2020-02-02 10:23:16 -05:00
|
|
|
menu "ESP System Settings"
|
|
|
|
|
|
|
|
|
|
choice ESP_SYSTEM_PANIC
|
|
|
|
|
prompt "Panic handler behaviour"
|
|
|
|
|
default ESP_SYSTEM_PANIC_PRINT_REBOOT
|
|
|
|
|
help
|
|
|
|
|
If FreeRTOS detects unexpected behaviour or an unhandled exception, the panic handler is
|
|
|
|
|
invoked. Configure the panic handler's action here.
|
|
|
|
|
|
|
|
|
|
config ESP_SYSTEM_PANIC_PRINT_HALT
|
|
|
|
|
bool "Print registers and halt"
|
|
|
|
|
help
|
|
|
|
|
Outputs the relevant registers over the serial port and halt the
|
|
|
|
|
processor. Needs a manual reset to restart.
|
|
|
|
|
|
|
|
|
|
config ESP_SYSTEM_PANIC_PRINT_REBOOT
|
|
|
|
|
bool "Print registers and reboot"
|
|
|
|
|
help
|
|
|
|
|
Outputs the relevant registers over the serial port and immediately
|
|
|
|
|
reset the processor.
|
|
|
|
|
|
|
|
|
|
config ESP_SYSTEM_PANIC_SILENT_REBOOT
|
|
|
|
|
bool "Silent reboot"
|
|
|
|
|
help
|
|
|
|
|
Just resets the processor without outputting anything
|
|
|
|
|
|
|
|
|
|
config ESP_SYSTEM_PANIC_GDBSTUB
|
|
|
|
|
bool "Invoke GDBStub"
|
|
|
|
|
select ESP_GDBSTUB_ENABLED
|
|
|
|
|
help
|
|
|
|
|
Invoke gdbstub on the serial port, allowing for gdb to attach to it to do a postmortem
|
|
|
|
|
of the crash.
|
|
|
|
|
endchoice
|
|
|
|
|
|
2020-02-13 07:43:23 -05:00
|
|
|
config ESP_SYSTEM_SINGLE_CORE_MODE
|
|
|
|
|
bool
|
|
|
|
|
default n
|
|
|
|
|
help
|
|
|
|
|
Only initialize and use the main core.
|
|
|
|
|
|
2020-07-14 08:39:30 -04:00
|
|
|
config ESP_SYSTEM_RTC_EXT_XTAL
|
|
|
|
|
# This is a High Layer Kconfig option, invisible, can be selected by other Kconfig option
|
|
|
|
|
# e.g. It will be selected on when ESP32_RTC_CLK_SRC_EXT_CRYS is on
|
|
|
|
|
bool
|
|
|
|
|
default n
|
|
|
|
|
|
|
|
|
|
config ESP_SYSTEM_RTC_EXT_XTAL_BOOTSTRAP_CYCLES
|
|
|
|
|
int "Bootstrap cycles for external 32kHz crystal"
|
|
|
|
|
depends on ESP_SYSTEM_RTC_EXT_XTAL
|
|
|
|
|
default 5 if IDF_TARGET_ESP32
|
|
|
|
|
default 0
|
|
|
|
|
range 0 32768
|
|
|
|
|
help
|
|
|
|
|
To reduce the startup time of an external RTC crystal,
|
|
|
|
|
we bootstrap it with a 32kHz square wave for a fixed number of cycles.
|
|
|
|
|
Setting 0 will disable bootstrapping (if disabled, the crystal may take
|
|
|
|
|
longer to start up or fail to oscillate under some conditions).
|
|
|
|
|
|
|
|
|
|
If this value is too high, a faulty crystal may initially start and then fail.
|
|
|
|
|
If this value is too low, an otherwise good crystal may not start.
|
|
|
|
|
|
|
|
|
|
To accurately determine if the crystal has started,
|
|
|
|
|
set a larger "Number of cycles for RTC_SLOW_CLK calibration" (about 3000).
|
|
|
|
|
|
2020-02-02 10:23:16 -05:00
|
|
|
endmenu # ESP System Settings
|
