esp-idf/components/soc/esp32/include/hal/spi_flash_ll.h

358 lines
11 KiB
C
Raw Normal View History

// Copyright 2015-2019 Espressif Systems (Shanghai) PTE LTD
//
// Licensed under the Apache License, Version 2.0 (the "License");
// you may not use this file except in compliance with the License.
// You may obtain a copy of the License at
//
// http://www.apache.org/licenses/LICENSE-2.0
//
// Unless required by applicable law or agreed to in writing, software
// distributed under the License is distributed on an "AS IS" BASIS,
// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
// See the License for the specific language governing permissions and
// limitations under the License.
/*******************************************************************************
* NOTICE
* The ll is not public api, don't use in application code.
* See readme.md in soc/include/hal/readme.md
******************************************************************************/
// The Lowlevel layer for SPI Flash
#pragma once
#include <stdlib.h>
#include "soc/spi_periph.h"
#include "hal/spi_types.h"
#include "hal/spi_flash_types.h"
#include <sys/param.h> // For MIN/MAX
#include <stdbool.h>
#include <string.h>
//Supported clock register values
#define SPI_FLASH_LL_CLKREG_VAL_5MHZ ((spi_flash_ll_clock_reg_t){.val=0x0000F1CF}) ///< Clock set to 5 MHz
#define SPI_FLASH_LL_CLKREG_VAL_10MHZ ((spi_flash_ll_clock_reg_t){.val=0x000070C7}) ///< Clock set to 10 MHz
#define SPI_FLASH_LL_CLKREG_VAL_20MHZ ((spi_flash_ll_clock_reg_t){.val=0x00003043}) ///< Clock set to 20 MHz
#define SPI_FLASH_LL_CLKREG_VAL_26MHZ ((spi_flash_ll_clock_reg_t){.val=0x00002002}) ///< Clock set to 26 MHz
#define SPI_FLASH_LL_CLKREG_VAL_40MHZ ((spi_flash_ll_clock_reg_t){.val=0x00001001}) ///< Clock set to 40 MHz
#define SPI_FLASH_LL_CLKREG_VAL_80MHZ ((spi_flash_ll_clock_reg_t){.val=0x80000000}) ///< Clock set to 80 MHz
/// Get the start address of SPI peripheral registers by the host ID
#define spi_flash_ll_get_hw(host_id) ((host_id)==SPI1_HOST? &SPI1:((host_id)==SPI2_HOST?&SPI2:((host_id)==SPI3_HOST?&SPI3:({abort();(spi_dev_t*)0;}))))
/// type to store pre-calculated register value in above layers
typedef typeof(SPI1.clock) spi_flash_ll_clock_reg_t;
/*------------------------------------------------------------------------------
* Control
*----------------------------------------------------------------------------*/
/**
* Reset peripheral registers before configuration and starting control
*
* @param dev Beginning address of the peripheral registers.
*/
static inline void spi_flash_ll_reset(spi_dev_t *dev)
{
dev->user.val = 0;
dev->ctrl.val = 0;
}
/**
* Check whether the previous operation is done.
*
* @param dev Beginning address of the peripheral registers.
*
* @return true if last command is done, otherwise false.
*/
static inline bool spi_flash_ll_cmd_is_done(const spi_dev_t *dev)
{
return (dev->cmd.val == 0);
}
/**
* Erase the flash chip.
*
* @param dev Beginning address of the peripheral registers.
*/
static inline void spi_flash_ll_erase_chip(spi_dev_t *dev)
{
dev->cmd.flash_ce = 1;
}
/**
* Erase the sector, the address should be set by spi_flash_ll_set_address.
*
* @param dev Beginning address of the peripheral registers.
*/
static inline void spi_flash_ll_erase_sector(spi_dev_t *dev)
{
dev->ctrl.val = 0;
dev->cmd.flash_se = 1;
}
/**
* Erase the block, the address should be set by spi_flash_ll_set_address.
*
* @param dev Beginning address of the peripheral registers.
*/
static inline void spi_flash_ll_erase_block(spi_dev_t *dev)
{
dev->cmd.flash_be = 1;
}
/**
* Enable/disable write protection for the flash chip.
*
* @param dev Beginning address of the peripheral registers.
* @param wp true to enable the protection, false to disable (write enable).
*/
static inline void spi_flash_ll_set_write_protect(spi_dev_t *dev, bool wp)
{
if (wp) {
dev->cmd.flash_wrdi = 1;
} else {
dev->cmd.flash_wren = 1;
}
}
/**
* Get the read data from the buffer after ``spi_flash_ll_read`` is done.
*
* @param dev Beginning address of the peripheral registers.
* @param buffer Buffer to hold the output data
* @param read_len Length to get out of the buffer
*/
static inline void spi_flash_ll_get_buffer_data(spi_dev_t *dev, void *buffer, uint32_t read_len)
{
if (((intptr_t)buffer % 4 == 0) && (read_len % 4 == 0)) {
// If everything is word-aligned, do a faster memcpy
memcpy(buffer, (void *)dev->data_buf, read_len);
} else {
// Otherwise, slow(er) path copies word by word
int copy_len = read_len;
for (int i = 0; i < (read_len + 3) / 4; i++) {
int word_len = MIN(sizeof(uint32_t), copy_len);
uint32_t word = dev->data_buf[i];
memcpy(buffer, &word, word_len);
buffer = (void *)((intptr_t)buffer + word_len);
copy_len -= word_len;
}
}
}
/**
* Write a word to the data buffer.
*
* @param dev Beginning address of the peripheral registers.
* @param word Data to write at address 0.
*/
static inline void spi_flash_ll_write_word(spi_dev_t *dev, uint32_t word)
{
dev->data_buf[0] = word;
}
/**
* Program a page of the flash chip. Call ``spi_flash_ll_set_address`` before
* this to set the address to program.
*
* @param dev Beginning address of the peripheral registers.
* @param buffer Buffer holding the data to program
* @param length Length to program.
*/
static inline void spi_flash_ll_program_page(spi_dev_t *dev, const void *buffer, uint32_t length)
{
dev->user.usr_dummy = 0;
// Load data registers, word at a time
int num_words = (length + 3) / 4;
for (int i = 0; i < num_words; i++) {
uint32_t word = 0;
uint32_t word_len = MIN(length, sizeof(word));
memcpy(&word, buffer, word_len);
dev->data_buf[i] = word;
length -= word_len;
buffer = (void *)((intptr_t)buffer + word_len);
}
dev->cmd.flash_pp = 1;
}
/**
* Trigger a user defined transaction. All phases, including command, address, dummy, and the data phases,
* should be configured before this is called.
*
* @param dev Beginning address of the peripheral registers.
*/
static inline void spi_flash_ll_user_start(spi_dev_t *dev)
{
dev->cmd.usr = 1;
}
/**
* Check whether the host is idle to perform new commands.
*
* @param dev Beginning address of the peripheral registers.
*
* @return true if the host is idle, otherwise false
*/
static inline bool spi_flash_ll_host_idle(const spi_dev_t *dev)
{
return dev->ext2.st != 0;
}
/**
* Set phases for user-defined transaction to read
*
* @param dev Beginning address of the peripheral registers.
*/
static inline void spi_flash_ll_read_phase(spi_dev_t *dev)
{
typeof (dev->user) user = {
.usr_command = 1,
.usr_mosi = 0,
.usr_miso = 1,
.usr_addr = 1,
};
dev->user = user;
}
/*------------------------------------------------------------------------------
* Configs
*----------------------------------------------------------------------------*/
/**
* Select which pin to use for the flash
*
* @param dev Beginning address of the peripheral registers.
* @param pin Pin ID to use, 0-2. Set to other values to disable all the CS pins.
*/
static inline void spi_flash_ll_set_cs_pin(spi_dev_t *dev, int pin)
{
dev->pin.cs0_dis = (pin == 0) ? 0 : 1;
dev->pin.cs1_dis = (pin == 1) ? 0 : 1;
dev->pin.cs2_dis = (pin == 2) ? 0 : 1;
}
/**
* Set the read io mode.
*
* @param dev Beginning address of the peripheral registers.
* @param read_mode I/O mode to use in the following transactions.
*/
static inline void spi_flash_ll_set_read_mode(spi_dev_t *dev, esp_flash_read_mode_t read_mode)
{
typeof (dev->ctrl) ctrl = dev->ctrl;
ctrl.val &= ~(SPI_FREAD_QIO_M | SPI_FREAD_QUAD_M | SPI_FREAD_DIO_M | SPI_FREAD_DUAL_M);
ctrl.val |= SPI_FASTRD_MODE_M;
switch (read_mode) {
case SPI_FLASH_FASTRD:
//the default option
break;
case SPI_FLASH_QIO:
ctrl.fread_qio = 1;
break;
case SPI_FLASH_QOUT:
ctrl.fread_quad = 1;
break;
case SPI_FLASH_DIO:
ctrl.fread_dio = 1;
break;
case SPI_FLASH_DOUT:
ctrl.fread_dual = 1;
break;
case SPI_FLASH_SLOWRD:
ctrl.fastrd_mode = 0;
break;
default:
abort();
}
dev->ctrl = ctrl;
}
/**
* Set clock frequency to work at.
*
* @param dev Beginning address of the peripheral registers.
* @param clock_val pointer to the clock value to set
*/
static inline void spi_flash_ll_set_clock(spi_dev_t *dev, spi_flash_ll_clock_reg_t *clock_val)
{
dev->clock = *clock_val;
}
/**
* Set the input length, in bits.
*
* @param dev Beginning address of the peripheral registers.
* @param bitlen Length of input, in bits.
*/
static inline void spi_flash_ll_set_miso_bitlen(spi_dev_t *dev, uint32_t bitlen)
{
dev->user.usr_miso = bitlen > 0;
dev->miso_dlen.usr_miso_dbitlen = bitlen ? (bitlen - 1) : 0;
}
/**
* Set the output length, in bits (not including command, address and dummy
* phases)
*
* @param dev Beginning address of the peripheral registers.
* @param bitlen Length of output, in bits.
*/
static inline void spi_flash_ll_set_mosi_bitlen(spi_dev_t *dev, uint32_t bitlen)
{
dev->user.usr_mosi = bitlen > 0;
dev->mosi_dlen.usr_mosi_dbitlen = bitlen ? (bitlen - 1) : 0;
}
/**
* Set the command with fixed length (8 bits).
*
* @param dev Beginning address of the peripheral registers.
* @param command Command to send
*/
static inline void spi_flash_ll_set_command8(spi_dev_t *dev, uint8_t command)
{
dev->user.usr_command = 1;
typeof(dev->user2) user2 = {
.usr_command_value = command,
.usr_command_bitlen = (8 - 1),
};
dev->user2 = user2;
}
/**
* Set the address length to send, in bits. Should be called before commands that requires the address e.g. erase sector, read, write...
*
* @param dev Beginning address of the peripheral registers.
* @param bitlen Length of the address, in bits
*/
static inline void spi_flash_ll_set_addr_bitlen(spi_dev_t *dev, uint32_t bitlen)
{
dev->user1.usr_addr_bitlen = (bitlen - 1);
dev->user.usr_addr = bitlen ? 1 : 0;
}
/**
* Set the address to send. Should be called before commands that requires the address e.g. erase sector, read, write...
*
* @param dev Beginning address of the peripheral registers.
* @param addr Address to send
*/
static inline void spi_flash_ll_set_address(spi_dev_t *dev, uint32_t addr)
{
dev->addr = addr;
}
/**
* Set the length of dummy cycles.
*
* @param dev Beginning address of the peripheral registers.
* @param dummy_n Cycles of dummy phases
*/
static inline void spi_flash_ll_set_dummy(spi_dev_t *dev, uint32_t dummy_n)
{
dev->user.usr_dummy = dummy_n ? 1 : 0;
dev->user1.usr_dummy_cyclelen = dummy_n - 1;
}