_ESP32
|
||
|
|
default 34 if IDF_TARGET_ESP32S2
|
||
|
|
default 34 if IDF_TARGET_ESP32S3
|
||
|
|
default 1 # C3 and others
|
||
|
|
|
||
|
|
endif # EXAMPLE_USE_SDSPI
|
||
|
|
|
||
|
|
endmenu # "SD card test config"
|
||
|
|
|
||
|
|
endmenu # "Performance Monitor Example Configuration"
|