2024-04-12 21:43:37 -04:00
|
|
|
# ESP32S2 Mini Multi PCB
|
|
|
|
|
Several products of ESP32 equipped with SSD1306 are available.
|
|
|
|
|
However, I have never seen a product equipped with an SSD1306 with an SPI interface.
|
|
|
|
|
Also, I have never seen a product equipped with a 1.3 inch SSD1306 product.
|
|
|
|
|
Therefore, I designed a PCB that can be equipped with an SPI interface and 1.3 inch products.
|
2024-04-12 21:47:09 -04:00
|
|
|
I use ESP32S2-Mini Development board.
|
2024-04-12 21:43:37 -04:00
|
|
|
Although this product is very small, it is equipped with 2MB of PSRAM.
|
|
|
|
|
|
2024-04-12 21:44:46 -04:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2024-04-12 21:43:37 -04:00
|
|
|
|
2024-04-12 22:22:50 -04:00
|
|
|
You can download the Garbers file from [here](https://www.pcbway.com/project/shareproject/esp32s2_ssd1306_multi_pcb_2d6e5b26.html).
|
2024-04-12 22:01:52 -04:00
|
|
|
You can use the zip file to order it yourself from PCB manufacturing vendors such as Elecrow/FusionPCB/PCBWay.
|
2024-04-12 21:47:09 -04:00
|
|
|
I ordered it on 3/31 and it arrived on 4/9.
|
2024-04-12 21:43:37 -04:00
|
|
|
You can repeat my order from [here](https://www.pcbway.com/project/shareproject/esp32s2_ssd1306_multi_pcb_2d6e5b26.html).
|
|
|
|
|
|
2024-04-12 23:08:20 -04:00
|
|
|
# Configuration
|
2024-04-12 23:09:22 -04:00
|
|
|
for SPI interface
|
2024-04-12 23:08:20 -04:00
|
|
|
|
|
|
|
|
|
2024-04-12 23:09:22 -04:00
|
|
|
for I2C interface
|
2024-04-12 23:08:20 -04:00
|
|
|
|
2024-04-12 21:43:37 -04:00
|
|
|
|
2024-04-23 07:34:25 -04:00
|
|
|
# Why ESP32S2 Mini?
|
2024-04-23 07:33:58 -04:00
|
|
|
cheap!!
|
|
|
|
|
Only $1.49.
|
|
|
|
|
|
2024-04-12 21:43:37 -04:00
|
|
|
# About ESP32S2 Mini
|
|
|
|
|
A Type-C USB connector is mounted on the board, but a USB-TTL conversion chip is not mounted.
|
|
|
|
|
The circuit diagram is available [here](https://www.wemos.cc/en/latest/_static/files/sch_s2_mini_v1.0.0.pdf).
|
|
|
|
|
USB ports D- and D+ are connected to GPIO19/20.
|
|
|
|
|
Since it uses the chip's USB-OTG function, it will not be recognized as a USB device even if you simply connect it to the host with a USB cable.
|
|
|
|
|
To write firmware, press ButtonRST while pressing Button0, then release ButtonRST and then Button0.
|
|
|
|
|
Now the device will enter DFU mode, the USB device (/dev/ttyACM0) will appear, and you can upload the firmware.
|
2024-04-12 23:12:53 -04:00
|
|
|
Once the firmware upload is complete, press ButtonRST again.
|
|
|
|
|
The firmware will now start.
|
2024-04-12 21:43:37 -04:00
|
|
|
If you press ButtonRST without pressing Button0, the USB device will disappear.
|
|
|
|
|
In other words, USB can be used for writing, but not for STDOUT.
|
2024-04-12 22:05:26 -04:00
|
|
|
On ESP32-S2, GPIO43/44 are U0TXD/U0RXD, but this GPIO is not present on the pin header.
|
2024-04-12 21:43:37 -04:00
|
|
|
|
2024-04-12 22:17:32 -04:00
|
|
|
My board has 4MB of FLASH and ___2MB of PSRAM___.
|
2024-04-12 21:43:37 -04:00
|
|
|
It's strange that it is recognized as having an external flash.
|
|
|
|
|
There is no external flash anywhere on the board.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
# Enable PSRAM
|
|
|
|
|
In order to use PSRAM, you need to enable PSRAM by following the steps below.
|
2024-04-12 22:08:42 -04:00
|
|
|
Please note that this procedure is for ESP-IDF V5.2 and may change in the future.
|
2024-04-12 21:43:37 -04:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
