esp-idf/examples/ethernet/enc28j60/main/enc28j60_example_main.c

145 lines
5.7 KiB
C
Raw Normal View History

2020-01-09 06:32:51 -05:00
/* ENC28J60 Example
This example code is in the Public Domain (or CC0 licensed, at your option.)
Unless required by applicable law or agreed to in writing, this
software is distributed on an "AS IS" BASIS, WITHOUT WARRANTIES OR
CONDITIONS OF ANY KIND, either express or implied.
*/
#include <stdio.h>
#include <string.h>
2020-11-06 03:06:20 -05:00
#include "sdkconfig.h"
2020-01-09 06:32:51 -05:00
#include "freertos/FreeRTOS.h"
#include "freertos/task.h"
#include "esp_netif.h"
#include "esp_eth.h"
#include "esp_event.h"
#include "esp_log.h"
#include "driver/gpio.h"
#include "esp_eth_enc28j60.h"
2020-11-06 03:06:20 -05:00
#include "driver/spi_master.h"
2020-01-09 06:32:51 -05:00
static const char *TAG = "eth_example";
/** Event handler for Ethernet events */
static void eth_event_handler(void *arg, esp_event_base_t event_base,
int32_t event_id, void *event_data)
{
uint8_t mac_addr[6] = {0};
/* we can get the ethernet driver handle from event data */
esp_eth_handle_t eth_handle = *(esp_eth_handle_t *)event_data;
switch (event_id) {
case ETHERNET_EVENT_CONNECTED:
esp_eth_ioctl(eth_handle, ETH_CMD_G_MAC_ADDR, mac_addr);
ESP_LOGI(TAG, "Ethernet Link Up");
ESP_LOGI(TAG, "Ethernet HW Addr %02x:%02x:%02x:%02x:%02x:%02x",
mac_addr[0], mac_addr[1], mac_addr[2], mac_addr[3], mac_addr[4], mac_addr[5]);
break;
case ETHERNET_EVENT_DISCONNECTED:
ESP_LOGI(TAG, "Ethernet Link Down");
break;
case ETHERNET_EVENT_START:
ESP_LOGI(TAG, "Ethernet Started");
break;
case ETHERNET_EVENT_STOP:
ESP_LOGI(TAG, "Ethernet Stopped");
break;
default:
break;
}
}
/** Event handler for IP_EVENT_ETH_GOT_IP */
static void got_ip_event_handler(void *arg, esp_event_base_t event_base,
int32_t event_id, void *event_data)
{
ip_event_got_ip_t *event = (ip_event_got_ip_t *) event_data;
const esp_netif_ip_info_t *ip_info = &event->ip_info;
ESP_LOGI(TAG, "Ethernet Got IP Address");
ESP_LOGI(TAG, "~~~~~~~~~~~");
ESP_LOGI(TAG, "ETHIP:" IPSTR, IP2STR(&ip_info->ip));
ESP_LOGI(TAG, "ETHMASK:" IPSTR, IP2STR(&ip_info->netmask));
ESP_LOGI(TAG, "ETHGW:" IPSTR, IP2STR(&ip_info->gw));
ESP_LOGI(TAG, "~~~~~~~~~~~");
}
void app_main(void)
{
ESP_ERROR_CHECK(gpio_install_isr_service(0));
// Initialize TCP/IP network interface (should be called only once in application)
ESP_ERROR_CHECK(esp_netif_init());
// Create default event loop that running in background
ESP_ERROR_CHECK(esp_event_loop_create_default());
esp_netif_config_t netif_cfg = ESP_NETIF_DEFAULT_ETH();
esp_netif_t *eth_netif = esp_netif_new(&netif_cfg);
spi_bus_config_t buscfg = {
.miso_io_num = CONFIG_EXAMPLE_ENC28J60_MISO_GPIO,
.mosi_io_num = CONFIG_EXAMPLE_ENC28J60_MOSI_GPIO,
.sclk_io_num = CONFIG_EXAMPLE_ENC28J60_SCLK_GPIO,
.quadwp_io_num = -1,
.quadhd_io_num = -1,
};
ESP_ERROR_CHECK(spi_bus_initialize(CONFIG_EXAMPLE_ENC28J60_SPI_HOST, &buscfg, SPI_DMA_CH_AUTO));
2020-01-09 06:32:51 -05:00
/* ENC28J60 ethernet driver is based on spi driver */
spi_device_interface_config_t devcfg = {
.command_bits = 3,
.address_bits = 5,
.mode = 0,
.clock_speed_hz = CONFIG_EXAMPLE_ENC28J60_SPI_CLOCK_MHZ * 1000 * 1000,
2020-01-09 06:32:51 -05:00
.spics_io_num = CONFIG_EXAMPLE_ENC28J60_CS_GPIO,
.queue_size = 20,
.cs_ena_posttrans = enc28j60_cal_spi_cs_hold_time(CONFIG_EXAMPLE_ENC28J60_SPI_CLOCK_MHZ),
2020-01-09 06:32:51 -05:00
};
2020-01-09 06:32:51 -05:00
spi_device_handle_t spi_handle = NULL;
ESP_ERROR_CHECK(spi_bus_add_device(CONFIG_EXAMPLE_ENC28J60_SPI_HOST, &devcfg, &spi_handle));
eth_enc28j60_config_t enc28j60_config = ETH_ENC28J60_DEFAULT_CONFIG(spi_handle);
enc28j60_config.int_gpio_num = CONFIG_EXAMPLE_ENC28J60_INT_GPIO;
eth_mac_config_t mac_config = ETH_MAC_DEFAULT_CONFIG();
mac_config.smi_mdc_gpio_num = -1; // ENC28J60 doesn't have SMI interface
mac_config.smi_mdio_gpio_num = -1;
esp_eth_mac_t *mac = esp_eth_mac_new_enc28j60(&enc28j60_config, &mac_config);
eth_phy_config_t phy_config = ETH_PHY_DEFAULT_CONFIG();
phy_config.autonego_timeout_ms = 0; // ENC28J60 doesn't support auto-negotiation
phy_config.reset_gpio_num = -1; // ENC28J60 doesn't have a pin to reset internal PHY
esp_eth_phy_t *phy = esp_eth_phy_new_enc28j60(&phy_config);
esp_eth_config_t eth_config = ETH_DEFAULT_CONFIG(mac, phy);
esp_eth_handle_t eth_handle = NULL;
ESP_ERROR_CHECK(esp_eth_driver_install(&eth_config, &eth_handle));
/* ENC28J60 doesn't burn any factory MAC address, we need to set it manually.
02:00:00 is a Locally Administered OUI range so should not be used except when testing on a LAN under your control.
*/
mac->set_addr(mac, (uint8_t[]) {
0x02, 0x00, 0x00, 0x12, 0x34, 0x56
});
// ENC28J60 Errata #1 check
if (emac_enc28j60_get_chip_info(mac) < ENC28J60_REV_B5 && CONFIG_EXAMPLE_ENC28J60_SPI_CLOCK_MHZ < 8) {
ESP_LOGE(TAG, "SPI frequency must be at least 8 MHz for chip revision less than 5");
ESP_ERROR_CHECK(ESP_FAIL);
}
2020-01-09 06:32:51 -05:00
/* attach Ethernet driver to TCP/IP stack */
ESP_ERROR_CHECK(esp_netif_attach(eth_netif, esp_eth_new_netif_glue(eth_handle)));
// Register user defined event handers
ESP_ERROR_CHECK(esp_event_handler_register(ETH_EVENT, ESP_EVENT_ANY_ID, &eth_event_handler, NULL));
ESP_ERROR_CHECK(esp_event_handler_register(IP_EVENT, IP_EVENT_ETH_GOT_IP, &got_ip_event_handler, NULL));
/* It is recommended to use ENC28J60 in Full Duplex mode since multiple errata exist to the Half Duplex mode */
#if CONFIG_EXAMPLE_ENC28J60_DUPLEX_FULL
eth_duplex_t duplex = ETH_DUPLEX_FULL;
ESP_ERROR_CHECK(esp_eth_ioctl(eth_handle, ETH_CMD_S_DUPLEX_MODE, &duplex));
#endif
/* start Ethernet driver state machine */
ESP_ERROR_CHECK(esp_eth_start(eth_handle));
2020-01-09 06:32:51 -05:00
}