esp-idf/docs/en/api-reference/peripherals/timer.rst

109 lines
6.5 KiB
ReStructuredText
Raw Normal View History

General Purpose Timer
=====================
:link_to_translation:`zh_CN:[中文]`
{IDF_TARGET_TIMER_COUNTER_BIT_WIDTH:default="54", esp32="64", esp32s2="64"}
Introduction
------------
The {IDF_TARGET_NAME} chip contains two hardware timer groups. Each group has two general-purpose hardware timers. They are all {IDF_TARGET_TIMER_COUNTER_BIT_WIDTH}-bit generic timers based on 16-bit pre-scalers and {IDF_TARGET_TIMER_COUNTER_BIT_WIDTH}-bit up / down counters which are capable of being auto-reloaded.
Functional Overview
-------------------
The following sections of this document cover the typical steps to configure and operate a timer:
* :ref:`timer-api-timer-initialization` - covers which parameters should be set up to get the timer working, and also what specific functionality is provided depending on the timer configuration.
* :ref:`timer-api-timer-control` - describes how to read a timer's value, pause or start a timer, and change how it operates.
* :ref:`timer-api-alarms` - shows how to set and use alarms.
* :ref:`timer-api-interrupts`- explains how to use interrupt callbacks.
.. _timer-api-timer-initialization:
Timer Initialization
^^^^^^^^^^^^^^^^^^^^
The two {IDF_TARGET_NAME} timer groups, with two timers in each, provide the total of four individual timers for use. An {IDF_TARGET_NAME} timer group should be identified using :cpp:type:`timer_group_t`. An individual timer in a group should be identified with :cpp:type:`timer_idx_t`.
First of all, the timer should be initialized by calling the function :cpp:func:`timer_init` and passing a structure :cpp:type:`timer_config_t` to it to define how the timer should operate. In particular, the following timer parameters can be set:
.. list::
:not esp32: - **Clock Source**: Select the clock source, which together with the **Divider** define the resolution of the working timer. By default the clock source is APB_CLK (typically 80 MHz).
- **Divider**: Sets how quickly the timer's counter is "ticking". The setting :cpp:member:`divider` is used as a divisor of the clock source.
- **Mode**: Sets if the counter should be incrementing or decrementing. It can be defined using :cpp:member:`counter_dir` by selecting one of the values from :cpp:type:`timer_count_dir_t`.
- **Counter Enable**: If the counter is enabled, it will start incrementing / decrementing immediately after calling :cpp:func:`timer_init`. You can change the behavior with :cpp:member:`counter_en` by selecting one of the values from :cpp:type:`timer_start_t`.
- **Alarm Enable**: Can be set using :cpp:member:`alarm_en`.
- **Auto Reload**: Sets if the counter should :cpp:member:`auto_reload` the initial counter value on the timer's alarm or continue incrementing or decrementing.
To get the current values of the timer's settings, use the function :cpp:func:`timer_get_config`.
.. _timer-api-timer-control:
Timer Control
^^^^^^^^^^^^^
Once the timer is enabled, its counter starts running. To enable the timer, call the function :cpp:func:`timer_init` with :cpp:member:`counter_en` set to ``true``, or call :cpp:func:`timer_start`. You can specify the timer's initial counter value by calling :cpp:func:`timer_set_counter_value`. To check the timer's current value, call :cpp:func:`timer_get_counter_value` or :cpp:func:`timer_get_counter_time_sec`.
To pause the timer at any time, call :cpp:func:`timer_pause`. To resume it, call :cpp:func:`timer_start`.
To reconfigure the timer, you can call :cpp:func:`timer_init`. This function is described in Section :ref:`timer-api-timer-initialization`.
You can also reconfigure the timer by using dedicated functions to change individual settings:
============= =================================== ==========================================================================
Setting Dedicated Function Description
============= =================================== ==========================================================================
Divider :cpp:func:`timer_set_divider` Change the rate of ticking. To avoid unpredictable results, the timer should be paused when changing the divider. If the timer is running, :cpp:func:`timer_set_divider` pauses it, change the setting, and start the timer again.
Mode :cpp:func:`timer_set_counter_mode` Set if the counter should be incrementing or decrementing
Auto Reload :cpp:func:`timer_set_auto_reload` Set if the initial counter value should be reloaded on the timer's alarm
============= =================================== ==========================================================================
.. _timer-api-alarms:
Alarms
^^^^^^
To set an alarm, call the function :cpp:func:`timer_set_alarm_value` and then enable the alarm using :cpp:func:`timer_set_alarm`. The alarm can also be enabled during the timer initialization stage, when :cpp:func:`timer_init` is called.
After the alarm is enabled, and the timer reaches the alarm value, the following two actions can occur depending on the configuration:
* An interrupt will be triggered if previously configured. See Section :ref:`timer-api-interrupts` on how to configure interrupts.
* When :cpp:member:`auto_reload` is enabled, the timer's counter will automatically be reloaded to start counting again from a previously configured value. This value should be set in advance with :cpp:func:`timer_set_counter_value`.
.. note::
* If an alarm value is set and the timer has already reached this value, the alarm is triggered immediately.
* Once triggered, the alarm is disabled automatically and needs to be re-enabled to trigger again.
To check the specified alarm value, call :cpp:func:`timer_get_alarm_value`.
.. _timer-api-interrupts:
Interrupts
^^^^^^^^^^
Registration of an interrupt callback for a specific timer can be done by calling :cpp:func:`timer_isr_callback_add` and passing in the group ID, timer ID, callback handler and user data. The callback handler will be invoked in ISR context, so user shouldn't put any blocking API in the callback function.
The benefit of using interrupt callback instead of precessing interrupt from scratch is, you don't have to deal with interrupt status check and clean stuffs, they are all addressed before the callback got run in driver's default interrupt handler.
For more information on how to use interrupts, please see the application example below.
Application Example
-------------------
The {IDF_TARGET_TIMER_COUNTER_BIT_WIDTH}-bit hardware timer example: :example:`peripherals/timer_group`.
API Reference
-------------
.. include-build-file:: inc/timer.inc
.. include-build-file:: inc/timer_types.inc