This user guide will help you get started with ESP32-C3-DevKitC-02 and will also provide more in-depth information.
ESP32-C3-DevKitC-02 is an entry-level development board based on `ESP32-C3-WROOM-02 <https://www.espressif.com/sites/default/files/documentation/esp32-c3-wroom-02_datasheet_en.pdf>`_, a general-purpose module with 4 MB SPI flash. This board integrates complete Wi-Fi and Bluetooth LE functions.
Most of the I/O pins are broken out to the pin headers on both sides for easy interfacing. Developers can either connect peripherals with jumper wires or mount ESP32-C3-DevKitC-02 on a breadboard.
The document consists of the following major sections:
-`Getting Started`_: Overview of ESP32-C3-DevKitM-1 and hardware/software setup instructions to get started.
-`Hardware Reference`_: More detailed information about the ESP32-C3-DevKitM-1's hardware.
-`Hardware Revision Details`_: Revision history, known issues, and links to user guides for previous versions (if any) of ESP32-C3-DevKitM-1.
-`Related Documents`_: Links to related documentation.
Getting Started
===============
This section provides a brief introduction of ESP32-C3-DevKitM-1, instructions on how to do the initial hardware setup and how to flash firmware onto it.
- ESP32-C3-WROOM-02 from Espressif is a powerful and general-purpose module that offers Wi-Fi and Bluetooth LE coexistence. It has a PCB antenna and a 4 MB SPI flash.
* - 5 V to 3.3 V LDO
- Power regulator that converts a 5 V supply into a 3.3 V output.
* - 5 V Power On LED
- Turns on when the USB power is connected to the board.
* - I/O Connector
- All available GPIO pins (except for the SPI bus for flash) are broken out to the pin headers on the board. For details, please see :ref:`user-guide-c3-devkitc-02-v1-header-blocks`.
* - Boot Button
- Download button. Holding down **Boot** and then pressing **Reset** initiates Firmware Download mode for downloading firmware through the serial port.
* - Micro-USB Port
- USB interface. Power supply for the board as well as the communication interface between a computer and the ESP32-C3 chip.
* - Reset Button
- Press this button to restart the system.
* - USB-to-UART Bridge
- Single USB-to-UART bridge chip provides transfer rates up to 3 Mbps.
* - RGB LED
- Addressable RGB LED, driven by GPIO8.
Start Application Development
-----------------------------
Before powering up your ESP32-C3-DevKitC-02, please make sure that it is in good condition with no obvious signs of damage.
Required Hardware
^^^^^^^^^^^^^^^^^
- ESP32-C3-DevKitC-02
- USB 2.0 cable (Standard-A to Micro-B)
- Computer running Windows, Linux, or macOS
..note::
Be sure to use a good quality USB cable. Some cables are for charging only and do not provide the needed data lines nor work for programming the boards.
Software Setup
^^^^^^^^^^^^^^
Please proceed to :doc:`../../get-started/index`, where Section :ref:`get-started-step-by-step` will quickly help you set up the development environment and then flash an application example into your ESP32-C3-DevKitC-02.
Contents and Packaging
----------------------
Retail orders
^^^^^^^^^^^^^
If you order a few samples, each ESP32-C3-DevKitC-02 comes in an individual package in either antistatic bag or any packaging depending on your retailer.
For retail orders, please go to https://www.espressif.com/en/company/contact/buy-a-sample.
Wholesale Orders
^^^^^^^^^^^^^^^^
If you order in bulk, the boards come in large cardboard boxes.
For wholesale orders, please check `Espressif Product Ordering Information <https://www.espressif.com/sites/default/files/documentation/espressif_products_ordering_information_en.pdf>`_ (PDF)
Hardware Reference
==================
Block Diagram
-------------
The block diagram below shows the components of ESP32-C3-DevKitC-02 and their interconnections.
There are three mutually exclusive ways to provide power to the board:
- Micro USB port, default power supply
- 5V and GND header pins
- 3V3 and GND header pins
It is recommended to use the first option: micro USB port.
.._user-guide-c3-devkitc-02-v1-header-blocks:
Header Block
------------
The two tables below provide the **Name** and **Function** of I/O header pins on both sides of the board, as shown in :ref:`user-guide-c3-devkitc-02-v1-board-front`. The numbering and names are the same as in the `ESP32-C3-DevKitC-02 Schematic <https://dl.espressif.com/dl/schematics/SCH_ESP32-C3-DEVKITC-02_V1_1_20210126A.pdf>`_ (PDF).
*`ESP32-C3-DevKitC-02 Dimensions source file <https://dl.espressif.com/dl/schematics/DXF_ESP32-C3-DevKitC-02_V1_1_20210121AA.dxf>`_ (DXF) - You can view it with `Autodesk Viewer <https://viewer.autodesk.com/>`_ online
For further design documentation for the board, please contact us at `sales@espressif.com <sales@espressif.com>`_.
