SSD1306/SH1106 Driver for esp-idf
Go to file
2023-06-16 08:38:43 +09:00
AnimationDemo Changed log format for int32_t/uint32_t 2022-11-19 07:54:25 +09:00
components/ssd1306 Changed ic2 frequency to 400KHz. 2022-12-04 14:57:21 +09:00
CounterDemo Removed unused includes 2022-11-19 08:07:43 +09:00
ImageDemo Update README.md 2023-06-16 08:38:43 +09:00
ImageRotationDemo Added ImageRotationDemo 2023-06-16 08:36:07 +09:00
ImageScrollDemo Removed unused includes 2022-11-19 08:07:43 +09:00
MeterDemo Changed old adc driver to new driver when ESP-IDF V5 2023-01-15 10:18:39 +09:00
ScrollCounterDemo Removed unused includes 2022-11-19 08:07:43 +09:00
TextDemo Changed the operating frequency from 160MHz to 240MHz for esp32 2022-08-09 23:24:44 +09:00
WrapAroundDemo Changed the operating frequency from 160MHz to 240MHz for esp32 2022-08-09 23:24:44 +09:00
LICENSE Create LICENSE 2022-05-04 07:24:16 +09:00
README.md Update README.md 2023-01-30 12:05:45 +09:00
SSD1306_DataFormat.txt Create SSD1306_DataFormat.txt 2022-05-05 08:37:39 +09:00

esp-idf-ssd1306

SSD1306/SH1106 driver for esp-idf

I used this repository as a reference.
I used this font file.

Software requirements

esp-idf v4.4/v5.0/v5.1.

Note for ESP32C2.
ESP-IDF V5.0 ESP32C2 i2c driver has a bug.
ESP-IDF V5.1 is required when using ESP32C2.

Installation

git clone https://github.com/nopnop2002/esp-idf-ssd1306
cd esp-idf-ssd1306/TextDemo/
idf.py set-target {esp32/esp32s2/esp32s3/esp32c2/esp32c3}
idf.py menuconfig
idf.py flash

Note for ESP32C3
For some reason, there are development boards that cannot use GPIO06, GPIO08, GPIO09, GPIO19 for SPI clock pins.
According to the ESP32C3 specifications, these pins can also be used as SPI clocks.
I used a raw ESP-C3-13 to verify that these pins could be used as SPI clocks.

Configuration

You have to set this config value with menuconfig.

  • CONFIG_INTERFACE
  • CONFIG_PANEL
  • CONFIG_OFFSETX
  • CONFIG_FLIP
  • CONFIG_SDA_GPIO
  • CONFIG_SCL_GPIO
  • CONFIG_RESET_GPIO
  • CONFIG_MOSI_GPIO
  • CONFIG_SCLK_GPIO
  • CONFIG_CS_GPIO
  • CONFIG_DC_GPIO

config-main


Generic SSD1306 128x32 i2c

128x32 config-128x32_i2c

Generic SSD1306 128x64 i2c

128x64 config-128x64_i2c

Generic SH1106 128x64 i2c

Hardware scroll Not support
Left:1.3 inch SH1106
Right:0.96 inch SSD1306

SH1106_i2c config-sh1106_i2c

128x64 TTGO

Unlike other ESP32 development boards, the RTC_CLOCK crystal on this board uses a 26MHz one.
You need to change the RTC CLOCK frequency to 26MHz using menuconfig.

ESP32-TTGO-1 ESP32-TTGO-2 128x64_Reset config-128x64_TTGO

128x64 ESP-WROOM-32

ESP32-OLED-2 config-ESP-WROOM-32


Generic SSD1306 128x32 SPI

128x32_spi config-128x32_spi

Generic SSD1306 128x64 SPI

D0 is SCLK.
D1 is MOSI.

128x64_spi config-128x64_spi

Generic SH1106 128x64 SPI

Hardware scroll Not support
Left:1.3 inch SH1106
Right:0.96 inch SSD1306

SH1106_spi config-sh1106_spi


SPI BUS selection

config-spi-bus

The ESP32 series has three SPI BUSs.
SPI1_HOST is used for communication with Flash memory.
You can use SPI2_HOST and SPI3_HOST freely.
When you use SDSPI(SD Card via SPI), SDSPI uses SPI2_HOST BUS.
When using this module at the same time as SDSPI or other SPI device using SPI2_HOST, it needs to be changed to SPI3_HOST.
When you don't use SDSPI, both SPI2_HOST and SPI3_HOST will work.
Previously it was called HSPI_HOST / VSPI_HOST, but now it is called SPI2_HOST / SPI3_HOST.


Flip upside down

config_flip

ssd1306_flip