mirror of
https://github.com/espressif/esp-idf.git
synced 2024-09-26 15:13:28 -04:00
62 lines
2.7 KiB
Markdown
62 lines
2.7 KiB
Markdown
|
| Supported Targets | ESP32 | ESP32-C3 | ESP32-C6 | ESP32-S2 | ESP32-S3 |
|
||
|
|
| ----------------- | ----- | -------- | -------- | -------- | -------- |
|
||
|
|
|
||
|
|
# Sigma Delta Modulation DAC Example
|
||
|
|
|
||
|
|
(See the README.md file in the upper level 'examples' directory for more information about examples.)
|
||
|
|
|
||
|
|
This example uses the sigma-delta driver to generate modulated output on a GPIO. If you filter the output signal with an active or passive filter, you can get a 1 KHz sine wave.
|
||
|
|
|
||
|
|
## How to use example
|
||
|
|
|
||
|
|
### Hardware Required
|
||
|
|
|
||
|
|
* A development board with any supported Espressif SoC (e.g., ESP32-DevKitC, ESP-WROVER-KIT, etc.)
|
||
|
|
* A USB cable for Power supply and programming
|
||
|
|
* An active or passive filter. Connect them as below:
|
||
|
|
|
||
|
|
```
|
||
|
|
┌──────────────────────────────┐
|
||
|
|
│ ESP │ ┌───────────────────┐
|
||
|
|
│ │ │ Active or Passive │ Sine Wave
|
||
|
|
│ EXAMPLE_SIGMA_DELTA_GPIO_NUM ├────►│ Filter ├──────────────
|
||
|
|
└──────────────────────────────┘ └───────────────────┘
|
||
|
|
```
|
||
|
|
|
||
|
|
### Configure the project
|
||
|
|
|
||
|
|
The main configurations can be update by the macro that defined at the top of the [example source file](main/sdm_dac_example_main.c), including the output gpio, timer callback interval and the sine wave frequency and amplitude.
|
||
|
|
|
||
|
|
### Build and Flash
|
||
|
|
|
||
|
|
Build the project and flash it to the board, then run the monitor tool to view the serial output:
|
||
|
|
|
||
|
|
Run `idf.py -p PORT flash monitor` to build, flash and monitor the project.
|
||
|
|
|
||
|
|
(To exit the serial monitor, type ``Ctrl-]``.)
|
||
|
|
|
||
|
|
See the [Getting Started Guide](https://docs.espressif.com/projects/esp-idf/en/latest/get-started/index.html) for full steps to configure and use ESP-IDF to build projects.
|
||
|
|
|
||
|
|
## Example Output
|
||
|
|
|
||
|
|
Once the upload is complete and the board is reset, the program should start running. This is reported on the monitor as below:
|
||
|
|
|
||
|
|
```
|
||
|
|
...
|
||
|
|
I (299) main_task: Calling app_main()
|
||
|
|
I (309) gpio: GPIO[0]| InputEn: 0| OutputEn: 1| OpenDrain: 0| Pullup: 1| Pulldown: 0| Intr:0
|
||
|
|
I (309) sdm_dac: Sigma-delta output is attached to GPIO 0
|
||
|
|
I (319) sdm_dac: Timer allocated with resolution 10000000 Hz
|
||
|
|
I (329) sdm_dac: Timer callback registered, interval 10 us
|
||
|
|
I (329) sdm_dac: Timer enabled
|
||
|
|
I (339) sdm_dac: Output start
|
||
|
|
```
|
||
|
|
|
||
|
|
After the output stated, you can monitor the sine wave after the filter by an oscilloscope.
|
||
|
|
|
||
|
|
|
||
|
|
|
||
|
|
## Troubleshooting
|
||
|
|
|
||
|
|
For any technical queries, please open an [issue](https://github.com/espressif/esp-idf/issues) on GitHub. We will get back to you soon.
|