The Ultra Low Power (ULP) coprocessor is a simple finite state machine (FSM) which is designed to perform measurements using the ADC, temperature sensor, and external I2C sensors, while the main processors are in Deep-sleep mode. The ULP coprocessor can access the ``RTC_SLOW_MEM`` memory region, and registers in the ``RTC_CNTL``, ``RTC_IO``, and ``SARADC`` peripherals. The ULP coprocessor uses fixed-width 32-bit instructions, 32-bit memory addressing, and has 4 general-purpose 16-bit registers. This coprocessor is referred to as ``ULP FSM`` in ESP-IDF.
{IDF_TARGET_NAME} provides a second type of ULP coprocessor which is based on a RISC-V instruction set architecture. For details regarding `ULP RISC-V` refer :doc:`ULP-RISC-V Coprocessor <../../../api-reference/system/ulp-risc-v>`.
If you have already set up ESP-IDF with CMake build system according to the :doc:`Getting Started Guide <../../../get-started/index>`, then the ULP FSM toolchain will already be installed.
The ULP FSM can be programmed using the supported instruction set. Alternatively, the ULP FSM coprocessor can also be programmed using C Macros on the main CPU. These two methods are described in the following section:
1. The ULP FSM code, written in assembly, must be added to one or more files with ``.S`` extension. These files must be placed into a separate directory inside the component directory, for instance, ``ulp/``.
When registering the component (via ``idf_component_register``), this directory should not be added to the ``SRC_DIRS`` argument. The logic behind this is that the ESP-IDF build system will compile files found in ``SRC_DIRS`` based on their extensions. For ``.S`` files, ``{IDF_TARGET_TOOLCHAIN_PREFIX}-as`` assembler is used. This is not desirable for ULP FSM assembly files, so the easiest way to achieve the distinction is by placing ULP FSM assembly files into a separate directory. The ULP FSM assembly source files should also **not** be added to ``SRCS`` for the same reason. See the steps below for how to properly add ULP FSM assembly source files.
The first argument to ``ulp_embed_binary`` specifies the ULP FSM binary name. The name specified here will also be used by other generated artifacts such as the ELF file, map file, header file and linker export file. The second argument specifies the ULP FSM assembly source files. Finally, the third argument specifies the list of component source files which include the header file to be generated. This list is needed to build the dependencies correctly and ensure that the generated header file will be created before any of these files are compiled. See the section below for the concept of generated header files for ULP applications.
1.**Run each assembly file (foo.S) through the C preprocessor.** This step generates the preprocessed assembly files (foo.ulp.S) in the component build directory. This step also generates dependency files (foo.ulp.d).
2.**Run preprocessed assembly sources through the assembler.** This produces object (foo.ulp.o) and listing (foo.ulp.lst) files. Listing files are generated for debugging purposes and are not used at later stages of the build process.
4.**Link the object files into an output ELF file** (``ulp_app_name.elf``). The Map file (``ulp_app_name.map``) generated at this stage may be useful for debugging purposes.
7.**Create an LD export script and a header file** (``ulp_app_name.ld`` and ``ulp_app_name.h``) containing the symbols from ``ulp_app_name.sym``. This is done using the ``esp32ulp_mapgen.py`` utility.
For example, the ULP FSM program may define a variable ``measurement_count`` which will define the number of ADC measurements the program needs to make before waking up the chip from Deep-sleep::
The main program needs to initialize this variable before the ULP program is started. The build system makes this possible by generating the ``${ULP_APP_NAME}.h`` and ``${ULP_APP_NAME}.ld`` files which define the global symbols present in the ULP program. Each global symbol defined in the ULP program is included in these files and are prefixed with ``ulp_``.
Note that all symbols (variables, arrays, functions) are declared as ``uint32_t``. For functions and arrays, take the address of the symbol and cast it to the appropriate type.
To access the ULP program variables from the main program, the generated header file should be included using an ``include`` statement. This will allow the ULP program variables to be accessed as regular variables::
Note that the ULP FSM program can only use the lower 16 bits of each 32-bit word in RTC memory, because the registers are 16-bit, and there is no instruction to load from the high part of the word. Likewise, the ULP store instruction writes register values into the lower 16 bits of the 32-bit word in RTC memory. The upper 16 bits are written with a value which depends on the address of the store instruction, thus when reading variables written by the ULP coprocessor, the main application needs to mask the upper 16 bits, e.g.,::
To run a ULP FSM program, the main application needs to load the ULP program into RTC memory using the :cpp:func:`ulp_load_binary` function, and then start it using the :cpp:func:`ulp_run` function.
Note that the ``Enable Ultra Low Power (ULP) Coprocessor`` option must be enabled in menuconfig to work with ULP. To select the type of ULP to be used, the ``ULP Co-processor type`` option must be set. To reserve memory for the ULP, the ``RTC slow memory reserved for coprocessor`` option must be set to a value big enough to store ULP code and data. If the application components contain multiple ULP programs, then the size of the RTC memory must be sufficient to hold the largest one.
Each ULP program is embedded into the ESP-IDF application as a binary blob. The application can reference this blob and load it in the following way (suppose ULP_APP_NAME was defined to ``ulp_app_name``)::
Declaration of the entry point symbol comes from the generated header file mentioned above, ``${ULP_APP_NAME}.h``. In the assembly source of the ULP FSM application, this symbol must be marked as ``.global``::
ESP32 ULP coprocessor is started by a timer. The timer is started once :cpp:func:`ulp_run` is called. The timer counts a number of RTC_SLOW_CLK ticks (by default, produced by an internal 150 kHz RC oscillator). The number of ticks is set using ``SENS_ULP_CP_SLEEP_CYCx_REG`` registers (x = 0..4). When starting the ULP for the first time, ``SENS_ULP_CP_SLEEP_CYC0_REG`` will be used to set the number of timer ticks. Later the ULP program can select another ``SENS_ULP_CP_SLEEP_CYCx_REG`` register using ``sleep`` instruction.
Once the timer counts the number of ticks set in the selected ``SENS_ULP_CP_SLEEP_CYCx_REG`` register, ULP coprocessor powers up and starts running the program from the entry point set in the call to :cpp:func:`ulp_run`.
The program runs until it encounters a ``halt`` instruction or an illegal instruction. Once the program halts the ULP coprocessor powers down and the timer is started again.
To disable the timer (effectively preventing the ULP program from running again), clear the ``RTC_CNTL_ULP_CP_SLP_TIMER_EN`` bit in the ``RTC_CNTL_STATE0_REG`` register. This can be done both from ULP code and from the main program.
{IDF_TARGET_NAME} ULP coprocessor is started by a timer. The timer is started once :cpp:func:`ulp_run` is called. The timer counts a number of RTC_SLOW_CLK ticks (by default, produced by an internal 90 kHz RC oscillator). The number of ticks is set using ``RTC_CNTL_ULP_CP_TIMER_1_REG`` register.
Once the timer counts the number of ticks set in the selected ``RTC_CNTL_ULP_CP_TIMER_1_REG`` register, ULP coprocessor powers up and starts running the program from the entry point set in the call to :cpp:func:`ulp_run`.
The program runs until it encounters a ``halt`` instruction or an illegal instruction. Once the program halts, ULP coprocessor powers down, and the timer is started again.
To disable the timer (effectively preventing the ULP program from running again), clear the ``RTC_CNTL_ULP_CP_SLP_TIMER_EN`` bit in the ``RTC_CNTL_ULP_CP_TIMER_REG`` register. This can be done both from ULP code and from the main program.
*:example:`system/ulp/ulp_fsm/ulp` demonstrates how to program the ULP FSM coprocessor to count pulses on an IO while the main CPUs are running other code or are in deep sleep, with the pulse count saved into NVS upon wakeup.
..only:: esp32 or esp32s3
*:example:`system/ulp/ulp_fsm/ulp_adc` demonstrates how to use the ULP FSM coprocessor to periodically measure input voltage on a specific ADC channel during deep sleep, compare it to the set threshold, and wake up the system if the voltage is outside the threshold.
