/** * --------------------------------------------------------------------------------------+ * @desc SSD1306 OLED Driver * --------------------------------------------------------------------------------------+ * Copyright (C) 2020 Marian Hrinko. * Written by Marian Hrinko (mato.hrinko@gmail.com) * * @author Marian Hrinko * @datum 06.10.2020 * @update 24.11.2022 * @file ssd1306.c * @version 3.0 * @tested AVR Atmega328p * * @depend font.h, twi.h * --------------------------------------------------------------------------------------+ * @descr Version 1.0 -> applicable for 1 display * Version 2.0 -> rebuild to 'cacheMemLcd' array * Version 3.0 -> remove 'cacheMemLcd' approach * --------------------------------------------------------------------------------------+ * @usage Basic Setup for OLED Display */ #include "ssd1306.h" // +---------------------------+ // | Set MUX Ratio | // +---------------------------+ // | 0xA8, 0x3F | // +---------------------------+ // | // +---------------------------+ // | Set Display Offset | // +---------------------------+ // | 0xD3, 0x00 | // +---------------------------+ // | // +---------------------------+ // | Set Display Start Line | // +---------------------------+ // | 0x40 | // +---------------------------+ // | // +---------------------------+ // | Set Segment Remap | // +---------------------------+ // | 0xA0 / 0xA1 | // +---------------------------+ // | // +---------------------------+ // | Set COM Output Scan | // | Direction | // +---------------------------+ // | 0xC0 / 0xC8 | // +---------------------------+ // | // +---------------------------+ // | Set COM Pins hardware | // | configuration | // +---------------------------+ // | 0xDA, 0x02 | // +---------------------------+ // | // +---------------------------+ // | Set Contrast Control | // +---------------------------+ // | 0x81, 0x7F | // +---------------------------+ // | // +---------------------------+ // | Disable Entire Display On | // +---------------------------+ // | 0xA4 | // +---------------------------+ // | // +---------------------------+ // | Set Normal Display | // +---------------------------+ // | 0xA6 | // +---------------------------+ // | // +---------------------------+ // | Set Osc Frequency | // +---------------------------+ // | 0xD5, 0x80 | // +---------------------------+ // | // +---------------------------+ // | Enable charge pump | // | regulator | // +---------------------------+ // | 0x8D, 0x14 | // +---------------------------+ // | // +---------------------------+ // | Display On | // +---------------------------+ // | 0xAF | // +---------------------------+ // @array Init command const uint8_t INIT_SSD1306[] PROGMEM = { 18, // number of initializers 0, SSD1306_DISPLAY_OFF, // 0xAE = Set Display OFF 1, SSD1306_SET_MUX_RATIO, 0x3F, // 0xA8 - 64MUX 1, SSD1306_MEMORY_ADDR_MODE, 0x00, // 0x20 = Set Memory Addressing Mode // 0x00 - Horizontal Addressing Mode // 0x01 - Vertical Addressing Mode // 0x02 - Page Addressing Mode (RESET) 2, SSD1306_SET_COLUMN_ADDR, START_COLUMN_ADDR, END_COLUMN_ADDR, // 0x21 = Set Column Address, 0 - 127 2, SSD1306_SET_PAGE_ADDR, START_PAGE_ADDR, END_PAGE_ADDR, // 0x22 = Set Page Address, 0 - 7 0, SSD1306_SET_START_LINE, // 0x40 1, SSD1306_DISPLAY_OFFSET, 0x00, // 0xD3 0, SSD1306_SEG_REMAP_OP, // 0xA0 / remap 0xA1 0, SSD1306_COM_SCAN_DIR_OP, // 0xC0 / remap 0xC8 1, SSD1306_COM_PIN_CONF, 0x12, // 0xDA, 0x12 - Disable COM Left/Right remap, Alternative COM pin configuration 1, SSD1306_SET_CONTRAST, 0x7F, // 0x81, 0x7F - reset value (max 0xFF) 0, SSD1306_DIS_ENT_DISP_ON, // 0xA4 0, SSD1306_DIS_NORMAL, // 0xA6 1, SSD1306_SET_OSC_FREQ, 0x80, // 0xD5, 0x80 => D=1; DCLK = Fosc / D <=> DCLK = Fosc 1, SSD1306_SET_PRECHARGE, 0xc2, // 0xD9, higher value less blinking // 0xC2, 1st phase = 2 DCLK, 2nd phase = 13 DCLK 1, SSD1306_VCOM_DESELECT, 0x20, // Set V COMH Deselect, reset value 0x22 = 0,77xUcc 1, SSD1306_SET_CHAR_REG, 0x14, // 0x8D, Enable charge pump during display on 0, SSD1306_DISPLAY_ON // 0xAF = Set Display ON }; unsigned short int _indexCol = START_COLUMN_ADDR; // @var global - cache index column unsigned short int _indexPage = START_PAGE_ADDR; // @var global - cache index page /** * @desc SSD1306 Init * * @param void * * @return uint8_t */ uint8_t SSD1306_Init (void) { const uint8_t *commands = INIT_SSD1306; // variables unsigned short int no_of_commands = pgm_read_byte(commands++); // number of commands uint8_t no_of_arguments; // number od arguments uint8_t command; // command uint8_t status = INIT_STATUS; // TWI init status 0xFF // TWI INIT // ------------------------------------------------------------------------------------- TWI_Init (); // TWI Start & SLAW // ------------------------------------------------------------------------------------- status = SSD1306_Send_StartAndSLAW (SSD1306_ADDR); // start & SLAW if (SSD1306_SUCCESS != status) { // check status return status; // error } // MAIN LOOP // ------------------------------------------------------------------------------------- while (no_of_commands) { // commands loop no_of_arguments = pgm_read_byte (commands++); // number of arguments command = pgm_read_byte (commands++); // command // SEND COMMAND // ----------------------------------------------------------------------------------- status = SSD1306_Send_Command (command); // send command if (SSD1306_SUCCESS != status) { // check status return status; // error } // SEND ARGUMENTS // ----------------------------------------------------------------------------------- while (no_of_arguments--) { status = SSD1306_Send_Command (pgm_read_byte(commands++)); // send argument if (SSD1306_SUCCESS != status) { // check status return status; // error } } no_of_commands--; // next command } // TWI STOP // ------------------------------------------------------------------------------------- TWI_Stop (); return SSD1306_SUCCESS; // success } /** * @desc SSD1306 Send Start and SLAW request * * @param uint8_t * * @return uint8_t */ uint8_t SSD1306_Send_StartAndSLAW (uint8_t address) { uint8_t status = INIT_STATUS; // TWI init status 0xFF // TWI START // ------------------------------------------------------------------------------------- status = TWI_MT_Start (); // start if (SSD1306_SUCCESS != status) { // check status return status; // error } // TWI start & SLAW // ------------------------------------------------------------------------------------- status = TWI_MT_Send_SLAW (address); // start & SLAW if (SSD1306_SUCCESS != status) { // check status return status; // error } return SSD1306_SUCCESS; // success } /** * @desc SSD1306 Send command * * @param uint8_t command * * @return uint8_t */ uint8_t SSD1306_Send_Command (uint8_t command) { uint8_t status = INIT_STATUS; // TWI init status 0xFF // TWI send control byte // ------------------------------------------------------------------------------------- status = TWI_MT_Send_Data (SSD1306_COMMAND); // send control byte if (SSD1306_SUCCESS != status) { // check status return status; // error } // TWI send command // ------------------------------------------------------------------------------------- status = TWI_MT_Send_Data (command); // send command if (SSD1306_SUCCESS != status) { // check status return status; // error } return SSD1306_SUCCESS; // success } /** * @desc SSD1306 Normal colors * * @param void * * @return uint8_t */ uint8_t SSD1306_NormalScreen (void) { uint8_t status = INIT_STATUS; // TWI init status 0xFF // TWI start & SLAW // ------------------------------------------------------------------------------------- status = SSD1306_Send_StartAndSLAW (SSD1306_ADDR); // start & SLAW if (SSD1306_SUCCESS != status) { // check status return status; // error } // TWI send command // ------------------------------------------------------------------------------------- status = SSD1306_Send_Command (SSD1306_DIS_NORMAL); // command 0xA6 if (SSD1306_SUCCESS != status) { // check status return status; // error } return SSD1306_SUCCESS; // success } /** * @desc SSD1306 Inverse colors * * @param void * * @return uint8_t */ uint8_t SSD1306_InverseScreen (void) { uint8_t status = INIT_STATUS; // TWI init status 0xFF // TWI start & SLAW // ------------------------------------------------------------------------------------- status = SSD1306_Send_StartAndSLAW (SSD1306_ADDR); // start & SLAW if (SSD1306_SUCCESS != status) { // check status return status; // error } // TWI send command // ------------------------------------------------------------------------------------- status = SSD1306_Send_Command (SSD1306_DIS_INVERSE); // command 0xA7 if (SSD1306_SUCCESS != status) { // check status return status; // error } return SSD1306_SUCCESS; // success } /** * @desc SSD1306 Clear screen * * @param void * * @return uint8_t */ uint8_t SSD1306_ClearScreen (void) { uint8_t status = INIT_STATUS; // TWI init status 0xFF uint16_t i = 0; // counter // TWI start & SLAW // ------------------------------------------------------------------------------------- status = SSD1306_Send_StartAndSLAW (SSD1306_ADDR); // start & SLAW if (SSD1306_SUCCESS != status) { // check status return status; // error } // TWI control byte data stream // ------------------------------------------------------------------------------------- status = TWI_MT_Send_Data (SSD1306_DATA_STREAM); // send data 0x40 if (SSD1306_SUCCESS != status) { // check status return status; // error } // send clear byte to memory lcd // ------------------------------------------------------------------------------------- while (i < CACHE_SIZE_MEM) { status = TWI_MT_Send_Data (CLEAR_COLOR); // send data 0x00 if (SSD1306_SUCCESS != status) { // check status return status; // error } i++; // update counter } // TWI stop // ------------------------------------------------------------------------------------- TWI_Stop (); return SSD1306_SUCCESS; // success } /** * @desc SSD1306 Set position * * @param uint8_t column -> 0 ... 127 * @param uint8_t page -> 0 ... 7 * * @return void */ uint8_t SSD1306_SetPosition (uint8_t x, uint8_t y) { uint8_t status = INIT_STATUS; // TWI init status 0xFF // TWI start & SLAW // ------------------------------------------------------------------------------------- status = SSD1306_Send_StartAndSLAW (SSD1306_ADDR); // start & SLAW if (SSD1306_SUCCESS != status) { // check status return status; // error } // COLUMN // ------------------------------------------------------------------------------------- status = SSD1306_Send_Command (SSD1306_SET_COLUMN_ADDR); // 0x21 if (SSD1306_SUCCESS != status) { // check status return status; // error } // start COLUMN status = SSD1306_Send_Command (x); if (SSD1306_SUCCESS != status) { // check status return status; // error } // end COLUMN status = SSD1306_Send_Command (END_COLUMN_ADDR); // 127 if (SSD1306_SUCCESS != status) { // check status return status; // error } // update column index _indexCol = x; // PAGE // ------------------------------------------------------------------------------------- status = SSD1306_Send_Command (SSD1306_SET_PAGE_ADDR); // 0x22 if (SSD1306_SUCCESS != status) { // check status return status; // error } // start PAGE status = SSD1306_Send_Command (y); if (SSD1306_SUCCESS != status) { // check status return status; // error } // end PAGE status = SSD1306_Send_Command (END_PAGE_ADDR); // 7 for 128x64 if (SSD1306_SUCCESS != status) { // check status return status; // error } // update column index _indexPage = y; // TWI stop // ------------------------------------------------------------------------------------- TWI_Stop (); return SSD1306_SUCCESS; // success } /** * @desc SSD1306 Update text poisition - this ensure that character will not be divided * at the end of row, the whole character will be depicted on the new row * * @param void * * @return uint8_t */ uint8_t SSD1306_UpdatePosition (void) { uint8_t status = INIT_STATUS; // TWI init status 0xFF uint8_t x = _indexCol + CHARS_COLS_LENGTH + 1; // check end col position // check position // ------------------------------------------------------------------------------------- if (x > END_COLUMN_ADDR) { // last page not reached // ----------------------------------------------------------------------------------- if (_indexPage < END_PAGE_ADDR) { _indexCol = 0; // update column _indexPage = _indexPage + 1; // update page status = SSD1306_SetPosition (_indexCol, _indexPage); // update position if (SSD1306_SUCCESS != status) { // check status return status; // error } } // last page reached // ----------------------------------------------------------------------------------- if (_indexPage >= END_PAGE_ADDR) { return SSD1306_ERROR; // return out of range } } return SSD1306_SUCCESS; // success } /** * @desc SSD1306 Draw character * * @param char character * * @return uint8_t */ uint8_t SSD1306_DrawChar (char ch) { uint8_t status = INIT_STATUS; // TWI init status 0xFF uint16_t i = 0; // counter // update text position // ------------------------------------------------------------------------------------- status = SSD1306_UpdatePosition(); if (SSD1306_SUCCESS != status) { // check status return status; // error } // TWI start & SLAW // ------------------------------------------------------------------------------------- status = SSD1306_Send_StartAndSLAW (SSD1306_ADDR); // start & SLAW if (SSD1306_SUCCESS != status) { // check status return status; // error } // TWI control byte data stream // ------------------------------------------------------------------------------------- status = TWI_MT_Send_Data (SSD1306_DATA_STREAM); // send data 0x40 if (SSD1306_SUCCESS != status) { // check status return status; // error } // send character byte to memory lcd // ------------------------------------------------------------------------------------- while (i < CHARS_COLS_LENGTH) { status = TWI_MT_Send_Data (pgm_read_byte (&FONTS[ch-32][i])); // send data col if (SSD1306_SUCCESS != status) { // check status return status; // error } i++; // update counter } // send empty column to memory lcd // ------------------------------------------------------------------------------------- status = TWI_MT_Send_Data (CLEAR_COLOR); // ONE empty column if (SSD1306_SUCCESS != status) { // check status return status; // error } _indexCol = _indexCol + CHARS_COLS_LENGTH + 1; // update global col // TWI stop // ------------------------------------------------------------------------------------- TWI_Stop (); return SSD1306_SUCCESS; // success } /** * @desc SSD1306 Draw String * * @param char * string * * @return uint8_t */ uint8_t SSD1306_DrawString (char *str) { uint8_t i = 0; // char counter // send characters of string // ------------------------------------------------------------------------------------- while (str[i] != '\0') { SSD1306_DrawChar (str[i++]); // send char } return SSD1306_SUCCESS; // success } /** * @desc Draw pixel * * @param uint8_t x -> 0 ... MAX_X * @param uint8_t y -> 0 ... MAX_Y * * @return uint8_t */ uint8_t SSD1306_DrawPixel (uint8_t x, uint8_t y) { uint8_t page = 0; // page uint8_t pixel = 0; // pixel uint8_t status = INIT_STATUS; // TWI init status 0xFF if ((x > MAX_X) && (y > MAX_Y)) { // if out of range return SSD1306_ERROR; // error } page = y >> 3; // find page (y / 8) pixel = 1 << (y - (page << 3)); // which pixel (y % 8) <<<<<<< HEAD // set position // ------------------------------------------------------------------------------------- status = SSD1306_SetPosition (x, page); // update position if (SSD1306_SUCCESS != status) { // check status return status; // error ======= // set position // ------------------------------------------------------------------------------------- status = SSD1306_SetPosition (x, page); // update position if (SSD1306_SUCCESS != status) { // check status return status; // error } // TWI start & SLAW // ------------------------------------------------------------------------------------- status = SSD1306_Send_StartAndSLAW (SSD1306_ADDR); // start & SLAW if (SSD1306_SUCCESS != status) { // check status return status; // error } // TWI control byte data stream // ------------------------------------------------------------------------------------- status = TWI_MT_Send_Data (SSD1306_DATA_STREAM); // send data 0x40 if (SSD1306_SUCCESS != status) { // check status return status; // error } // send clear byte to memory lcd // ------------------------------------------------------------------------------------- status = TWI_MT_Send_Data (pixel); // send pixel if (SSD1306_SUCCESS != status) { // check status return status; // error } // TWI stop // ------------------------------------------------------------------------------------- TWI_Stop (); return SSD1306_SUCCESS; // success } /** * @desc Draw line by Bresenham algoritm * * @param uint8_t x start position / 0 <= cols <= MAX_X-1 * @param uint8_t x end position / 0 <= cols <= MAX_X-1 * @param uint8_t y start position / 0 <= rows <= MAX_Y-1 * @param uint8_t y end position / 0 <= rows <= MAX_Y-1 * * @return uint8_t */ uint8_t SSD1306_DrawLine (uint8_t x1, uint8_t x2, uint8_t y1, uint8_t y2) { int16_t D; // determinant int16_t delta_x, delta_y; // deltas int16_t trace_x = 1, trace_y = 1; // steps delta_x = x2 - x1; // delta x delta_y = y2 - y1; // delta y // Vertical line // ------------------------------------------------------------------------------------- if (delta_x == 0) { status = SSD1306_DrawLineVert (x1, y1, y2); // draw vertical line if (SSD1306_SUCCESS != status) { // check status return status; // error } return SSD1306_SUCCESS; // success return } // Horizontal line // ------------------------------------------------------------------------------------- if (delta_y == 0) { status = SSD1306_DrawLineHorz (y1, x1, x2); // draw horizontal line if (SSD1306_SUCCESS != status) { // check status return status; // error } return SSD1306_SUCCESS; // success return } if (delta_x < 0) { // check if x2 > x1 delta_x = -delta_x; // negate delta x trace_x = -trace_x; // negate step x >>>>>>> origin/develop } // TWI start & SLAW // ------------------------------------------------------------------------------------- status = SSD1306_Send_StartAndSLAW (SSD1306_ADDR); // start & SLAW if (SSD1306_SUCCESS != status) { // check status return status; // error } <<<<<<< HEAD // TWI control byte data stream // ------------------------------------------------------------------------------------- status = TWI_MT_Send_Data (SSD1306_DATA_STREAM); // send data 0x40 if (SSD1306_SUCCESS != status) { // check status return status; // error } // send clear byte to memory lcd // ------------------------------------------------------------------------------------- status = TWI_MT_Send_Data (pixel); // send pixel if (SSD1306_SUCCESS != status) { // check status return status; // error } // TWI stop // ------------------------------------------------------------------------------------- TWI_Stop (); return SSD1306_SUCCESS; // success ======= // condition for m < 1 (dy < dx) // ------------------------------------------------------------------------------------- if (delta_y < delta_x) { // D = (delta_y << 1) - delta_x; // calculate determinant SSD1306_DrawPixel (x1, y1); // draw first pixel while (x1 != x2) { // check if x1 equal x2 x1 += trace_x; // update x1 if (D >= 0) { // positive? y1 += trace_y; // update y1 D -= 2*delta_x; // update determinant } D += 2*delta_y; // update deteminant SSD1306_DrawPixel (x1, y1); // draw next pixel } // condition for m >= 1 (dy >= dx) // ------------------------------------------------------------------------------------- } else { D = delta_y - (delta_x << 1); // calculate determinant SSD1306_DrawPixel (x1, y1); // draw first pixel while (y1 != y2) { // check if y2 equal y1 y1 += trace_y; // update y1 if (D <= 0) { // positive? x1 += trace_x; // update y1 D += 2*delta_y; // update determinant } D -= 2*delta_x; // update deteminant SSD1306_DrawPixel (x1, y1); // draw next pixel } } return SSD1306_SUCCESS; // success return >>>>>>> origin/develop }