esp-idf/components/esptool_py/Kconfig.projbuild

98 lines
2.4 KiB
Plaintext
Raw Normal View History

2016-08-17 11:08:22 -04:00
menu "Serial flasher config"
config ESPTOOLPY_PORT
string "Default serial port"
default "/dev/ttyUSB0"
help
The serial port that's connected to the ESP chip. This can be overridden by setting the ESPPORT
environment variable.
choice ESPTOOLPY_BAUD
prompt "Default baud rate"
default ESPTOOLPY_BAUD_115200B
help
Default baud rate to use while communicating with the ESP chip. Can be overridden by
setting the ESPBAUD variable.
config ESPTOOLPY_BAUD_115200B
bool "115200 baud"
config ESPTOOLPY_BAUD_230400B
bool "230400 baud"
config ESPTOOLPY_BAUD_921600B
bool "921600 baud"
config ESPTOOLPY_BAUD_2MB
bool "2Mbaud"
config ESPTOOLPY_BAUD_OTHER
bool "Other baud rate"
endchoice
config ESPTOOLPY_BAUD_OTHER_VAL
int "Other baud rate value" if ESPTOOLPY_BAUD_OTHER
default 115200
config ESPTOOLPY_BAUD
int
default 115200 if ESPTOOLPY_BAUD_115200B
default 230400 if ESPTOOLPY_BAUD_230400B
default 921600 if ESPTOOLPY_BAUD_921600B
default 2000000 if ESPTOOLPY_BAUD_2MB
default ESPTOOLPY_BAUD_OTHER_VAL if ESPTOOLPY_BAUD_OTHER
config ESPTOOLPY_COMPRESSED
bool "Use compressed upload"
default "y"
help
The flasher tool can send data compressed using zlib, letting the ROM on the ESP chip
decompress it on the fly before flashing it. For most payloads, this should result in a
speed increase.
choice ESPTOOLPY_FLASHMODE
prompt "Flash SPI mode"
default ESPTOOLPY_FLASHMODE_QIO
help
Mode the flash chip is flashed in, as well as the default mode for the
binary to run in.
config ESPTOOLPY_FLASHMODE_QIO
bool "QIO"
config ESPTOOLPY_FLASHMODE_QOUT
bool "QOUT"
config ESPTOOLPY_FLASHMODE_DIO
bool "DIO"
config ESPTOOLPY_FLASHMODE_DOUT
bool "DOUT"
endchoice
config ESPTOOLPY_FLASHMODE
string
default "qio" if ESPTOOLPY_FLASHMODE_QIO
default "qout" if ESPTOOLPY_FLASHMODE_QOUT
default "dio" if ESPTOOLPY_FLASHMODE_DIO
default "dout" if ESPTOOLPY_FLASHMODE_DOUT
2016-09-02 00:29:01 -04:00
choice ESPTOOLPY_FLASHFREQ
prompt "Flash SPI speed"
default ESPTOOLPY_FLASHFREQ_40M
help
The SPI flash frequency to be used.
config ESPTOOLPY_FLASHFREQ_80M
bool "80 MHz"
config ESPTOOLPY_FLASHFREQ_40M
bool "40 MHz"
config ESPTOOLPY_FLASHFREQ_26M
bool "26 MHz"
config ESPTOOLPY_FLASHFREQ_20M
bool "20 MHz"
endchoice
config ESPTOOLPY_FLASHFREQ
string
default "80m" if ESPTOOLPY_FLASHFREQ_80M
default "40m" if ESPTOOLPY_FLASHFREQ_40M
default "26m" if ESPTOOLPY_FLASHFREQ_26M
default "20m" if ESPTOOLPY_FLASHFREQ_20M
2016-08-17 11:08:22 -04:00
endmenu