GY-63_MS5611/libraries/AD5263
2024-03-17 16:42:35 +01:00
..
.github 0.1.3 AD5263 2024-03-17 16:42:35 +01:00
examples 0.1.3 AD5263 2024-03-17 16:42:35 +01:00
test 0.1.3 AD5263 2024-03-17 16:42:35 +01:00
.arduino-ci.yml 0.1.3 AD5263 2024-03-17 16:42:35 +01:00
AD5263.cpp 0.1.3 AD5263 2024-03-17 16:42:35 +01:00
AD5263.h 0.1.3 AD5263 2024-03-17 16:42:35 +01:00
CHANGELOG.md 0.1.3 AD5263 2024-03-17 16:42:35 +01:00
keywords.txt 0.1.3 AD5263 2024-03-17 16:42:35 +01:00
library.json 0.1.3 AD5263 2024-03-17 16:42:35 +01:00
library.properties 0.1.3 AD5263 2024-03-17 16:42:35 +01:00
LICENSE 0.1.3 AD5263 2024-03-17 16:42:35 +01:00
README.md 0.1.3 AD5263 2024-03-17 16:42:35 +01:00

Arduino CI Arduino-lint JSON check GitHub issues

License: MIT GitHub release PlatformIO Registry

AD5263

Arduino library for I2C digital potentiometer AD5263 and compatibles.

Description

The AD5263 is a digital potentiometer with 4 channels and very much alike the AD524X (single / dual channels). This digital potentiometers come in 20, 50 and 200 kΩ and can be set in 256 steps. This library only implements the I2C interface (See future for SPI).

An important property of the AD5263 device is that it defaults to their mid position at startup. The library defines AD5263_MIDPOINT == 128 (as per datasheet). To be used to set to defined mid-point.

(Library is based on datasheet Rev.F )

This library is related to

Compatibles

None known so far.

Hardware connection AD5263

Please read datasheet for all details!

Pin Name Description (short) Notes
1 B1 Resistor Terminal B1.
2 A1 Resistor Terminal A1 (ADDR = 00)
3 W1 Wiper Terminal W1.
4 B3 Resistor Terminal B3.
5 A3 Resistor Terminal A3.
6 W3 Wiper Terminal W3 (ADDR = 10)
7 VDD Positive Power Supply
8 GND Ground.
9 DIS SPI/I2C Select. SPI = 0, I2C = 1 connect to VDD
10 VLOGIC 2.7 - 5.5V Logic Supply Voltage. connect to VDD
11 SDI/SDA (SPI data in) I2C SDA
12 CLK/SCL Serial Clock I2C SCL
13 CS/AD0 (SPI Chip Select). I2C address bit 0 see Address below
14 RES/AD1 (SPI RESET) I2C Address bit 1 see Address below
15 SHDN Shutdown. Tie to +5 V if not used.
16 SDO/O1 (SPI data out) I2C Output O1
17 NC/O2 (SPI No Connect) I2C Output O2
18 VSS Negative Power Supply.
19 W4 Wiper Terminal W4 (ADDR = 11)
20 A4 Resistor Terminal A4.
21 B4 Resistor Terminal B4.
22 W2 Wiper Terminal W2 (ADDR = 01)
23 A2 Resistor Terminal A2.
24 B2 Resistor Terminal B2.

VLOGIC

The logic supply voltage should always be less than or equal to VDD. In addition, logic levels must be limited to the logic supply voltage regardless of VDD.

I2C

Address

The AD5263 has two address lines to configure the I2C address. 0x2C - 0x2F

Addr(dec) Addr(Hex) AD0 AD1 Notes
44 0x2C GND GND
45 0x2D GND +5V
46 0x2E +5V GND
47 0x2F +5V +5V

Note the AD5263 uses the same range as the AD524X devices.

Performance

Timing in microseconds, writing a new value to device.

Speed UNO ESP32 RP2040 notes
100000 340
150000 240
200000 196
250000 168
300000 148
350000 140
400000 136 max advised speed
450000 128
500000 124 max working speed

The Arduino UNO failed to communicate above 500K, therefore the maximum speed advised is 400000 bits/sec.

TODO Test with ESP32 / RP2040 / ... to fill the table

Interface

#include "AD5263.h"

The library has a number of functions which are all quite straightforward. One can get / set the value of (both) the potentiometer(s), and the O1 and O2 output lines.

Constructors

  • AD5263(uint8_t address, TwoWire *wire = &Wire) constructor, creates an instance with 4 potentiometer.
  • bool begin() if connected begin() resets the device, otherwise returns false.
  • bool isConnected() See if address set in constructor is on the bus.
  • uint8_t getAddress() Returns address set in the constructor.

Basic IO

  • uint8_t write(uint8_t rdac, uint8_t value) set channel rdac 0..3 to value 0..255.
  • uint8_t write(uint8_t rdac, uint8_t value, uint8_t O1, uint8_t O2) idem + set output lines O1 and O2 too.
  • uint8_t read(uint8_t rdac) read back set value. rdac should be 0..3.
  • uint8_t setO1(uint8_t value = HIGH) value = HIGH (default) or LOW.
  • uint8_t setO2(uint8_t value = HIGH) value = HIGH (default) or LOW.
  • uint8_t getO1() read back O1 line.
  • uint8_t getO2() read back O2 line.

Misc

  • uint8_t zeroAll() sets potentiometer's to 0 and I/O to LOW.
  • uint8_t reset() sets potentiometer's to midpoint == 128 and O1 and O2 to LOW. (startup default)
  • uint8_t setAll(uint8_t value) sets potentiometer's to value and O1 and O2 to LOW.
  • uint8_t midScaleReset(uint8_t rdac) resets one potentiometer to midpoint == 128.
  • uint8_t readBackRegister() read register back, for debugging.

Experimental

  • uint8_t shutDown() check datasheet, not tested, use at own risk.

Error codes

define value
AD5263_OK 0
AD5263_ERROR 100

Future

Must

  • update documentation.

Should

Could

  • improve error handling.
  • sync with AD520X / AD524X library
  • optimize footprint write() versions.
  • optimize midScaleReset() = return write(rdac, AD5263_MIDPOINT);
    • is this the same?
  • investigate SPI interface (performance better)

Wont

Support

If you appreciate my libraries, you can support the development and maintenance. Improve the quality of the libraries by providing issues and Pull Requests, or donate through PayPal or GitHub sponsors.

Thank you,