mirror of
https://github.com/espressif/esp-idf.git
synced 2024-10-05 20:47:46 -04:00
52 lines
1.6 KiB
C
52 lines
1.6 KiB
C
|
/* ADC1 Example
|
||
|
|
|
||
|
|
This example code is in the Public Domain (or CC0 licensed, at your option.)
|
||
|
|
|
||
|
|
Unless required by applicable law or agreed to in writing, this
|
||
|
|
software is distributed on an "AS IS" BASIS, WITHOUT WARRANTIES OR
|
||
|
|
CONDITIONS OF ANY KIND, either express or implied.
|
||
|
|
*/
|
||
|
|
#include <stdio.h>
|
||
|
|
#include <stdlib.h>
|
||
|
|
#include "freertos/FreeRTOS.h"
|
||
|
|
#include "freertos/task.h"
|
||
|
|
#include "freertos/queue.h"
|
||
|
|
#include "driver/gpio.h"
|
||
|
|
#include "driver/adc.h"
|
||
|
|
#include "esp_system.h"
|
||
|
|
#include "esp_adc_cal.h"
|
||
|
|
|
||
|
|
/*Note: Different ESP32 modules may have different reference voltages varying from
|
||
|
|
* 1000mV to 1200mV. Use #define GET_VREF to route v_ref to a GPIO
|
||
|
|
*/
|
||
|
|
#define V_REF 1100
|
||
|
|
#define ADC1_TEST_CHANNEL (ADC1_CHANNEL_6) //GPIO 34
|
||
|
|
//#define V_REF_TO_GPIO //Remove comment on define to route v_ref to GPIO
|
||
|
|
|
||
|
|
void app_main(void)
|
||
|
|
{
|
||
|
|
#ifndef V_REF_TO_GPIO
|
||
|
|
//Init ADC and Characteristics
|
||
|
|
esp_adc_cal_characteristics_t characteristics;
|
||
|
|
adc1_config_width(ADC_WIDTH_12Bit);
|
||
|
|
adc1_config_channel_atten(ADC1_TEST_CHANNEL, ADC_ATTEN_0db);
|
||
|
|
esp_adc_cal_get_characteristics(V_REF, ADC_ATTEN_0db, ADC_WIDTH_12Bit, &characteristics);
|
||
|
|
uint32_t voltage;
|
||
|
|
while(1){
|
||
|
|
voltage = adc1_to_voltage(ADC1_TEST_CHANNEL, &characteristics);
|
||
|
|
printf("%d mV\n",voltage);
|
||
|
|
vTaskDelay(pdMS_TO_TICKS(1000));
|
||
|
|
}
|
||
|
|
#else
|
||
|
|
//Get v_ref
|
||
|
|
esp_err_t status;
|
||
|
|
status = adc2_vref_to_gpio(GPIO_NUM_25);
|
||
|
|
if (status == ESP_OK){
|
||
|
|
printf("v_ref routed to GPIO\n");
|
||
|
|
}else{
|
||
|
|
printf("failed to route v_ref\n");
|
||
|
|
}
|
||
|
|
fflush(stdout);
|
||
|
|
#endif
|
||
|
|
}
|