This user guide will help you get started with ESP32-S2-DevKitC-1 and will also provide more in-depth information.
ESP32-S2-DevKitC-1 is an entry-level development board based on ESP32-S2-SOLO (on-board PCB antenna) or ESP32-S2-SOLO-U (external antenna connector), which are two general-purpose modules with a 4 MB SPI flash. This board integrates complete Wi-Fi functions.
Most of the I/O pins are broken out to the pin headers on both sides for easy interfacing. Developers can either connect peripherals with jumper wires or mount ESP32-S2-DevKitC-1 on a breadboard.
:alt:ESP32-S2-DevKitC-1 with the ESP32-S2-SOLO Module
:figclass:align-center
ESP32-S2-DevKitC-1 with the ESP32-S2-SOLO Module
The document consists of the following major sections:
-`Getting Started`_: Overview of ESP32-S2-DevKitC-1 and hardware/software setup instructions to get started.
-`Hardware Reference`_: More detailed information about the ESP32-S2-DevKitC-1's hardware.
-`Hardware Revision Details`_: Revision history, known issues, and links to user guides for previous versions (if any) of ESP32-S2-DevKitC-1.
-`Related Documents`_: Links to related documentation.
Getting Started
===============
This section provides a brief introduction of ESP32-S2-DevKitC-1, instructions on how to do the initial hardware setup and how to flash firmware onto it.
- ESP32-S2-SOLO and ESP32-S2-SOLO-U are two general-purpose Wi-Fi modules. ESP32-S2-SOLO comes with an on-board PCB antenna and ESP32-S2-SOLO-U comes with a connector for an external antenna. ESP32-S2-SOLO or ESP32-S2-SOLO-U on the board may come either with a 4 MB flash, or a 4 MB flash plus a 2 MB PSRAM embedded in the chip.
- All available GPIO pins (except for the SPI bus for flash) are broken out to the pin headers on the board. For details, please see :ref:`user-guide-s2-devkitc-1-v1-header-blocks`.
* - ESP32-S2 USB Port
- ESP32-S2 full-speed USB OTG interface, compliant with the USB 1.1 specifications. The interface is used for power supply to the board, for flashing applications to the chip, and for communication with the chip using USB 1.1 protocols.
* - Reset Button
- Press this button to restart the system.
* - Boot Button
- Download button. Holding down **Boot** and then pressing **Reset** initiates Firmware Download mode for downloading firmware through the serial port.
- A Micro-USB port used for power supply to the board, for flashing applications to the chip, as well as the communication with the chip via the on-board USB-to-UART bridge.
- Power regulator that converts a 5 V supply into a 3.3 V output.
Start Application Development
-----------------------------
Before powering up your ESP32-S2-DevKitC-1, please make sure that it is in good condition with no obvious signs of damage.
Required Hardware
^^^^^^^^^^^^^^^^^
- ESP32-S2-DevKitC-1
- USB 2.0 cable (Standard-A to Micro-B)
- Computer running Windows, Linux, or macOS
..note::
Be sure to use an appropriate USB cable. Some cables are for charging only and do not provide the needed data lines nor work for programming the boards.
Hardware Setup
^^^^^^^^^^^^^^
Connect the board with the computer using **USB-to-UART Port**. Connection using **ESP32-S2 USB Port** is not fully documented. In subsequent steps, **USB-to-UART Port** will be used by default.
Software Setup
^^^^^^^^^^^^^^
Please proceed to `ESP-IDF Get Started <https://docs.espressif.com/projects/esp-idf/en/latest/esp32s2/get-started/index.html>`_, where Section `Installation Step by Step <https://docs.espressif.com/projects/esp-idf/zh_CN/latest/esp32s2/get-started/index.html#get-started-step-by-step>`_ will quickly help you set up the development environment and then flash an application example into your ESP32-S2-DevKitC-1.
Contents and Packaging
----------------------
Retail orders
^^^^^^^^^^^^^
If you order a few samples, each ESP32-S2-DevKitC-1 comes in an individual package in either antistatic bag or any packaging depending on your retailer.
The two tables below provide the **Name** and **Function** of the pin headers on both sides of the board (J1 and J3). The pin header names are shown in :ref:`user-guide-s2-devkitc-1-v1-board-front`. The numbering is the same as in the `ESP32-S2-DevKitC-1 Schematic <https://dl.espressif.com/dl/schematics/SCH_ESP32-S2-DEVKITC-1_V1_20210508.pdf>`_ (PDF).
*`ESP32-S2-DevKitC-1 Dimensions source file <https://dl.espressif.com/dl/schematics/DXF_ESP32-S2-DevKitC-1_V1_20210511.dxf>`_ (DXF) - You can view it with `Autodesk Viewer <https://viewer.autodesk.com/>`_ online
For further design documentation for the board, please contact us at `sales@espressif.com <sales@espressif.com>`_.
